From: "Antonino A. Daplas" There are a few nvidia hardware where the i2c port assignments are reversed, i.e., the 1st i2c port is assigned to the secondary display and the 2nd i2c port to the primary display. In most cases, if only 1 display is attached, or if only 1 flatpanel and 1 analog display is attached, the port reversal is of no consequence. However if 2 flatpanels are attached, it can cause display problems. There is no sane way of determining if the hardware reversed the i2c port assignment, so the simplest fix is to add a boot/module option, "reverse_i2c to explicitly reverse the i2c port. This also restores i2c ordering back to the pre-2.6.22 state. Signed-off-by: Antonino Daplas Signed-off-by: Andrew Morton --- drivers/video/nvidia/nv_i2c.c | 8 ++++---- drivers/video/nvidia/nv_type.h | 1 + drivers/video/nvidia/nvidia.c | 6 ++++++ 3 files changed, 11 insertions(+), 4 deletions(-) diff -puN drivers/video/nvidia/nv_i2c.c~nvidiafb-add-boot-option-to-reverse-i2c-port-assignment drivers/video/nvidia/nv_i2c.c --- a/drivers/video/nvidia/nv_i2c.c~nvidiafb-add-boot-option-to-reverse-i2c-port-assignment +++ a/drivers/video/nvidia/nv_i2c.c @@ -125,11 +125,11 @@ void nvidia_create_i2c_busses(struct nvi par->chan[1].par = par; par->chan[2].par = par; - par->chan[0].ddc_base = 0x36; - nvidia_setup_i2c_bus(&par->chan[0], "nvidia #0", I2C_CLASS_HWMON); + par->chan[0].ddc_base = (par->reverse_i2c) ? 0x36 : 0x3e; + nvidia_setup_i2c_bus(&par->chan[0], "nvidia #0", 0); - par->chan[1].ddc_base = 0x3e; - nvidia_setup_i2c_bus(&par->chan[1], "nvidia #1", 0); + par->chan[1].ddc_base = (par->reverse_i2c) ? 0x3e : 0x36; + nvidia_setup_i2c_bus(&par->chan[1], "nvidia #1", I2C_CLASS_HWMON); par->chan[2].ddc_base = 0x50; nvidia_setup_i2c_bus(&par->chan[2], "nvidia #2", 0); diff -puN drivers/video/nvidia/nv_type.h~nvidiafb-add-boot-option-to-reverse-i2c-port-assignment drivers/video/nvidia/nv_type.h --- a/drivers/video/nvidia/nv_type.h~nvidiafb-add-boot-option-to-reverse-i2c-port-assignment +++ a/drivers/video/nvidia/nv_type.h @@ -135,6 +135,7 @@ struct nvidia_par { int paneltweak; int LVDS; int pm_state; + int reverse_i2c; u32 crtcSync_read; u32 fpSyncs; u32 dmaPut; diff -puN drivers/video/nvidia/nvidia.c~nvidiafb-add-boot-option-to-reverse-i2c-port-assignment drivers/video/nvidia/nvidia.c --- a/drivers/video/nvidia/nvidia.c~nvidiafb-add-boot-option-to-reverse-i2c-port-assignment +++ a/drivers/video/nvidia/nvidia.c @@ -79,6 +79,7 @@ static int noscale __devinitdata = 0; static int paneltweak __devinitdata = 0; static int vram __devinitdata = 0; static int bpp __devinitdata = 8; +static int reverse_i2c __devinitdata; #ifdef CONFIG_MTRR static int nomtrr __devinitdata = 0; #endif @@ -1305,6 +1306,7 @@ static int __devinit nvidiafb_probe(stru par->CRTCnumber = forceCRTC; par->FpScale = (!noscale); par->paneltweak = paneltweak; + par->reverse_i2c = reverse_i2c; /* enable IO and mem if not already done */ pci_read_config_word(pd, PCI_COMMAND, &cmd); @@ -1486,6 +1488,8 @@ static int __devinit nvidiafb_setup(char noaccel = 1; } else if (!strncmp(this_opt, "noscale", 7)) { noscale = 1; + } else if (!strncmp(this_opt, "reverse_i2c", 11)) { + reverse_i2c = 1; } else if (!strncmp(this_opt, "paneltweak:", 11)) { paneltweak = simple_strtoul(this_opt+11, NULL, 0); } else if (!strncmp(this_opt, "vram:", 5)) { @@ -1582,6 +1586,8 @@ MODULE_PARM_DESC(mode_option, "Specify i module_param(bpp, int, 0); MODULE_PARM_DESC(bpp, "pixel width in bits" "(default=8)"); +module_param(reverse_i2c, int, 0); +MODULE_PARM_DESC(reverse_i2c, "reverse port assignment of the i2c bus"); #ifdef CONFIG_MTRR module_param(nomtrr, bool, 0); MODULE_PARM_DESC(nomtrr, "Disables MTRR support (0 or 1=disabled) " _