From 1309e617bc56f2f8af9a9c5aab1224a45539002a Mon Sep 17 00:00:00 2001 From: Maurice Dawson Date: Sat, 26 Jun 2010 17:02:25 +0100 Subject: [PATCH 252/524] Staging: comedi: fix over 80 character coding style issue in ni_labpc.c This is a patch to the ni_labpc.c file that fixes up 80 character warnings found by the checkpatch.pl tool Signed-off-by: Maurice Dawson Signed-off-by: Greg Kroah-Hartman --- drivers/staging/comedi/drivers/ni_labpc.c | 38 ++++++++++++++++++++++------ 1 files changed, 30 insertions(+), 8 deletions(-) diff --git a/drivers/staging/comedi/drivers/ni_labpc.c b/drivers/staging/comedi/drivers/ni_labpc.c index 170bab6..3acf7e6 100644 --- a/drivers/staging/comedi/drivers/ni_labpc.c +++ b/drivers/staging/comedi/drivers/ni_labpc.c @@ -1098,7 +1098,10 @@ static int labpc_ai_cmdtest(struct comedi_device *dev, err++; } break; - /* TRIG_EXT doesn't care since it doesn't trigger off a numbered channel */ + /* + * TRIG_EXT doesn't care since it doesn't + * trigger off a numbered channel + */ default: break; } @@ -1156,25 +1159,35 @@ static int labpc_ai_cmd(struct comedi_device *dev, struct comedi_subdevice *s) /* setup hardware conversion counter */ if (cmd->stop_src == TRIG_EXT) { - /* load counter a1 with count of 3 (pc+ manual says this is minimum allowed) using mode 0 */ + /* + * load counter a1 with count of 3 + * (pc+ manual says this is minimum allowed) using mode 0 + */ ret = labpc_counter_load(dev, dev->iobase + COUNTER_A_BASE_REG, 1, 3, 0); if (ret < 0) { comedi_error(dev, "error loading counter a1"); return -1; } - } else /* otherwise, just put a1 in mode 0 with no count to set its output low */ + } else /* + * otherwise, just put a1 in mode 0 + * with no count to set its output low + */ devpriv->write_byte(INIT_A1_BITS, dev->iobase + COUNTER_A_CONTROL_REG); /* figure out what method we will use to transfer data */ if (devpriv->dma_chan && /* need a dma channel allocated */ - /* dma unsafe at RT priority, and too much setup time for TRIG_WAKE_EOS for */ + /* + * dma unsafe at RT priority, + * and too much setup time for TRIG_WAKE_EOS for + */ (cmd->flags & (TRIG_WAKE_EOS | TRIG_RT)) == 0 && /* only available on the isa boards */ thisboard->bustype == isa_bustype) { xfer = isa_dma_transfer; - } else if (thisboard->register_layout == labpc_1200_layout && /* pc-plus has no fifo-half full interrupt */ + /* pc-plus has no fifo-half full interrupt */ + } else if (thisboard->register_layout == labpc_1200_layout && /* wake-end-of-scan should interrupt on fifo not empty */ (cmd->flags & TRIG_WAKE_EOS) == 0 && /* make sure we are taking more than just a few points */ @@ -1621,7 +1634,10 @@ static int labpc_ai_rinsn(struct comedi_device *dev, struct comedi_subdevice *s, devpriv->command4_bits |= ADC_DIFF_BIT; devpriv->write_byte(devpriv->command4_bits, dev->iobase + COMMAND4_REG); - /* initialize pacer counter output to make sure it doesn't cause any problems */ + /* + * initialize pacer counter output to make sure it doesn't + * cause any problems + */ devpriv->write_byte(INIT_A0_BITS, dev->iobase + COUNTER_A_CONTROL_REG); labpc_clear_adc_fifo(dev); @@ -1846,7 +1862,10 @@ static void labpc_adc_timing(struct comedi_device *dev, struct comedi_cmd *cmd) unsigned int scan_period; scan_period = labpc_ai_scan_period(cmd); - /* calculate cascaded counter values that give desired scan timing */ + /* + * calculate cascaded counter values + * that give desired scan timing + */ i8253_cascade_ns_to_timer_2div(LABPC_TIMER_BASE, &(devpriv->divisor_b1), &(devpriv->divisor_b0), @@ -1857,7 +1876,10 @@ static void labpc_adc_timing(struct comedi_device *dev, struct comedi_cmd *cmd) unsigned int convert_period; convert_period = labpc_ai_convert_period(cmd); - /* calculate cascaded counter values that give desired conversion timing */ + /* + * calculate cascaded counter values + * that give desired conversion timing + */ i8253_cascade_ns_to_timer_2div(LABPC_TIMER_BASE, &(devpriv->divisor_a0), &(devpriv->divisor_b0), -- 1.7.1