[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 2.6.38-rc5-dt6+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #760 SMP Tue Feb 22 09:19:19 CST 2011 [ 0.000000] Command line: run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk panic=10 hung_task_panic=1 softlockup_panic=1 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.11/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcde3000 (usable) [ 0.000000] BIOS-e820: 00000000bcde3000 - 00000000bcffb000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcffb000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf800000 [ 0.000000] 0000000000 - 00bf800000 page 4k [ 0.000000] kernel direct mapping tables up to bf800000 @ 1fa00000-20000000 [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110112/tbfadt-557) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110112/tbfadt-607) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fc000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-00000000bf800000 [ 0.000000] Initmem setup node 0 0000000000000000-00000000bf800000 [ 0.000000] NODE_DATA [00000000bcdde000 - 00000000bcde2fff] [ 0.000000] [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800b9400000-ffff8800bbdfffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x000bcde3 [ 0.000000] 0: 0x000bcffb -> 0x000bf6bd [ 0.000000] 0: 0x000bf6bf -> 0x000bf714 [ 0.000000] 0: 0x000bf7bf -> 0x000bf7e7 [ 0.000000] 0: 0x000bf7ff -> 0x000bf800 [ 0.000000] On node 0 totalpages: 783535 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 6 pages reserved [ 0.000000] DMA zone: 3918 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 10668 pages used for memmap [ 0.000000] DMA32 zone: 768887 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fc000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fb000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bcde3000 - 00000000bcffb000 [ 0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7400000 s1916224 r8192 d21184 u2097152 [ 0.000000] pcpu-alloc: s1916224 r8192 d21184 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 772805 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk panic=10 hung_task_panic=1 softlockup_panic=1 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.11/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] log_buf_len: 8388608 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Memory: 3015844k/3137536k available (11127k kernel code, 3396k absent, 118296k reserved, 5792k data, 2936k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:4352 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6335 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 31457280 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] ODEBUG: 23 of 23 active objects replaced [ 0.004000] Fast TSC calibration using PIT [ 0.008000] Detected 3200.006 MHz processor. [ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 6400.01 BogoMIPS (lpj=12800024) [ 0.000536] pid_max: default: 32768 minimum: 301 [ 0.001566] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003448] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.004368] Mount-cache hash table entries: 256 [ 0.004911] Initializing cgroup subsys debug [ 0.005134] Initializing cgroup subsys ns [ 0.005346] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. [ 0.005769] Initializing cgroup subsys cpuacct [ 0.006004] Initializing cgroup subsys memory [ 0.006252] Initializing cgroup subsys devices [ 0.006481] Initializing cgroup subsys freezer [ 0.006709] Initializing cgroup subsys blkio [ 0.006987] CPU: Physical Processor ID: 0 [ 0.007199] CPU: Processor Core ID: 0 [ 0.007400] mce: CPU supports 9 MCE banks [ 0.007618] CPU0: Thermal monitoring enabled (TM1) [ 0.007869] using mwait in idle threads. [ 0.008949] ACPI: Core revision 20110112 [ 0.022790] ftrace: allocating 34979 entries in 138 pages [ 0.031374] Getting VERSION: 60015 [ 0.031565] Getting VERSION: 60015 [ 0.031754] Getting ID: 0 [ 0.031914] Getting ID: 0 [ 0.032074] Setting APIC routing to physical flat [ 0.032322] enabled ExtINT on CPU#0 [ 0.032671] ESR value before enabling vector: 0x00000040 after: 0x00000000 [ 0.032991] ENABLING IO-APIC IRQs [ 0.033177] init IO_APIC IRQs [ 0.033350] 8-0 (apicid-pin) not connected [ 0.033607] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0) [ 0.033978] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0) [ 0.034347] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) [ 0.034714] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0) [ 0.035083] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0) [ 0.035453] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0) [ 0.035820] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0) [ 0.036188] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0) [ 0.036560] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0) [ 0.036928] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0) [ 0.037303] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0) [ 0.037677] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0) [ 0.038050] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0) [ 0.038425] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0) [ 0.039362] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0) [ 0.039734] 8-16 8-17 8-18 8-19 8-20 8-21 8-22 8-23 (apicid-pin) not connected [ 0.040500] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.080344] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.080738] Using local APIC timer interrupts. [ 0.080739] calibrating APIC timer ... [ 0.187787] ... lapic delta = 833407 [ 0.187983] ... PM-Timer delta = 357974 [ 0.188187] ... PM-Timer result ok [ 0.188377] ..... delta 833407 [ 0.188553] ..... mult: 35792321 [ 0.188735] ..... calibration result: 533380 [ 0.188957] ..... CPU clock speed is 3200.1152 MHz. [ 0.189200] ..... host bus clock speed is 133.1380 MHz. [ 0.189466] Performance Events: PEBS fmt1+, Nehalem events, Intel PMU driver. [ 0.189895] ... version: 3 [ 0.190106] ... bit width: 48 [ 0.190320] ... generic registers: 4 [ 0.190532] ... value mask: 0000ffffffffffff [ 0.190791] ... max period: 000000007fffffff [ 0.191050] ... fixed-purpose events: 3 [ 0.191261] ... event mask: 000000070000000f [ 0.191946] lockdep: fixing up alternatives. [ 0.192233] Booting Node 0, Processors #1masked ExtINT on CPU#1 [ 0.301439] lockdep: fixing up alternatives. [ 0.301718] #2masked ExtINT on CPU#2 [ 0.409098] lockdep: fixing up alternatives. [ 0.409349] #3masked ExtINT on CPU#3 [ 0.516725] lockdep: fixing up alternatives. [ 0.516976] #4masked ExtINT on CPU#4 [ 0.624414] lockdep: fixing up alternatives. [ 0.624664] #5masked ExtINT on CPU#5 [ 0.732145] lockdep: fixing up alternatives. [ 0.732397] #6masked ExtINT on CPU#6 [ 0.839776] lockdep: fixing up alternatives. [ 0.840027] #7masked ExtINT on CPU#7 [ 0.947270] Brought up 8 CPUs [ 0.947447] Total of 8 processors activated (51202.53 BogoMIPS). [ 0.950661] CPU0 attaching sched-domain: [ 0.950874] domain 0: span 0,4 level SIBLING [ 0.951142] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 0.951584] domain 1: span 0-7 level MC [ 0.951829] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.952608] CPU1 attaching sched-domain: [ 0.952816] domain 0: span 1,5 level SIBLING [ 0.953074] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 0.953516] domain 1: span 0-7 level MC [ 0.953761] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.954537] CPU2 attaching sched-domain: [ 0.954745] domain 0: span 2,6 level SIBLING [ 0.955003] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 0.955449] domain 1: span 0-7 level MC [ 0.955693] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.956471] CPU3 attaching sched-domain: [ 0.956680] domain 0: span 3,7 level SIBLING [ 0.956938] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 0.957379] domain 1: span 0-7 level MC [ 0.957623] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.958402] CPU4 attaching sched-domain: [ 0.958610] domain 0: span 0,4 level SIBLING [ 0.958868] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 0.959313] domain 1: span 0-7 level MC [ 0.959558] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.960335] CPU5 attaching sched-domain: [ 0.960544] domain 0: span 1,5 level SIBLING [ 0.960802] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 0.961244] domain 1: span 0-7 level MC [ 0.961489] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.962268] CPU6 attaching sched-domain: [ 0.962477] domain 0: span 2,6 level SIBLING [ 0.962735] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 0.963180] domain 1: span 0-7 level MC [ 0.963424] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.964201] CPU7 attaching sched-domain: [ 0.964409] domain 0: span 3,7 level SIBLING [ 0.964667] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 0.965109] domain 1: span 0-7 level MC [ 0.965353] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.966606] kworker/u:0 used greatest stack depth: 5320 bytes left [ 0.969447] xor: automatically using best checksumming function: