From david-b@pacbell.net Mon Nov 7 15:26:37 2005 Message-ID: <20051107232446.79146.qmail@web80724.mail.yahoo.com> Date: Mon, 7 Nov 2005 15:24:46 -0800 (PST) From: David Brownell Subject: USB: EHCI updates (4/4) driver model wakeup flags To: greg@kroah.com This teaches the EHCI driver to use the new driver model wakeup flags, replacing the similar ones in the HCD glue. It also adds a workaround for the current glitch whereby PCI init doesn't init the wakeup flags from the PCI PM capabilities. (EHCI controllers don't worry about legacy mode; the PCI PM capability would always do the job.) Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 2 +- drivers/usb/host/ehci-hub.c | 4 ++-- drivers/usb/host/ehci-pci.c | 11 ++++++++++- 3 files changed, 13 insertions(+), 4 deletions(-) --- gregkh-2.6.orig/drivers/usb/host/ehci-hcd.c +++ gregkh-2.6/drivers/usb/host/ehci-hcd.c @@ -624,7 +624,7 @@ static irqreturn_t ehci_irq (struct usb_ } /* remote wakeup [4.3.1] */ - if ((status & STS_PCD) && hcd->remote_wakeup) { + if ((status & STS_PCD) && device_may_wakeup(&hcd->self.root_hub->dev)) { unsigned i = HCS_N_PORTS (ehci->hcs_params); /* resume root hub? */ --- gregkh-2.6.orig/drivers/usb/host/ehci-hub.c +++ gregkh-2.6/drivers/usb/host/ehci-hub.c @@ -59,7 +59,7 @@ static int ehci_bus_suspend (struct usb_ if ((t1 & PORT_PE) && !(t1 & PORT_OWNER)) t2 |= PORT_SUSPEND; - if (hcd->remote_wakeup) + if (device_may_wakeup(&hcd->self.root_hub->dev)) t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E; else t2 &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E); @@ -517,7 +517,7 @@ static int ehci_hub_control ( if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) goto error; - if (hcd->remote_wakeup) + if (device_may_wakeup(&hcd->self.root_hub->dev)) temp |= PORT_WAKE_BITS; writel (temp | PORT_SUSPEND, &ehci->regs->port_status [wIndex]); --- gregkh-2.6.orig/drivers/usb/host/ehci-pci.c +++ gregkh-2.6/drivers/usb/host/ehci-pci.c @@ -204,7 +204,16 @@ static int ehci_pci_reset(struct usb_hcd /* Serial Bus Release Number is at PCI 0x60 offset */ pci_read_config_byte(pdev, 0x60, &ehci->sbrn); - /* REVISIT: per-port wake capability (PCI 0x62) currently unused */ + /* Workaround current PCI init glitch: wakeup bits aren't + * being set from PCI PM capability. + */ + if (!device_can_wakeup(&pdev->dev)) { + u16 port_wake; + + pci_read_config_word(pdev, 0x62, &port_wake); + if (port_wake & 0x0001) + device_init_wakeup(&pdev->dev, 1); + } retval = ehci_pci_reinit(ehci, pdev);