<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<!-- this stylesheet will later on be added by lfparser automatically: -->
<style type="text/css">
<!--
pre { font-family:monospace,Courier }
p.code { width:80%; alignment:center; background-color:#aedbe8; border-style:no ne; border-width:medium; border-color:#aedbe8; padding:0.1cm ; text-align:left }
-->
</style>
<title>A Microcontroller based DC power supply</title>
</head>
<body>
<h1>A Microcontroller based DC power supply</h1>
<h4>ArticleCategory: [Choose a category, do not translate
this]</h4>
Hardware
<h4>AuthorImage:[Here we need a little image from you]</h4>
<img src="../../common/images/Guido-S.gif" alt=
"[Photo of the Author]" height="164" width="173">
<h4>TranslationInfo:[Author + translation history. mailto: or
http://homepage]</h4>
<p>original in en <a href="http://linuxfocus.org/~guido/">Guido
Socher</a></p>
<h4>AboutTheAuthor:[A small biography about the author]</h4>
<p>Guido loves Linux not only because it is fun to discover the
great possibilities of this systems but also because of the
people involved in its design.</p>
<h4>Abstract:[Here you write a little summary]</h4>
This article is the 4th article in the Linux<font color=
"#FF0000">Focus</font> AT90S4433 Microcontroller series. I
suggest you to read the previous articles on Atmel
Microcontrollers programming with regards to:
<ol>
<li>How to install and use the Linux AVR development
environment and how to build the programmer hardware:<br>
<a href="../March2002/article231.shtml">March 2002,
Programming the AVR Microcontroller with GCC</a></li>
<li>How to make your own printed circuit board:<br>
<a href="../May2002/article236.shtml">May 2002, A LCD control
panel for your Linux server</a></li>
<li>How to build the case/box for your power supply:<br>
<a href="../September2002/article253.shtml">September 2002,
Frequency counter 1Hz-100Mhz with LCD display and RS232
interface</a></li>
</ol>
One of the most important devices for your workshop at home is
a good, and reliable DC power supply. In this article we will
build such a power supply. It will be Microcontroller
controlled. It has a LCD display, and you can send it commands
from your Linux computer via RS232 interface. It has a very
robust design. <br>
<br>
This article shows also how versatile Microcontrollers are. It
is however not the simplest circuit. <br>
If you are just looking a simple DC power supply then take a
look at the <a href=
"../../common/src/article251/simpleDCpower/">"simple DC
power"</a>. The simple DC is good if you just need a small
power supply unit for the other electronic experiments in
Linux<font color="#FF0000">Focus</font>. It has however nothing
to do with Linux and software in general. <br>
Even if you finally only build the "simple DC power" unit you
can read on and learn many interessting aspects about
Microcontrollers.
<h4>ArticleIllustration:[This is the title picture for your
article]</h4>
<img src="../../common/images/article251/dcpower-logo.gif"
width="202" height="160" alt="[Illustration]" hspace="10">
<h4>ArticleBody:[The article body]</h4>
<h2>Introduction</h2>
This Microcontroller bases DC power supply is not the simplest
circuit but I can assure you that you will not regret the time
needed to build it. It is very robust and reliable. It is also
technically very interesting, because you will learn how to
generate a analog DC voltage with a Microcontroller without
using a DA-converter chip. <br>
<br>
You need a lot of parts for this article but those are only
cheap standard parts. This power supply is not expensive. <br>
<h2>What you need</h2>
See this <a href=
"../../common/src/article251/partlist.html">part list</a> for a
listing of all the parts that you need. You can also see the
needed parts with their values in the schematic below. <br>
Our power supply comes in 3 variants. Except for the
transformer and one resistor there is only a modification in
the software required. All other parts are identical for all 3
options:
<ol>
<li>0-16V Imax=2.2A<br>
buy a transformer with 15V 2.5A</li>
<li>0-24V Imax=2.2A<br>
buy a transformer with 24V 2.5A</li>
<li>0-30V Imax=3A<br>
buy a transformer with 30V 3A</li>
</ol>
Note: In all three cases you need of course the additional 9V, 100mA transformer
for the power to the main board.
