From khali@linux-fr.org Sun Feb 5 14:26:07 2006 Date: Sun, 5 Feb 2006 23:26:51 +0100 From: Jean Delvare To: Greg KH Subject: [PATCH 07/11] w83781d: Don't reset the chip by default Message-Id: <20060205232651.5a0be1e4.khali@linux-fr.org> Content-Disposition: inline; filename=hwmon-w83781d-no-reset-by-default.patch Stop resetting the chip on load by default, so as to preserve the BIOS initializations. Same was done in the w83627hf driver some times ago for the same reasons. Signed-off-by: Jean Delvare Signed-off-by: Greg Kroah-Hartman --- Documentation/hwmon/w83781d | 5 +++++ drivers/hwmon/w83781d.c | 22 +++++++++++++++++++++- 2 files changed, 26 insertions(+), 1 deletion(-) --- gregkh-2.6.orig/drivers/hwmon/w83781d.c +++ gregkh-2.6/drivers/hwmon/w83781d.c @@ -57,6 +57,10 @@ I2C_CLIENT_INSMOD_5(w83781d, w83782d, w8 I2C_CLIENT_MODULE_PARM(force_subclients, "List of subclient addresses: " "{bus, clientaddr, subclientaddr1, subclientaddr2}"); +static int reset; +module_param(reset, bool, 0); +MODULE_PARM_DESC(reset, "Set to one to reset chip on load"); + static int init = 1; module_param(init, bool, 0); MODULE_PARM_DESC(init, "Set to zero to bypass chip initialization"); @@ -1460,8 +1464,17 @@ w83781d_init_client(struct i2c_client *c int type = data->type; u8 tmp; - if (init && type != as99127f) { /* this resets registers we don't have + if (reset && type != as99127f) { /* this resets registers we don't have documentation for on the as99127f */ + /* Resetting the chip has been the default for a long time, + but it causes the BIOS initializations (fan clock dividers, + thermal sensor types...) to be lost, so it is now optional. + It might even go away if nobody reports it as being useful, + as I see very little reason why this would be needed at + all. */ + dev_info(&client->dev, "If reset=1 solved a problem you were " + "having, please report!\n"); + /* save these registers */ i = w83781d_read_value(client, W83781D_REG_BEEP_CONFIG); p = w83781d_read_value(client, W83781D_REG_PWMCLK12); @@ -1478,6 +1491,13 @@ w83781d_init_client(struct i2c_client *c w83781d_write_value(client, W83781D_REG_BEEP_INTS2, 0); } + /* Disable power-on abnormal beep, as advised by the datasheet. + Already done if reset=1. */ + if (init && !reset && type != as99127f) { + i = w83781d_read_value(client, W83781D_REG_BEEP_CONFIG); + w83781d_write_value(client, W83781D_REG_BEEP_CONFIG, i | 0x80); + } + data->vrm = vid_which_vrm(); if ((type != w83781d) && (type != as99127f)) { --- gregkh-2.6.orig/Documentation/hwmon/w83781d +++ gregkh-2.6/Documentation/hwmon/w83781d @@ -36,6 +36,11 @@ Module parameters Use 'init=0' to bypass initializing the chip. Try this if your computer crashes when you load the module. +* reset int + (default 0) + The driver used to reset the chip on load, but does no more. Use + 'reset=1' to restore the old behavior. Report if you need to do this. + force_subclients=bus,caddr,saddr,saddr This is used to force the i2c addresses for subclients of a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b'