From: Eric Moore After host reset, the device are programmed to default asyn narrow nego. We need to reprogram the parameter back to previous values. If the host reset is called as a result of spi_dv_device() commands timing out, its possible to get into an infinite loop of dv to host reset. This will prevent that case, as we merely program old values. If host reset is called outside context of domain validation, then we can call spi_dv_device. Please apply. Signed-off-by: Eric Moore Cc: Mark Haverkamp Cc: James Bottomley Signed-off-by: Andrew Morton --- drivers/message/fusion/mptbase.h | 1 + drivers/message/fusion/mptspi.c | 23 +++++++++++++++++++++-- 2 files changed, 22 insertions(+), 2 deletions(-) diff -puN drivers/message/fusion/mptbase.h~scsi-spi-transport-scsi-domain-validation-after-reset drivers/message/fusion/mptbase.h --- a/drivers/message/fusion/mptbase.h~scsi-spi-transport-scsi-domain-validation-after-reset +++ a/drivers/message/fusion/mptbase.h @@ -994,6 +994,7 @@ typedef struct _MPT_SCSI_HOST { int scandv_wait_done; long last_queue_full; u16 tm_iocstatus; + u16 spi_pending; struct list_head target_reset_list; } MPT_SCSI_HOST; diff -puN drivers/message/fusion/mptspi.c~scsi-spi-transport-scsi-domain-validation-after-reset drivers/message/fusion/mptspi.c --- a/drivers/message/fusion/mptspi.c~scsi-spi-transport-scsi-domain-validation-after-reset +++ a/drivers/message/fusion/mptspi.c @@ -676,7 +676,9 @@ static void mptspi_dv_device(struct _MPT return; } + hd->spi_pending |= (1 << sdev->id); spi_dv_device(sdev); + hd->spi_pending &= ~(1 << sdev->id); if (sdev->channel == 1 && mptscsih_quiesce_raid(hd, 0, vtarget->channel, vtarget->id) < 0) @@ -1202,11 +1204,27 @@ mptspi_dv_renegotiate_work(struct work_s container_of(work, struct work_queue_wrapper, work); struct _MPT_SCSI_HOST *hd = wqw->hd; struct scsi_device *sdev; + struct scsi_target *starget; + struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1; + u32 nego; kfree(wqw); - shost_for_each_device(sdev, hd->ioc->sh) - mptspi_dv_device(hd, sdev); + if (hd->spi_pending) { + shost_for_each_device(sdev, hd->ioc->sh) { + if (hd->spi_pending & (1 << sdev->id)) + continue; + starget = scsi_target(sdev); + nego = mptspi_getRP(starget); + pg1.RequestedParameters = cpu_to_le32(nego); + pg1.Reserved = 0; + pg1.Configuration = 0; + mptspi_write_spi_device_pg1(starget, &pg1); + } + } else { + shost_for_each_device(sdev, hd->ioc->sh) + mptspi_dv_device(hd, sdev); + } } static void @@ -1452,6 +1470,7 @@ mptspi_probe(struct pci_dev *pdev, const init_waitqueue_head(&hd->scandv_waitq); hd->scandv_wait_done = 0; hd->last_queue_full = 0; + hd->spi_pending = 0; /* Some versions of the firmware don't support page 0; without * that we can't get the parameters */ _