<h2>Schematic and board</h2>
I used <a href="http://www.cadsoftusa.com/">eagle</a> for Linux
to design the schematic and board. The eagle files are also
included in the tar.gz package together with the software. You
can download it at the end of the article. <br>
<br>
The circuit is divided into 2 parts. One main part and one part
that should be close to the power transistors. Below you see 2
independent schematic diagramms for the two parts but they are
finally to be connected via wires. <br>
<br>
The main schematic (click on it for a bigger picture):<br>
<a href="../../common/images/article251/schematic.gif"><img
src="../../common/images/article251/schematic_th.gif" width=
"576" height="346" alt="[main schematic]"></a> <br>
<br>
The schematic for the high power part (click on it for a
bigger picture):<br>
<a href=
"../../common/images/article251/schematic_powerpart.gif"><img
src="../../common/images/article251/schematic_powerpart_th.gif"
width="577" height="325" alt="[power part schematic]"></a> <br>
How to connect the push buttons in a matrix (click on it for a
bigger picture):<br>
<a href=
"../../common/images/article251/push_buttons_schematic.gif"><img
src=
"../../common/images/article251/push_buttons_schematic_th.gif"
width="277" height="103" alt="[push buttons schematic]"></a>
<br>
<br>
The main board, top view (click on it for a bigger
picture):<br>
<a href=
"../../common/images/article251/linuxDCpower_board_white.gif"><img
src=
"../../common/images/article251/linuxDCpower_board_white_th.jpg"
width="363" height="284" alt="[board]"></a> <br>
<br>
<br>
The board is specifically designed for hobby electronic. Only
the blue layer is meant to be etched as a printed circuit
board. The red lines are wires. It's much easier and less
accuracy is required to build a single sided printed circuit
board. You can lay the wires (red) such that they have the
shortest length. I could not do that in eagle. <br>
<br>
The few parts in the high power part of the power supply can be
mounted on a standard prototyping boards (those boards with
many holes). The main board and the power part is connected via
wires (JP2 and JP3). You will notice that the ground wire from
the main part connects plus DC out. This is correct and it is
the reason why we need two separate transformers for (one for
the power part and one for the logic part with Microcontroller
and operational amplifiers).
<h2>How it works</h2>
Looking at the main schematic you can see that it consists of 2
logical parts. One is is marked in the schematic as "current
control" and the other "voltage control". These are 2
independent control loops. The one loop controls the output
voltage and the other the voltage drop over the 0.275 Ohm
resistor in the power part. The voltage drop is equivalent to
the current. The two control parts are "combined" via diodes D2
and D3. These diodes form and analog electrical OR-gate. That
is if the current is too high then the current control part
lowers the voltage until it is below the limit otherwise
(current not too high) the voltage control part is in charge of
regulating the output voltage. <br>
<br>
This logical OR works because the transistor T3 is connected
via R19 to +5V. If there where no operational amplifiers
connected behind D2 and D3 then you would get maximum output
power. The operational amplifiers in the control loops control
the output by taking away the +5V from T3 (pull it as much as
needed to ground). <br>
<br>
The voltage control loop controls the output voltage according
to the voltage level that it gets on pin 5 of IC6B. In other
words the voltage on pin 5 is equivalent to the output
multiplied by the amplification factor which is determined by
the resistors R15, R10 and R16. The same goes for the current
except that it is the voltage on resistor R30 which is
equivalent to the max. output current. <br>
<br>
In order to set the max current or regulate the output of the
power supply we just need to supply appropriate voltages on the
two points (pin 5 of IC6B and resistor R30). This is what the
Microcontroller does.... but how can a Microcontroller generate
and regulate a reference DC voltage? Take a look at the
following picture: <br>
<center>
<img src="../../common/images/article251/lowpass.gif" width=
"475" height="309" alt="[pwm]">
</center>
<br>
What you see in this picture is how a pulsed signal can be
transformed into a DC signal. All you need to do is run it
through a low pass filter with a cut off frequency a hundred
(or more) times lower than the signal frequency. Since our
Microcontroller runs at 4Mhz it is not so difficult to design
such a low pass filter. Even if we implement the signal
generation with software we will still get a few kHz and the
filter will still be very small. <br>
<br>
The difference in the picture between the upper and the lower
diagram is called pulse width modulation. By changing the
length of the pulses we can change the DC voltage behind the
filter. <br>
<br>
Cool, isn't it? We can generate a exact DC voltage from a
digital signal! <br>
<br>
The AT90S4433 Microcontroller has two internal counters. One is
16bit wide and one is 8bit wide. The 16bit counter has the
possibility to use pulse width modulation (PWM) which is
already implemented in hardware in the AT90S4433 chip with a
resolution of 10bit. The 8bit counter does not have that but we
can implement it in software. It is still fast enough. We use
the 16bit counter for voltage regulation this gives us
10bit=1023 steps of resolution for the voltage control. The
output current is controlled with the 8bit wide counter and it
gives us 255 steps to control 1-3000mA. That means we have an
accuracy of about 12mA (or less). This is still sufficient for
current control. <br>
<br>
All the other parts in the circuit are for power supply and
reference voltage (the 7805 is our reference point) and for
ensuring that the power supply does not behave unstable when
switched on or off.