generic_sse [ 0.987015] generic_sse: 11972.000 MB/sec [ 0.987238] xor: using function: generic_sse (11972.000 MB/sec) [ 0.987596] Time: 11:11:03 Date: 02/22/11 [ 0.987919] NET: Registered protocol family 16 [ 0.988833] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.989211] ACPI: bus type pci registered [ 0.989590] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.990029] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 1.004132] PCI: Using configuration type 1 for base access [ 1.028152] bio: create slab at 0 [ 1.094682] raid6: int64x1 2648 MB/s [ 1.162472] raid6: int64x2 3090 MB/s [ 1.230262] raid6: int64x4 2594 MB/s [ 1.298049] raid6: int64x8 2593 MB/s [ 1.365848] raid6: sse2x1 7889 MB/s [ 1.433632] raid6: sse2x2 9213 MB/s [ 1.501426] raid6: sse2x4 10451 MB/s [ 1.501628] raid6: using algorithm sse2x4 (10451 MB/s) [ 1.506035] ACPI: EC: Look up EC in DSDT [ 1.534304] ACPI: Interpreter enabled [ 1.534505] ACPI: (supports S0 S1 S3 S4 S5) [ 1.534936] ACPI: Using IOAPIC for interrupt routing [ 1.561639] ACPI: No dock devices found. [ 1.561850] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.563134] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 1.565167] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 1.565483] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 1.565791] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.566155] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 1.566520] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 1.566884] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 1.567273] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 1.567624] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 1.567962] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.568253] pci 0000:00:01.0: PME# disabled [ 1.568496] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 1.568834] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 1.569123] pci 0000:00:03.0: PME# disabled [ 1.569371] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 1.569710] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 1.570000] pci 0000:00:07.0: PME# disabled [ 1.570247] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 1.570604] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 1.570960] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 1.571315] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 1.571671] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 1.572023] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 1.572384] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 1.572685] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 1.572981] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 1.573282] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 1.573602] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.573893] pci 0000:00:19.0: PME# disabled [ 1.574129] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 1.574462] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 1.574782] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 1.575116] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 1.575431] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 1.575765] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 1.576091] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 1.576394] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 1.576766] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 1.577058] pci 0000:00:1a.7: PME# disabled [ 1.577304] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 1.577603] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 1.577980] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.578270] pci 0000:00:1b.0: PME# disabled [ 1.578511] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 1.578862] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.579153] pci 0000:00:1c.0: PME# disabled [ 1.579394] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 1.579743] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.580035] pci 0000:00:1c.1: PME# disabled [ 1.580280] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 1.580630] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.580921] pci 0000:00:1c.4: PME# disabled [ 1.581166] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 1.581504] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 1.581824] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 1.582158] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 1.582475] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 1.582809] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 1.583135] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 1.583439] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 1.583810] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 1.584102] pci 0000:00:1d.7: PME# disabled [ 1.584339] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 1.584692] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 1.585649] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 1.585939] pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO [ 1.586327] pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO [ 1.586656] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 1.587032] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 1.587451] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 1.587753] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 1.588023] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 1.588294] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 1.588565] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 1.588836] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 1.589106] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 1.589436] pci 0000:00:1f.2: PME# supported from D3hot [ 1.589694] pci 0000:00:1f.2: PME# disabled [ 1.589931] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 1.590229] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 1.590562] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 1.590899] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.591157] pci 0000:00:01.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.591483] pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.591866] pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.592315] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 1.592608] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 1.592904] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 1.593250] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 1.593577] pci 0000:02:00.0: supports D1 D2 [ 1.593821] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 1.594114] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 1.594468] pci 0000:02:00.1: supports D1 D2 [ 1.594706] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.594965] pci 0000:00:03.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.595291] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.595608] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.596031] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.596289] pci 0000:00:07.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.596614] pci 0000:00:07.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.596997] pci 0000:00:07.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.597449] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.597708] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.598034] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.598419] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.598863] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.599122] pci 0000:00:1c.1: bridge window [io 0xf000-0x0000] (disabled) [ 1.599448] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.599834] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.600303] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 1.600607] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 1.600885] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 1.601166] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 1.601446] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 1.601724] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 1.602002] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 1.602353] pci 0000:06:00.0: supports D1 [ 1.602565] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 1.602845] pci 0000:06:00.0: PME# disabled [ 1.603082] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.603341] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.603632] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.603950] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.604389] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 1.604691] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 1.604990] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 1.605356] pci 0000:07:03.0: supports D1 D2 [ 1.605578] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 1.605875] pci 0000:07:03.0: PME# disabled [ 1.606146] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 