From: Jan Engelhardt Use menuconfigs instead of menus, so the whole menu can be disabled at once instead of going through all options. Signed-off-by: Jan Engelhardt Cc: Evgeniy Polyakov Signed-off-by: Andrew Morton --- drivers/w1/Kconfig | 12 ++++++------ drivers/w1/masters/Kconfig | 7 +++---- drivers/w1/slaves/Kconfig | 4 ---- 3 files changed, 9 insertions(+), 14 deletions(-) diff -puN drivers/w1/Kconfig~use-menuconfig-objects-w1 drivers/w1/Kconfig --- a/drivers/w1/Kconfig~use-menuconfig-objects-w1 +++ a/drivers/w1/Kconfig @@ -1,8 +1,6 @@ -menu "Dallas's 1-wire bus" - depends on HAS_IOMEM - -config W1 +menuconfig W1 tristate "Dallas's 1-wire support" + depends on HAS_IOMEM ---help--- Dallas' 1-wire bus is useful to connect slow 1-pin devices such as iButtons and thermal sensors. @@ -12,8 +10,10 @@ config W1 This W1 support can also be built as a module. If so, the module will be called wire.ko. +if W1 + config W1_CON - depends on CONNECTOR && W1 + depends on CONNECTOR bool "Userspace communication over connector" default y --- help --- @@ -27,4 +27,4 @@ config W1_CON source drivers/w1/masters/Kconfig source drivers/w1/slaves/Kconfig -endmenu +endif # W1 diff -puN drivers/w1/masters/Kconfig~use-menuconfig-objects-w1 drivers/w1/masters/Kconfig --- a/drivers/w1/masters/Kconfig~use-menuconfig-objects-w1 +++ a/drivers/w1/masters/Kconfig @@ -3,11 +3,10 @@ # menu "1-wire Bus Masters" - depends on W1 config W1_MASTER_MATROX tristate "Matrox G400 transport layer for 1-wire" - depends on W1 && PCI + depends on PCI help Say Y here if you want to communicate with your 1-wire devices using Matrox's G400 GPIO pins. @@ -17,7 +16,7 @@ config W1_MASTER_MATROX config W1_MASTER_DS2490 tristate "DS2490 USB <-> W1 transport layer for 1-wire" - depends on W1 && USB + depends on USB help Say Y here if you want to have a driver for DS2490 based USB <-> W1 bridges, for example DS9490*. @@ -27,7 +26,7 @@ config W1_MASTER_DS2490 config W1_MASTER_DS2482 tristate "Maxim DS2482 I2C to 1-Wire bridge" - depends on I2C && W1 && EXPERIMENTAL + depends on I2C && EXPERIMENTAL help If you say yes here you get support for the Maxim DS2482 I2C to 1-Wire bridge. diff -puN drivers/w1/slaves/Kconfig~use-menuconfig-objects-w1 drivers/w1/slaves/Kconfig --- a/drivers/w1/slaves/Kconfig~use-menuconfig-objects-w1 +++ a/drivers/w1/slaves/Kconfig @@ -3,25 +3,21 @@ # menu "1-wire Slaves" - depends on W1 config W1_SLAVE_THERM tristate "Thermal family implementation" - depends on W1 help Say Y here if you want to connect 1-wire thermal sensors to your wire. config W1_SLAVE_SMEM tristate "Simple 64bit memory family implementation" - depends on W1 help Say Y here if you want to connect 1-wire simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire. config W1_SLAVE_DS2433 tristate "4kb EEPROM family support (DS2433)" - depends on W1 help Say Y here if you want to use a 1-wire 4kb EEPROM family device (DS2433). _