<h2>The software</h2>
The software for the Microcontroller uses many aspects which
you already know from the previous articles (uart for rs232,
lcd display, counters in interrupt mode). You can take a look
at it here:<br>
<a href=
"../../common/src/article251/linuxdcp_c.html">linuxdcp.c</a>.
<br>
<br>
Interesting is perhaps the software PWM (Pulse Width
Modulation). The variable ipwm_phase implements together with
ipwm_h the PWM for the current. We just run the 8bit counter in
interrupt mode and every time it generates an overflow the
function "SIGNAL(SIG_OVERFLOW0)" is called. Here we check the
ipwm_phase to check if we should generate a 1 or a 0 at the
output and then we restart the timer. Easy.<br>
<br>
The software is not complicated at all but to understand it
exactly you need to read the data sheet of the 4433 (see
references). <br>
<br>
The 4433 is a 8bit Microcontroller and its mathematical
capabilities are limited. The functions divXbyY and multiXbyY
implement 24bit math which we need to accurately calculate the
pulse width from a given voltage set be the user. <br>
<br>
Our power supply has 7 buttons. 6 buttons are available to step
the current and voltage levels and one button is "standby".
Using the standby button you can temporary switch off the power
and still change the voltage and current limits. The state of
the buttons is "pulled" in the main loop in the program. The
ignorebutton variable is used to debounce the buttons. When you
press a button with your finger it bounces up and down a bit.
As a human you will not notice this but the Microcontroller is
so fast that it would see on, off, on, off... The ignorebutton
counter waits a bit after a button press to avoid this
bouncing.
<h2>Making the printed circuit board</h2>
<table align="right" width="250" border="2">
<tr>
<td>The main board:
<br>
<a href=
"../../common/images/article251/dcpower-mainbrd.jpg"><img src=
"../../common/images/article251/dcpower-mainbrd_th.jpg" width=
"200" height="167" alt="[main board]"></a> </td>
</tr>
<tr>
<td>The case for the power supply. Wood on the sides, sheet
metal for bottom part, top and front:<br>
<a href=
"../../common/images/article251/dcpower-box.jpg"><img src=
"../../common/images/article251/dcpower-box_th.jpg" width=
"236" height="158" alt="[box]"></a> </td>
</tr>
<tr>
<td>The front panel:<br>
<a href=
"../../common/images/article251/dcpower-frontpanel.jpg"><img
src=
"../../common/images/article251/dcpower-frontpanel_th.jpg"
width="243" height="99" alt="[front]"></a> </td>
</tr>
</table>
The software package contains a postscript file
(linuxDCpower.ps) for the printed circuit board. Personally I
find that the pads are always a bit too small. Therefore I
strongly recommend to enlarge them a bit with a paint marker
before you etch the board. The process how to make a board at
home is described in: <a href="../May2002/article236.shtml">May
2002, A LCD control panel for your Linux server</a>. <br>
How to build a cheap but good looking case for your power
supply is described in the <a href=
"../September2002/article253.shtml">"September 2002, Frequency
counter 1Hz-100Mhz with LCD display and RS232 interface"</a>
article. You can see the case and front panel that I made on
the right. Click on the images for bigger pictures.