1.606472] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.606797] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.607116] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.607512] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.607898] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.608285] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.608697] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 1.609110] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 1.609530] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 1.609977] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.611682] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 1.612340] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 1.612760] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 1.613186] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 1.613606] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 1.614024] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 1.614456] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 1.644579] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.645517] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.646443] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.647371] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.648298] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.649232] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.650158] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.651084] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.652177] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.652577] vgaarb: loaded [ 1.653188] SCSI subsystem initialized [ 1.653543] libata version 3.00 loaded. [ 1.653989] usbcore: registered new interface driver usbfs [ 1.654311] usbcore: registered new interface driver hub [ 1.654639] usbcore: registered new device driver usb [ 1.655448] wmi: Mapper loaded [ 1.655691] Advanced Linux Sound Architecture Driver Version 1.0.23. [ 1.655990] PCI: Using ACPI for IRQ routing [ 1.656208] PCI: pci_cache_line_size set to 64 bytes [ 1.656637] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 1.656899] reserve RAM buffer: 00000000bcde3000 - 00000000bfffffff [ 1.657239] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff [ 1.657573] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff [ 1.657907] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff [ 1.658239] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff [ 1.658875] [ 1.658876] printing PIC contents [ 1.659253] ... PIC IMR: ffff [ 1.659431] ... PIC IRR: 0c21 [ 1.659614] ... PIC ISR: 0000 [ 1.659791] ... PIC ELCR: 0c20 [ 1.659968] printing local APIC contents on CPU#0/0: [ 1.660214] ... APIC ID: 00000000 (0) [ 1.660429] ... APIC VERSION: 00060015 [ 1.660631] ... APIC TASKPRI: 00000000 (00) [ 1.660849] ... APIC PROCPRI: 00000000 [ 1.661051] ... APIC LDR: 01000000 [ 1.661239] ... APIC DFR: ffffffff [ 1.661428] ... APIC SPIV: 000001ff [ 1.661620] ... APIC ISR field: [ 1.661800] 0000000000000000000000000000000000000000000000000000000000000000 [ 1.662389] ... APIC TMR field: [ 1.662568] 0000000000000000000000000000000000000000000000000000000000000000 [ 1.663156] ... APIC IRR field: [ 1.663335] 0000000000000000000000000000000000000000000000000000000000008000 [ 1.663923] ... APIC ESR: 00000000 [ 1.664112] ... APIC ICR: 000000fc [ 1.664301] ... APIC ICR2: 07000000 [ 1.664494] ... APIC LVTT: 000200ef [ 1.664686] ... APIC LVTPC: 00000400 [ 1.664882] ... APIC LVT0: 00010700 [ 1.665075] ... APIC LVT1: 00000400 [ 1.665268] ... APIC LVTERR: 000000fe [ 1.665466] ... APIC TMICT: 00008238 [ 1.665661] ... APIC TMCCT: 00006a9a [ 1.665857] ... APIC TDCR: 00000003 [ 1.666049] [ 1.666174] number of MP IRQ sources: 15. [ 1.666386] number of IO-APIC #8 registers: 24. [ 1.666617] testing the IO APIC....................... [ 1.666876] [ 1.666995] IO APIC #8...... [ 1.667166] .... register #00: 08000000 [ 1.667371] ....... : physical APIC id: 08 [ 1.667595] ....... : Delivery Type: 0 [ 1.667807] ....... : LTS : 0 [ 1.668018] .... register #01: 00170020 [ 1.668224] ....... : max redirection entries: 0017 [ 1.669053] ....... : PRQ implemented: 0 [ 1.669275] ....... : IO APIC version: 0020 [ 1.669505] .... IRQ redirection table: [ 1.669710] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 1.669979] 00 000 1 0 0 0 0 0 0 00 [ 1.670272] 01 000 0 0 0 0 0 0 0 31 [ 1.670564] 02 000 0 0 0 0 0 0 0 30 [ 1.670856] 03 000 0 0 0 0 0 0 0 33 [ 1.671149] 04 000 0 0 0 0 0 0 0 34 [ 1.671442] 05 000 0 0 0 0 0 0 0 35 [ 1.671734] 06 000 0 0 0 0 0 0 0 36 [ 1.672026] 07 000 0 0 0 0 0 0 0 37 [ 1.672319] 08 000 0 0 0 0 0 0 0 38 [ 1.672611] 09 000 0 1 0 0 0 0 0 39 [ 1.672903] 0a 000 0 0 0 0 0 0 0 3A [ 1.673200] 0b 000 0 0 0 0 0 0 0 3B [ 1.673492] 0c 000 0 0 0 0 0 0 0 3C [ 1.673785] 0d 000 0 0 0 0 0 0 0 3D [ 1.674077] 0e 000 0 0 0 0 0 0 0 3E [ 1.674369] 0f 000 0 0 0 0 0 0 0 3F [ 1.674662] 10 000 1 0 0 0 0 0 0 00 [ 1.674954] 11 000 1 0 0 0 0 0 0 00 [ 1.675246] 12 000 1 0 0 0 0 0 0 00 [ 1.675538] 13 000 1 0 0 0 0 0 0 00 [ 1.675830] 14 000 1 0 0 0 0 0 0 00 [ 1.676123] 15 000 1 0 0 0 0 0 0 00 [ 1.676415] 16 000 1 0 0 0 0 0 0 00 [ 1.676708] 17 000 1 0 0 0 0 0 0 00 [ 1.677001] IRQ to pin mappings: [ 1.677184] IRQ0 -> 0:2 [ 1.677404] IRQ1 -> 0:1 [ 1.677626] IRQ3 -> 0:3 [ 1.677846] IRQ4 -> 0:4 [ 1.678066] IRQ5 -> 0:5 [ 1.678286] IRQ6 -> 0:6 [ 1.678506] IRQ7 -> 0:7 [ 1.678726] IRQ8 -> 0:8 [ 1.678945] IRQ9 -> 0:9 [ 1.679165] IRQ10 -> 0:10 [ 1.679392] IRQ11 -> 0:11 [ 1.679618] IRQ12 -> 0:12 [ 1.679844] IRQ13 -> 0:13 [ 1.680070] IRQ14 -> 0:14 [ 1.680297] IRQ15 -> 0:15 [ 1.680524] .................................... done. [ 1.680852] hpet clockevent registered [ 1.681064] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 1.681390] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 1.681810] hpet0: 4 comparators, 64-bit 14.318180 MHz counter [ 1.705044] Switching to clocksource hpet [ 1.708856] Switched to NOHz mode on CPU #0 [ 1.708901] Switched to NOHz mode on CPU #3 [ 1.708918] Switched to NOHz mode on CPU #4 [ 1.708943] Switched to NOHz mode on CPU #2 [ 1.708949] Switched to NOHz mode on CPU #1 [ 1.708962] Switched to NOHz mode on CPU #6 [ 1.708979] Switched to NOHz mode on CPU #7 [ 1.708986] Switched to NOHz mode on CPU #5 [ 1.734551] pnp: PnP ACPI init [ 1.734756] ACPI: bus type pnp registered [ 1.735841] pnp 00:00: [bus 00-3d] [ 1.736032] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.736247] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.736486] pnp 00:00: [io 0x0d00-0xffff window] [ 1.736723] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.736986] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 1.737260] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 1.737524] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 1.737787] pnp 00:00: [mem 0x00000000 window] [ 1.738163] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 1.738823] pnp 00:01: [io 0x0000-0x000f] [ 1.739039] pnp 00:01: [io 0x0081-0x0083] [ 1.739255] pnp 00:01: [io 0x0087] [ 1.739448] pnp 00:01: [io 0x0089-0x008b] [ 1.739663] pnp 00:01: [io 0x008f] [ 1.739856] pnp 00:01: [io 0x00c0-0x00df] [ 1.740071] pnp 00:01: [dma 4] [ 1.740355] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.740678] pnp 00:02: [io 0x0070-0x0071] [ 1.740894] pnp 00:02: [io 0x0074-0x0077] [ 1.741123] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0) [ 1.741493] pnp 00:02: [irq 8] [ 1.741779] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.742108] pnp 00:03: [io 0x00f0] [ 1.742303] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0) [ 1.742677] pnp 00:03: [irq 13] [ 1.742959] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.743287] pnp 00:04: [io 0x0061] [ 1.743587] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.743912] pnp 00:05: [io 0x0500-0x053f] [ 1.744128] pnp 00:05: [io 0x0400-0x047f] [ 1.744342] pnp 00:05: [io 0x0092] [ 1.744535] pnp 00:05: [io 0x0680-0x06ff] [ 1.744750] pnp 00:05: [io 0x0010-0x001f] [ 1.744966] pnp 00:05: [io 0x0072-0x0073] [ 1.745190] pnp 00:05: [io 0x0080] [ 1.745382] pnp 00:05: [io 0x0084-0x0086] [ 1.745597] pnp 00:05: [io 0x0088] [ 1.745789] pnp 00:05: [io 0x008c-0x008e] [ 1.746004] pnp 00:05: [io 0x0090-0x009f] [ 1.746401] system 00:05: [io 0x0500-0x053f] has been reserved [ 1.746685] system 00:05: [io 0x0400-0x047f] has been reserved [ 1.746967] system 00:05: [io 0x0680-0x06ff] has been reserved [ 1.747251] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.747664] pnp 00:06: [io 0x0060] [ 1.747857] pnp 00:06: [io 0x0064] [ 1.748210] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.749203] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 1.749565] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 1.750029] pnp: PnP ACPI: found 8 devices [ 1.750244] ACPI: ACPI bus type pnp unregistered [ 1.761237] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 1.761713] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.761970] pci 0000:00:01.0: bridge window [io disabled] [ 1.762245] pci 0000:00:01.0: bridge window [mem disabled] [ 1.762520] pci 0000:00:01.0: bridge window [mem pref disabled] [ 1.762815] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 1.763178] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.763435] pci 0000:00:03.0: bridge window [io disabled] [ 1.763710] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.764026] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.764411] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.764668] pci 0000:00:07.0: bridge window [io disabled] [ 1.764943] pci 0000:00:07.0: bridge window [mem disabled] [ 1.765225] pci 0000:00:07.0: bridge window [mem pref disabled] [ 1.765518] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.765773] pci 0000:00:1c.0: bridge window [io disabled] [ 1.766049] pci 0000:00:1c.0: bridge window [mem disabled] [ 1.766324] pci 0000:00:1c.0: bridge window [mem pref disabled] [ 1.766617] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.766874] pci 0000:00:1c.1: bridge window [io disabled] [ 1.767149] pci 0000:00:1c.1: bridge window [mem disabled] [ 1.767424] pci 0000:00:1c.1: bridge window [mem pref disabled] [ 1.767717] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.767974] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.768267] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.768583] pci 0000:00:1c.4: bridge window [mem pref disabled] [ 1.768876] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 1.769138] pci 0000:00:1e.0: bridge window [io disabled] [ 1.769414] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.769730] pci 0000:00:1e.0: bridge window [mem pref disabled] [ 1.770037] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1) [ 1.770411] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.770725] pci 0000:00:01.0: setting latency timer to 64 [ 1.770993] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.771305] pci 0000:00:03.0: setting latency timer to 64 [ 1.771573] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.771886] pci 0000:00:07.0: setting latency timer to 64 [ 1.772161] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1) [ 1.772533] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.772847] pci 0000:00:1c.0: setting latency timer to 64 [ 1.773123] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 1.773438] pci 0000:00:1c.1: setting latency timer to 64 [ 1.773706] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.774019] pci 0000:00:1c.4: setting latency timer to 64 [ 1.774288] pci 0000:00:1e.0: setting latency timer to 64 [ 1.774552] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.774821] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.775090] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.775385] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.775679] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.775974] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.776270] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 1.776564] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.776927] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 1.777202] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 1.777497] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 1.777792] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 1.778061] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 1.778331] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 1.778626] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.778920] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.779786] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.780208] NET: Registered protocol family 2 [ 1.780770] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.783063] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.786656] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) [ 1.789299] TCP: Hash tables configured (established 524288 bind 65536) [ 1.789625] TCP reno registered [ 1.789872] UDP hash table entries: 2048 (order: 6, 393216 bytes) [ 1.790372] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes) [ 1.791053] NET: Registered protocol family 1 [ 1.791525] RPC: Registered udp transport module. [ 1.791764] RPC: Registered tcp transport module. [ 1.792001] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.792344] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.792649] pci 0000:00:1a.0: Performing full reset [ 1.792909] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.793221] pci 0000:00:1a.1: Performing full reset [ 1.793481] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.793785] pci 0000:00:1a.2: Performing full reset [ 1.794194] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.794499] pci 0000:00:1d.0: Performing full reset [ 1.794759] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.795063] pci 0000:00:1d.1: Performing full reset [ 1.795323] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.795627] pci 0000:00:1d.2: Performing full reset [ 1.796028] pci 0000:02:00.0: Boot video device [ 1.796271] PCI: CLS 64 bytes, default 64 [ 1.800194] Machine check injector initialized [ 1.802005] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 1.802290] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 1.802576] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 1.802860] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 1.803144] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 1.803431] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 1.803714] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 1.803996] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 1.804350] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 1.804770] Scanning for low memory corruption every 60 seconds [ 1.805505] audit: initializing netlink socket (disabled) [ 1.805800] type=2000 audit(1298373063.588:1): initialized [ 1.818197] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.819984] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.820612] fuse init (API version 7.16) [ 1.821021] JFS: nTxBlock = 8192, nTxLock = 65536 [ 1.824419] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.825710] Btrfs loaded [ 1.825879] msgmni has been set to 5890 [ 1.826921] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.827295] io scheduler noop registered [ 1.827505] io scheduler deadline registered [ 1.827774] io scheduler cfq registered (default) [ 1.828398] pcieport 0000:00:1c.0: setting latency timer to 64 [ 1.828729] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 1.829127] pcieport 0000:00:1c.1: setting latency timer to 64 [ 1.829455] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 1.829837] pcieport 0000:00:1c.4: setting latency timer to 64 [ 1.830163] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 1.830734] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.831522] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 1.900619] ACPI: Sleep Button [SLPB] [ 1.900958] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.901328] ACPI: Power Button [PWRF] [ 1.902293] ACPI: acpi_idle registered with cpuidle [ 1.903043] Monitor-Mwait will be used to enter C-1 state [ 1.903342] Monitor-Mwait will be used to enter C-3 state [ 1.955291] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.024294] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 2.215902] Initializing Nozomi driver 2.1d (build date: Feb 21 2011 19:43:45) [ 2.216702] Non-volatile memory driver v1.3 [ 2.217228] Linux agpgart interface v0.103 [ 2.217511] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 2.217936] Hangcheck: Using getrawmonotonic(). [ 2.218228] [drm] Initialized drm 1.1.0 20060810 [ 2.218463] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 2.794004] Refined TSC clocksource calibration: 3200.113 MHz. [ 2.794285] Switching to clocksource tsc [ 5.226396] floppy0: no floppy controllers found [ 5.229881] brd: module loaded [ 5.231547] loop: module loaded [ 5.232205] Loading iSCSI transport class v2.0-870. [ 5.233034] Loading Adaptec I2O RAID: Version 2.4 Build 5go [ 5.233304] Detecting Adaptec I2O RAID controllers... [ 5.233704] Adaptec aacraid driver 1.1-5[26400]-ms [ 5.234366] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 5.234877] QLogic Fibre Channel HBA Driver: 8.03.05-k0 [ 5.235300] iscsi: registered transport (qla4xxx) [ 5.235604] QLogic iSCSI HBA Driver [ 5.235865] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) [ 5.236309] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) [ 5.236694] megasas: 00.00.05.29-rc1 Tue. Dec. 7 17:00:00 PDT 2010 [ 5.237059] mpt2sas version 07.100.00.00 loaded [ 5.237651] ahci 0000:00:1f.2: version 3.0 [ 5.237896] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1) [ 5.238276] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 5.238638] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 5.238972] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 5.239370] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 5.239761] ahci 0000:00:1f.2: setting latency timer to 64 [ 5.279603] scsi0 : ahci [ 5.279984] scsi1 : ahci [ 5.280305] scsi2 : ahci [ 5.280624] scsi3 : ahci [ 5.280939] scsi4 : ahci [ 5.281255] scsi5 : ahci [ 5.281928] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 43 [ 5.282332] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 43 [ 5.282730] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 5.283097] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 5.283467] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 5.283835] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 5.284232] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.284564] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 5.285051] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 5.285371] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 5.285691] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 5.285981] ahci: SSS flag set, parallel bus scan disabled [ 5.286290] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 5.286681] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 5.286967] ahci 0000:06:00.0: setting latency timer to 64 [ 5.288194] scsi6 : ahci [ 5.288527] scsi7 : ahci [ 5.288862] scsi8 : ahci [ 5.289172] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 5.289543] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 5.289909] ata9: DUMMY [ 5.290748] SSFDC read-only Flash Translation layer [ 5.291046] L440GX flash mapping: failed to find PIIX4 ISA bridge, cannot continue [ 5.291609] physmap-flash.0: failed to claim resource 0 [ 5.291917] SBC-GXx flash: IO:0x258-0x259 MEM:0xdc000-0xdffff [ 5.292238] NetSc520 flash device: 0x100000 at 0x200000 [ 5.292496] Failed to ioremap_nocache [ 5.292695] Failed to ioremap_nocache [ 5.294064] SNAPGEAR: failed to ioremap() BOOTCS [ 5.294442] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 5.304748] No recognised DiskOnChip devices found [ 5.304989] slram: not enough parameters. [ 5.305201] Ramix PMC551 PCI Mezzanine Ram Driver. (C) 1999,2000 Nortel Networks. [ 5.305581] pmc551: not detected [ 5.305785] Spectra MTD driver built on Feb 21 2011 @ 19:45:04 [ 5.316063] No valid DiskOnChip devices found [ 5.316305] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.316746] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.317186] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.317627] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.318073] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.318515] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.318957] NAND device: Manufacturer ID: 0x98, Chip ID: 0x39 (Toshiba NAND 128MiB 1,8V 8-bit) [ 5.319944] flash size: 128 MiB [ 5.320124] page size: 512 bytes [ 5.320307] OOB area size: 16 bytes [ 5.320499] sector size: 16 KiB [ 5.320678] pages number: 262144 [ 5.320861] pages per sector: 32 [ 5.321044] bus width: 8 [ 5.321200] bits in sector size: 14 [ 5.321393] bits in page size: 9 [ 5.321575] bits in OOB size: 4 [ 5.321754] flash size with OOB: 135168 KiB [ 5.321976] page address bytes: 4 [ 5.322162] sector address bytes: 3 [ 5.322355] options: 0x62 [ 5.323128] Scanning device for bad blocks [ 5.353362] Creating 1 MTD partitions on "NAND 128MiB 1,8V 8-bit": [ 5.353657] 0x000000000000-0x000008000000 : "NAND simulator partition 0" [ 5.354443] ftl_cs: FTL header not found. [ 5.355034] usbcore: registered new interface driver alauda [ 5.377793] onenand_wait: timeout! ctrl=0x0000 intr=0x0000 [ 5.378067] OneNAND Manufacturer: Samsung (0xec) [ 5.378302] OneNAND 16MB 1.8V 16-bit (0x04) [ 5.378520] OneNAND version = 0x001e [ 5.378716] Lock scheme is Continuous Lock [ 5.378935] Scanning device for bad blocks [ 5.379566] Creating 1 MTD partitions on "OneNAND simulator": [ 5.379849] 0x000000000000-0x000001000000 : "OneNAND simulator partition" [ 5.380610] ftl_cs: FTL header not found. [ 5.382988] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 5.383312] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 5.383666] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-k2 [ 5.383951] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 5.384268] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1) [ 5.384642] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 5.384970] e1000e 0000:00:19.0: setting latency timer to 64 [ 5.385358] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.601155] ata6: SATA link down (SStatus 0 SControl 300) [ 5.601453] ata3: SATA link down (SStatus 0 SControl 300) [ 5.601738] ata4: SATA link down (SStatus 0 SControl 300) [ 5.602022] ata5: SATA link down (SStatus 0 SControl 300) [ 5.609131] ata7: SATA link down (SStatus 0 SControl 300) [ 5.699290] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:79:88:54 [ 5.699681] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 5.700031] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 5.700409] Intel(R) Gigabit Ethernet Network Driver - version 2.1.0-k2 [ 5.700717] Copyright (c) 2007-2009 Intel Corporation. [ 5.701045] Intel(R) Virtual Function Network Driver - version 1.0.8-k0 [ 5.701352] Copyright (c) 2009 - 2010 Intel Corporation. [ 5.701676] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 5.702003] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 5.702598] jme: JMicron JMC2XX ethernet driver version 1.0.7 [ 5.703121] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 5.703628] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.2.12 (Jan 03, 2011) [ 5.704113] sky2: driver version 1.28 [ 5.705244] tun: Universal TUN/TAP device driver, 1.6 [ 5.705495] tun: (C) 1999-2004 Max Krasnyansky [ 5.706046] usbcore: registered new interface driver catc [ 5.706311] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 5.706639] usbcore: registered new interface driver kaweth [ 5.706909] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 5.707326] usbcore: registered new interface driver pegasus [ 5.707599] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 5.707962] usbcore: registered new interface driver rtl8150 [ 5.708280] usbcore: registered new interface driver asix [ 5.708593] usbcore: registered new interface driver cdc_ether [ 5.708925] usbcore: registered new interface driver cdc_eem [ 5.709244] usbcore: registered new interface driver dm9601 [ 5.709565] usbcore: registered new interface driver smsc75xx [ 5.709894] usbcore: registered new interface driver smsc95xx [ 5.710218] usbcore: registered new interface driver gl620a [ 5.710540] usbcore: registered new interface driver net1080 [ 5.710861] usbcore: registered new interface driver plusb [ 5.711176] usbcore: registered new interface driver rndis_host [ 5.711509] usbcore: registered new interface driver cdc_subset [ 5.711840] usbcore: registered new interface driver zaurus [ 5.712158] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 5.712577] usbcore: registered new interface driver int51x1 [ 5.712853] cdc_ncm: 7-Feb-2011 [ 5.713080] usbcore: registered new interface driver cdc_ncm [ 5.713354] netconsole: local port 6665 [ 5.713560] netconsole: local IP 10.0.0.0 [ 5.713771] netconsole: interface 'eth0' [ 5.713979] netconsole: remote port 6666 [ 5.714188] netconsole: remote IP 192.168.1.11 [ 5.714415] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 5.714704] netconsole: device eth0 not up yet, forcing it [ 5.792901] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.848434] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 6.003912] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 6.004226] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 6.019859] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 6.020161] ata2.00: applying bridge limits [ 6.021824] ata2.00: configured for UDMA/33 [ 6.049340] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 6.049614] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 6.107463] ata1.00: configured for UDMA/133 [ 6.107887] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 6.108641] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 6.109112] sd 0:0:0:0: [sda] Write Protect is off [ 6.109354] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.109431] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 6.110048] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.175384] sda: sda1 sda2 sda4 < sda5 sda6 sda7 > [ 6.176329] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.426602] ata8: SATA link down (SStatus 0 SControl 300) [ 8.564845] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 8.852419] console [netcon0] enabled [ 8.852620] netconsole: network logging started [ 8.852918] Fusion MPT base driver 3.04.18 [ 8.853137] Copyright (c) 1999-2008 LSI Corporation [ 8.853394] Fusion MPT SPI Host driver 3.04.18 [ 8.853705] Fusion MPT FC Host driver 3.04.18 [ 8.854010] Fusion MPT SAS Host driver 3.04.18 [ 8.854320] Fusion MPT misc device (ioctl) driver 3.04.18 [ 8.854676] mptctl: Registered with Fusion MPT base driver [ 8.854946] mptctl: /dev/mptctl @ (major,minor=10,220) [ 8.855311] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.855619] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96 [ 