<h2>Testing</h2>
Like any circuit that you have soldered together it is a good
idea to not directly connect it to full power supply but rather
test it step wise. This is to find faults that you have made
while building the circuit. <br>
<ol>
<li>Assemble the main board with all the parts but do not put
the ICs into the sockets.</li>
<li>Take a 9V battery and connect plus to the pin 2 and minus
to pin 1 on the connector marked in the schematic with
AC_POWER. Use a voltmeter and check that you have +5V on the
max232 between pin 8 and 16 and on the Microcontroller pins 7
and 8. On the operational amps you should have almost 9V on
the positive power pin.</li>
<li>Now turn the 9V battery (pin 1 to plus and pin 2 to
minus) and check that you have around -9V on the negative
power pins of the operational amps.</li>
<li>If all the tests until here are passed then the power
supply of the main board works and it is save to insert the
max 232 and the Microcontroller into their sockets.</li>
<li>Use again the 9V battery and connect is such that you
have the +5V supply working (see above). Connect the
programmer cable to the parallel port and the connector for
programming the board.<br>
Unpack the software package (for download see references
chapter), "cd" into the directory that is created and
type:<br>
make avr_led_lcd_test.hex<br>
make testload<br>
make ttydevinit<br>
<br>
Now the test software should be loaded to the board. On the
LCD display you should see "hello", the red LED should blink
and if you connect your computer to the rs232 you should see
"ok" being printed (initialize the rs232 line with
ttydevinit, then type cat /dev/ttyS0, or cat /dev/ttyS1 for
COM2).</li>
<li>Now assemble the power part but do not connect the main
transformer yet. Instead connect the 9V battery to the cables
where the transformer would be connected. No matter in which
direction the battery is connected the 4700uF capacitor
should always charge up to around 9V. Check this with a
voltmeter.</li>
<li>When the last test step is passed do some final checking
of the wires and then connect all the transformers and power
on. With no operational amplifiers in the sockets you should
get the max. output voltage out of the power supply. Measure
this but take care to not cause any short circuit otherwise
you blow up the power transistors since there is no current
limitation yet.</li>
<li>Power down insert all the operational amplifiers and
connect again the programmer cable, power on and type:<br>
make<br>
make load<br>
</li>
<li>Now the power supply should be fully functional. Note
that while the programmer cable is still connected the output
is slightly off. Disconnect it to get accurate output voltage
and current.</li>
</ol>
<h2>Here it is: Our own power supply</h2>
You have seen above that there are 3 options available
dependent on what transformer you use. The default software is
for 16V, 2.2A output. To change this edit the file <a href=
"../../common/src/article251/linuxdcp_c.html">linuxdcp.c</a>
and search for:<br>
MAX_U, IMINSTEP, MAX_I, and in the function set_i you need to
change the calibration if you have 3A maximum output. The code
is well commented and you will see what you need change. <br>
<br>
Finally here are a few pictures of the power supply as I have
build it. It was quite some work but it really is a very good
and robust power supply. The time was well invested since a
lab-power supply is really one of the most used things. <br>
<br>
<center>
<a href=
"../../common/images/article251/dcpower-final_frontview.jpg"><img
src=
"../../common/images/article251/dcpower-final_frontview_th.jpg"
width="324" height="151" alt="[front view]"></a><br>
<br>
<a href=
"../../common/images/article251/dcpower-final_topview.jpg"><img
src=
"../../common/images/article251/dcpower-final_topview_th.jpg"
width="250" height="212" alt="[top view]"></a>
</center>
<h2>Using the power supply</h2>
It is probably almost obvious how you use the power supply. You
have 4 buttons to set the output voltage. 2 buttons to step
up/down by 1V and 2 buttons to step up/down by 0.1V. The
current limit can be set also with 2 buttons. Here the stepping
is not linear. For smaller values you can increment or
decrement by 50mA. For values over 200mA you can step in 100mA
units and above 1A in 200mA units. That way it is easy to step
through the whole range with just 2 buttons. <br>
The standby button can be used to temporary switch off the
power without the need to set the values again when you switch
on. <br>
The red LED will go on when you reach the current limit and it
will blink in standby mode. <br>
The power supply can also be totally controlled via ascii
commands over the rs232 serial line. The following commands are
available:
<p class="code">u=X set the voltage (e.g u=105 set voltage to
10.5V)<br>
i=Xmax set the max current (e.g i=500 sets the current limit to
500mA)<br>
s=1 or s=0 set to standby<br>
u=? or i=? or s=? print the current settings. This will produce
a printout that looks e.g like this:<br>
u: 50 s:0 i: 100 l:0<br>
u: means voltage=50 =5V, s:0 means standby off, i: 100 is
100mA, and l:0 means current limit is not reached.</p>
Using this acsii command language you could also write a
graphical user interface for the power supply. To use the rs232
line you need to initialize it first with the command
ttydevinit. ttydevinit is included in the software package. This is
also described in the <a href=
"../September2002/article253.shtml">September 2002, Frequency
Counter article</a>.