8.855947] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1) [ 8.856324] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 8.856664] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 8.856946] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 8.857268] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file 'devices' [ 8.857667] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 8.858052] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 8.886955] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 8.887387] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 8.887883] ehci_hcd 0000:00:1a.7: debug port 1 [ 8.888118] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 8.892402] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 8.892717] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 8.893016] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 8.893293] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 8.897601] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 8.906894] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 8.907248] usb usb1: default language 0x0409 [ 8.907486] usb usb1: udev 1, busnum 1, minor = 0 [ 8.907725] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 8.908040] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.908403] usb usb1: Product: EHCI Host Controller [ 8.908647] usb usb1: Manufacturer: Linux 2.6.38-rc5-dt6+ ehci_hcd [ 8.908941] usb usb1: SerialNumber: 0000:00:1a.7 [ 8.909306] usb usb1: usb_probe_device [ 8.909512] usb usb1: configuration #1 chosen from 1 choice [ 8.909810] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 8.910180] hub 1-0:1.0: usb_probe_interface [ 8.910405] hub 1-0:1.0: usb_probe_interface - got id [ 8.910657] hub 1-0:1.0: USB hub found [ 8.910872] hub 1-0:1.0: 6 ports detected [ 8.911086] hub 1-0:1.0: standalone hub [ 8.911293] hub 1-0:1.0: no power switching (usb 1.0) [ 8.911544] hub 1-0:1.0: individual port over-current protection [ 8.911831] hub 1-0:1.0: power on to power good time: 20ms [ 8.912118] hub 1-0:1.0: local power source is good [ 8.912364] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 8.912739] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 8.913221] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1) [ 8.913597] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 8.913940] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 8.914222] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 8.914484] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '002' [ 8.914866] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 8.934805] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 8.935237] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 8.935721] ehci_hcd 0000:00:1d.7: debug port 1 [ 8.935955] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 8.940258] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 8.940574] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 8.940875] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 8.941150] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 8.945457] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 8.954744] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 8.955066] usb usb2: default language 0x0409 [ 8.955303] usb usb2: udev 1, busnum 2, minor = 128 [ 8.955548] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 8.955864] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.956228] usb usb2: Product: EHCI Host Controller [ 8.956473] usb usb2: Manufacturer: Linux 2.6.38-rc5-dt6+ ehci_hcd [ 8.956766] usb usb2: SerialNumber: 0000:00:1d.7 [ 8.957121] usb usb2: usb_probe_device [ 8.957327] usb usb2: configuration #1 chosen from 1 choice [ 8.957604] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 8.957970] hub 2-0:1.0: usb_probe_interface [ 8.958195] hub 2-0:1.0: usb_probe_interface - got id [ 8.958447] hub 2-0:1.0: USB hub found [ 8.958656] hub 2-0:1.0: 6 ports detected [ 8.958875] hub 2-0:1.0: standalone hub [ 8.959082] hub 2-0:1.0: no power switching (usb 1.0) [ 8.959333] hub 2-0:1.0: individual port over-current protection [ 8.959620] hub 2-0:1.0: power on to power good time: 20ms [ 8.959893] hub 2-0:1.0: local power source is good [ 8.960139] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 8.960511] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 8.961021] uhci_hcd: USB Universal Host Controller Interface driver [ 8.961371] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 8.961709] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 8.961991] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 8.962254] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '003' [ 8.962633] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 8.982656] uhci_hcd 0000:00:1a.0: detected 2 ports [ 8.982909] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 8.983221] uhci_hcd 0000:00:1a.0: Performing full reset [ 8.983494] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 8.983779] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 8.984112] usb usb3: default language 0x0409 [ 8.984350] usb usb3: udev 1, busnum 3, minor = 256 [ 8.984595] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 8.984910] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.985271] usb usb3: Product: UHCI Host Controller [ 8.985516] usb usb3: Manufacturer: Linux 2.6.38-rc5-dt6+ uhci_hcd [ 8.985808] usb usb3: SerialNumber: 0000:00:1a.0 [ 8.986164] usb usb3: usb_probe_device [ 8.986369] usb usb3: configuration #1 chosen from 1 choice [ 8.986652] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 8.987007] hub 3-0:1.0: usb_probe_interface [ 8.987231] hub 3-0:1.0: usb_probe_interface - got id [ 8.987483] hub 3-0:1.0: USB hub found [ 8.987693] hub 3-0:1.0: 2 ports detected [ 8.987905] hub 3-0:1.0: standalone hub [ 8.988112] hub 3-0:1.0: no power switching (usb 1.0) [ 8.988362] hub 3-0:1.0: individual port over-current protection [ 8.988649] hub 3-0:1.0: power on to power good time: 2ms [ 8.988919] hub 3-0:1.0: local power source is good [ 8.989164] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 8.989514] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 8.989944] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 8.990271] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1) [ 8.990652] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 8.990988] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 8.991269] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 8.991532] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '004' [ 8.991911] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 9.010590] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 9.011014] hub 1-0:1.0: port 1: status 0501 change 0001 [ 9.011284] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 9.011707] hub 1-0:1.0: port 2: status 0501 change 0001 [ 9.011976] ehci_hcd 0000:00:1a.7: GetStatus port:3 status 001803 0 ACK POWER sig=j CSC CONNECT [ 9.012398] hub 1-0:1.0: port 3: status 0501 change 0001 [ 9.018544] uhci_hcd 0000:00:1a.1: detected 2 ports [ 9.018796] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.019107] uhci_hcd 0000:00:1a.1: Performing full reset [ 9.019381] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 9.019680] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 9.020004] usb usb4: default language 0x0409 [ 9.020241] usb usb4: udev 1, busnum 4, minor = 384 [ 9.020487] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.020802] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.021729] usb usb4: Product: UHCI Host Controller [ 9.021974] usb usb4: Manufacturer: Linux 2.6.38-rc5-dt6+ uhci_hcd [ 9.022265] usb usb4: SerialNumber: 0000:00:1a.1 [ 9.022649] usb usb4: usb_probe_device [ 9.022854] usb usb4: configuration #1 chosen from 1 choice [ 9.023132] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 9.023489] hub 4-0:1.0: usb_probe_interface [ 9.023713] hub 4-0:1.0: usb_probe_interface - got id [ 9.023964] hub 4-0:1.0: USB hub found [ 9.024173] hub 4-0:1.0: 2 ports detected [ 9.024386] hub 4-0:1.0: standalone hub [ 9.024593] hub 4-0:1.0: no power switching (usb 1.0) [ 9.024844] hub 4-0:1.0: individual port over-current protection [ 9.025130] hub 4-0:1.0: power on to power good time: 2ms [ 9.025401] hub 4-0:1.0: local power source is good [ 9.025646] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 9.025995] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.026424] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 9.026752] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 9.027088] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 9.027370] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 9.027632] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '005' [ 9.028011] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 9.058454] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 9.062417] uhci_hcd 0000:00:1a.2: detected 2 ports [ 9.062665] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.062977] uhci_hcd 0000:00:1a.2: Performing full reset [ 9.063249] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 9.063548] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 9.063868] usb usb5: default language 0x0409 [ 9.064106] usb usb5: udev 1, busnum 5, minor = 512 [ 9.064351] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.064666] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.065028] usb usb5: Product: UHCI Host Controller [ 9.065272] usb usb5: Manufacturer: Linux 2.6.38-rc5-dt6+ uhci_hcd [ 9.065565] usb usb5: SerialNumber: 0000:00:1a.2 [ 9.065922] usb usb5: usb_probe_device [ 9.066128] usb usb5: configuration #1 chosen from 1 choice [ 9.066411] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 9.066767] hub 5-0:1.0: usb_probe_interface [ 9.066991] hub 5-0:1.0: usb_probe_interface - got id [ 9.067243] hub 5-0:1.0: USB hub found [ 9.067452] hub 5-0:1.0: 2 ports detected [ 9.067665] hub 5-0:1.0: standalone hub [ 9.067871] hub 5-0:1.0: no power switching (usb 1.0) [ 9.068122] hub 5-0:1.0: individual port over-current protection [ 9.068408] hub 5-0:1.0: power on to power good time: 2ms [ 9.068679] hub 5-0:1.0: local power source is good [ 9.068923] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 9.069273] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.069704] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 9.070028] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 9.070371] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 9.070653] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 9.070915] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '006' [ 9.071296] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 9.086333] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 9.086616] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 9.094310] uhci_hcd 0000:00:1d.0: detected 2 ports [ 9.094562] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.094874] uhci_hcd 0000:00:1d.0: Performing full reset [ 9.095147] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 9.095431] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 9.095752] usb usb6: default language 0x0409 [ 9.095989] usb usb6: udev 1, busnum 6, minor = 640 [ 9.096234] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.096549] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.096912] usb usb6: Product: UHCI Host Controller [ 9.097157] usb usb6: Manufacturer: Linux 2.6.38-rc5-dt6+ uhci_hcd [ 9.097449] usb usb6: SerialNumber: 0000:00:1d.0 [ 9.097808] usb usb6: usb_probe_device [ 9.098013] usb usb6: configuration #1 chosen from 1 choice [ 9.098296] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 9.098654] hub 6-0:1.0: usb_probe_interface [ 9.098878] hub 6-0:1.0: usb_probe_interface - got id [ 9.099129] hub 6-0:1.0: USB hub found [ 9.099338] hub 6-0:1.0: 2 ports detected [ 9.099551] hub 6-0:1.0: standalone hub [ 9.099757] hub 6-0:1.0: no power switching (usb 1.0) [ 9.100008] hub 6-0:1.0: individual port over-current protection [ 9.100294] hub 6-0:1.0: power on to power good time: 2ms [ 9.100565] hub 6-0:1.0: local power source is good [ 9.100809] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 9.101158] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.101599] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 9.101911] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 9.102246] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 9.102535] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 9.102797] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '007' [ 9.103176] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 9.110269] hub 1-0:1.0: state 7 ports 6 chg 000e evt 0000 [ 9.110545] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 9.122220] uhci_hcd 0000:00:1a.1: port 1 portsc 0082,00 [ 9.142161] uhci_hcd 0000:00:1d.1: detected 2 ports [ 9.142413] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.142725] uhci_hcd 0000:00:1d.1: Performing full reset [ 9.142997] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 9.143282] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 9.143603] usb usb7: default language 0x0409 [ 9.143841] usb usb7: udev 1, busnum 7, minor = 768 [ 9.144085] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.144400] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.144762] usb usb7: Product: UHCI Host Controller [ 9.145007] usb usb7: Manufacturer: Linux 2.6.38-rc5-dt6+ uhci_hcd [ 9.145299] usb usb7: SerialNumber: 0000:00:1d.1 [ 9.145659] usb usb7: usb_probe_device [ 9.145865] usb usb7: configuration #1 chosen from 1 choice [ 9.146148] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 9.146501] hub 7-0:1.0: usb_probe_interface [ 9.146725] hub 7-0:1.0: usb_probe_interface - got id [ 9.146976] hub 7-0:1.0: USB hub found [ 9.147185] hub 7-0:1.0: 2 ports detected [ 9.147398] hub 7-0:1.0: standalone hub [ 9.147605] hub 7-0:1.0: no power switching (usb 1.0) [ 9.147856] hub 7-0:1.0: individual port over-current protection [ 9.148143] hub 7-0:1.0: power on to power good time: 2ms [ 9.148413] hub 7-0:1.0: local power source is good [ 9.148658] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 9.149008] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.149452] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 9.149764] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 9.150100] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 9.150388] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 9.150653] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '008' [ 9.151032] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 9.166294] ehci_hcd 0000:00:1a.7: port 1 high speed [ 9.166545] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.174067] uhci_hcd 0000:00:1d.2: detected 2 ports [ 9.174315] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.174627] uhci_hcd 0000:00:1d.2: Performing full reset [ 9.174899] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 9.175184] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 9.175502] usb usb8: default language 0x0409 [ 9.175739] usb usb8: udev 1, busnum 8, minor = 896 [ 9.175984] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.176299] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.176660] usb usb8: Product: UHCI Host Controller [ 9.176904] usb usb8: Manufacturer: Linux 2.6.38-rc5-dt6+ uhci_hcd [ 9.177197] usb usb8: SerialNumber: 0000:00:1d.2 [ 9.177553] usb usb8: usb_probe_device [ 9.177759] usb usb8: configuration #1 chosen from 1 choice [ 9.178043] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 9.178399] hub 8-0:1.0: usb_probe_interface [ 9.178622] hub 8-0:1.0: usb_probe_interface - got id [ 9.178873] hub 8-0:1.0: USB hub found [ 9.179083] hub 8-0:1.0: 2 ports detected [ 9.179296] hub 8-0:1.0: standalone hub [ 9.179503] hub 8-0:1.0: no power switching (usb 1.0) [ 9.179754] hub 8-0:1.0: individual port over-current protection [ 9.180040] hub 8-0:1.0: power on to power good time: 2ms [ 9.180311] hub 8-0:1.0: local power source is good [ 9.180556] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 9.180908] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.181350] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 9.181714] Initializing USB Mass Storage driver... [ 9.182064] usbcore: registered new interface driver usb-storage [ 9.182353] USB Mass Storage support registered. [ 9.182693] usbcore: registered new interface driver libusual [ 9.183029] usbcore: registered new interface driver ums-alauda [ 9.183366] usbcore: registered new interface driver ums-cypress [ 9.183705] usbcore: registered new interface driver ums-datafab [ 9.184045] usbcore: registered new interface driver ums-freecom [ 9.184951] usbcore: registered new interface driver ums-isd200 [ 9.185289] usbcore: registered new interface driver ums-jumpshot [ 9.185630] usbcore: registered new interface driver ums-karma [ 9.185961] usbcore: registered new interface driver ums-onetouch [ 9.186322] usbcore: registered new interface driver ums-sddr09 [ 9.186665] usbcore: registered new interface driver ums-sddr55 [ 9.187016] usbcore: registered new interface driver ums-usbat [ 9.187428] usbcore: registered new interface driver usbserial [ 9.187770] USB Serial support registered for generic [ 9.221927] usb 1-1: new high speed USB device using ehci_hcd and address 2 [ 9.277949] ehci_hcd 0000:00:1a.7: port 1 high speed [ 9.278201] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.360216] usb 1-1: default language 0x0409 [ 9.366823] usb 1-1: udev 2, busnum 1, minor = 1 [ 9.367065] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 9.367379] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.367709] usb 1-1: Product: AX88178 [ 9.367913] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 9.368161] usb 1-1: SerialNumber: 000013 [ 9.368500] usb 1-1: usb_probe_device [ 9.368707] usb 1-1: configuration #1 chosen from 1 choice [ 9.369567] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 9.370376] asix 1-1:1.0: usb_probe_interface [ 9.370608] asix 1-1:1.0: usb_probe_interface - got id [ 