<p>As you have seen in the schematic diagram above we use 2 transformers
and the ground plane of the control logic is connected to the positive DC
output. The two transformers separate the voltages and there is normally
no problem with this setup. We need to connect things like that to have
the right polarity for the feedback loops of the operational amplifiers.
<b>A word of waring</b>: This setup means also that the ground line of RS232 line
is connected to the positive DC output! In other words you can not use the
RS232 line if you want to use the power supply with other parts that are
connected somehow to the ground line of your computer. It might be an
idea to put a label on the case of the power supply saying "ground line of
RS232 connection is connected to positive DC output line".
If you want to make sure that there is no way to cause a short circuit
through the ground wire of the RS232 line then either
use a battery powered laptop or make sure that the ciruit powered
by the power supply does not have any other connections or do not
use the RS232 command interface. Also don't be too shocked by this
warning. If do not go above 250mA with the current limitation of
the power supply then the red led will tell you when you made a mistake
and there is no danger for your computer even if you did something stupid.
</p>
<h2>Security</h2>
This circuit contains a transformer which is connected to
then main power supply (230V or 110V dependent on your country). Please
ensure proper insulation. If you have never worked with power supplies
then ask an experienced person to check your
circuit with regards to insulation and security before you connect the
first time.
<h2>Tuning</h2>
The software for the power supply is already calibrated. Most
likely you will not have to change anything there. Hardware
wise the calibration depends only on the 7805, R15, R10, R16
and R38, R30, R26. Only those parts influence the voltage and
current levels. If you want to do fine tuning you can either
change those resistor or you can modify the software. Note that
a connected programmer cable influences the output. Before you
make measurements you should disconnect the cable. In software
you can do the changes in the functions set_u and set_i. It's
commented in the code of <a href=
"../../common/src/article251/linuxdcp_c.html">linuxdcp.c</a>
<h2>References</h2>
<ul>
<li>The uisp AVR programmer software: <a href=
"http://www.amelek.gda.pl/avr/">www.amelek.gda.pl/avr/</a><br>
local copy: <a href=
"../../common/src/article231/uisp-20011025.tar.gz">uisp-20011025.tar.gz</a></li>
<li>How to build the programmer hardware and install the AVR
compiler:<br>
<a href="../March2002/article231.shtml">March 2002,
Programming the AVR Microcontroller with GCC</a></li>
<li>The source code for this article <a href=
"../../common/src/article251/linuxdcpower-0.1.tar.gz">linuxdcpower-0.1.tar.gz,
1201K</a> . The circuit diagram, the Eagle files and screen
shoots are as well included.</li>
<li>All software (updates will be listed here) and documents
:<a href=
"../../common/src/article251/">software/datasheets</a></li>
<li>Datasheet for bd379 <a href=
"../../common/src/article251/bd379.pdf">bd379.pdf
44K</a></li>
<li>Datasheet for TL082 <a href=
"../../common/src/article251/TL071.pdf">TL082.pdf
110K</a></li>
<li>Datasheet for TL071 <a href=
"../../common/src/article251/TL071.pdf">TL071.pdf
268K</a></li>
<li>Datasheet for 2n3055 <a href=
"../../common/src/article251/2n3055.pdf">2n3055.pdf
64K</a></li>
<li>Datasheet for MAX232 <a href=
"../../common/src/article236/MAX220-MAX249.pdf">MAX220-MAX249.pdf
448K</a></li>
<li>Datasheet for ST232, a cheap variant, often sold instead
of the real MAX232 <a href=
"../../common/src/article236/st232.pdf">st232.pdf
100K</a></li>
<li>Datasheet for Atmel AT90S4433 <a href=
"../../common/src/article231/avr4433.pdf">avr4433.pdf
2356K</a></li>
<li>The atmel website: <a href=
"http://www.atmel.com/">www.atmel.com/</a></li>
<li>Eagle for Linux <a href=
"http://www.cadsoftusa.com/">cadsoftusa.com</a></li>
</ul>
<!-- vim: set sw=2 ts=2 et tw=80: -->
</body>
</html>