10.102994] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 10.103508] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '002' [ 10.103921] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 10.104225] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 10.159025] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 10.159476] hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s [ 10.215044] ehci_hcd 0000:00:1a.7: port 3 high speed [ 10.215293] ehci_hcd 0000:00:1a.7: GetStatus port:3 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 10.258828] usb usb5: suspend_rh (auto-stop) [ 10.259075] usb usb6: suspend_rh (auto-stop) [ 10.259315] usb usb7: suspend_rh (auto-stop) [ 10.259555] usb usb8: suspend_rh (auto-stop) [ 10.259805] usb usb4: suspend_rh (auto-stop) [ 10.270674] usb 1-3: new high speed USB device using ehci_hcd and address 4 [ 10.326698] ehci_hcd 0000:00:1a.7: port 3 high speed [ 10.326948] ehci_hcd 0000:00:1a.7: GetStatus port:3 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 11.341084] usb 1-3: default language 0x0409 [ 11.342698] usb 1-3: udev 4, busnum 1, minor = 3 [ 11.342939] usb 1-3: New USB device found, idVendor=1307, idProduct=0165 [ 11.343254] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.343588] usb 1-3: Product: USB Mass Storage Device [ 11.343843] usb 1-3: Manufacturer: Teclast Technology [ 11.344097] usb 1-3: SerialNumber: 0000000000020D [ 11.344462] usb 1-3: usb_probe_device [ 11.344669] usb 1-3: configuration #1 chosen from 1 choice [ 11.345073] usb 1-3: adding 1-3:1.0 (config #1, interface 0) [ 11.345439] usb-storage 1-3:1.0: usb_probe_interface [ 11.345696] usb-storage 1-3:1.0: usb_probe_interface - got id [ 11.346048] scsi9 : usb-storage 1-3:1.0 [ 11.346495] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '004' [ 11.346902] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 11.346983] usbcore: registered new interface driver usbserial_generic [ 11.346985] usbserial: USB Serial Driver core [ 11.347050] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 11.347131] usbcore: registered new interface driver belkin [ 11.347132] belkin_sa: v1.3:USB Belkin Serial converter driver [ 11.347197] USB Serial support registered for MCT U232 [ 11.347273] usbcore: registered new interface driver mct_u232 [ 11.347275] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver [ 11.347553] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 11.349950] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 11.350236] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 11.350517] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 11.351026] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 11.351289] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 11.351869] mousedev: PS/2 mouse device common for all mice [ 11.352774] rtc_cmos 00:02: RTC can wake from S4 [ 11.387352] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 11.387675] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 11.388048] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 11.388507] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 11.388952] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 11.389247] iTCO_vendor_support: vendor-support=0 [ 11.389489] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 11.389796] md: linear personality registered for level -1 [ 11.390067] md: raid0 personality registered for level 0 [ 11.390331] md: raid1 personality registered for level 1 [ 11.390594] md: raid10 personality registered for level 10 [ 11.390864] md: raid6 personality registered for level 6 [ 11.391129] md: raid5 personality registered for level 5 [ 11.391398] md: raid4 personality registered for level 4 [ 11.391663] md: multipath personality registered for level -4 [ 11.391943] md: faulty personality registered for level -5 [ 11.392283] device-mapper: uevent: version 1.0.3 [ 11.392652] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com [ 11.393197] device-mapper: multipath: version 1.2.0 loaded [ 11.393479] device-mapper: multipath round-robin: version 1.0.0 loaded [ 11.393788] device-mapper: multipath queue-length: version 0.1.0 loaded [ 11.394100] device-mapper: multipath service-time: version 0.2.0 loaded [ 11.394506] device-mapper: dm-log-userspace: version 1.1.0 loaded [ 11.396070] cpuidle: using governor ladder [ 11.398842] cpuidle: using governor menu [ 11.399116] sdhci: Secure Digital Host Controller Interface driver [ 11.399422] sdhci: Copyright(c) Pierre Ossman [ 11.399811] usbcore: registered new interface driver ushc [ 11.400659] usbcore: registered new interface driver usbhid [ 11.400936] usbhid: USB HID core driver [ 11.401488] dell-wmi: No known WMI GUID found [ 11.401720] acer-wmi: Acer Laptop ACPI-WMI Extras [ 11.401966] acer-wmi: No or unsupported WMI interface, unable to load [ 11.402637] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1) [ 11.403020] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 11.403451] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 11.403746] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 11.404034] ALSA hda_intel.c:2535: chipset global capabilities = 0x4401 [ 11.435055] ALSA hda_intel.c:913: codec_mask = 0x4 [ 11.435444] ALSA hda_intel.c:1353: codec #2 probed OK [ 11.443211] ALSA hda_codec.c:3726: hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 11.443705] hda_codec: ALC889: SKU not ready 0x411111f0 [ 11.444087] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 11.447084] ALSA hda_codec.c:2164: Cannot find slave Side Playback Volume, skipped [ 11.447504] ALSA hda_codec.c:2164: Cannot find slave Headphone Playback Volume, skipped [ 11.447938] ALSA hda_codec.c:2164: Cannot find slave Mono Playback Volume, skipped [ 11.448354] ALSA hda_codec.c:2164: Cannot find slave Line-Out Playback Volume, skipped [ 11.448783] ALSA hda_codec.c:2164: Cannot find slave PCM Playback Volume, skipped [ 11.449202] ALSA hda_codec.c:2164: Cannot find slave Side Playback Switch, skipped [ 11.449620] ALSA hda_codec.c:2164: Cannot find slave Mono Playback Switch, skipped [ 11.450037] ALSA hda_codec.c:2164: Cannot find slave Line-Out Playback Switch, skipped [ 11.450467] ALSA hda_codec.c:2164: Cannot find slave PCM Playback Switch, skipped [ 11.451568] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 11.452374] ALSA device list: [ 11.452557] #0: HDA Intel at 0xf7f00000 irq 45 [ 11.452891] oprofile: using NMI interrupt. [ 11.453175] netem: version 1.2 [ 11.453360] Netfilter messages via NETLINK v0.30. [ 11.453635] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 11.454776] ctnetlink v0.93: registering with nfnetlink. [ 11.455134] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 11.455463] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 11.456171] xt_time: kernel timezone is -0000 [ 11.457738] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.458086] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 11.458427] arp_tables: (C) 2002 David S. Miller [ 11.458701] TCP bic registered [ 11.458885] TCP cubic registered [ 11.459160] TCP westwood registered [ 11.459358] TCP highspeed registered [ 11.459559] TCP hybla registered [ 11.459746] TCP htcp registered [ 11.459930] TCP vegas registered [ 11.460118] TCP veno registered [ 11.460302] TCP scalable registered [ 11.460499] TCP lp registered [ 11.460676] TCP yeah registered [ 11.460861] TCP illinois registered [ 11.461058] Initializing XFRM netlink socket [ 11.461300] NET: Registered protocol family 17 [ 11.461544] NET: Registered protocol family 15 [ 11.462130] Bridge firewalling registered [ 11.462359] Ebtables v2.0 registered [ 11.467339] PM: Hibernation image not present or could not be loaded. [ 11.467670] registered taskstats version 1 [ 11.469020] Magic number: 15:409:176 [ 11.469292] tty ttyr2: hash matches [ 11.469559] acpi device:0c: hash matches [ 11.469978] rtc_cmos 00:02: setting system clock to 2011-02-22 11:11:14 UTC (1298373074) [ 11.478964] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 11.590587] usb 3-2: new low speed USB device using uhci_hcd and address 2 [ 11.799481] usb 3-2: skipped 1 descriptor after interface [ 11.799777] usb 3-2: skipped 1 descriptor after interface [ 11.806456] usb 3-2: default language 0x0409 [ 11.834368] usb 3-2: udev 2, busnum 3, minor = 257 [ 11.834639] usb 3-2: New USB device found, idVendor=0557, idProduct=2220 [ 11.834977] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 11.835330] usb 3-2: Product: ATEN CS-1758/54 [ 11.835579] usb 3-2: Manufacturer: ATEN [ 11.836147] usb 3-2: usb_probe_device [ 11.836385] usb 3-2: configuration #1 chosen from 1 choice [ 11.839356] usb 3-2: adding 3-2:1.0 (config #1, interface 0) [ 11.880444] usbserial_generic 3-2:1.0: usb_probe_interface [ 11.880742] usbserial_generic 3-2:1.0: usb_probe_interface - got id [ 11.881113] usbhid 3-2:1.0: usb_probe_interface [ 11.881367] usbhid 3-2:1.0: usb_probe_interface - got id [ 11.937974] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input4 [ 11.938506] uhci_hcd 0000:00:1a.0: reserve dev 2 ep81-INT, period 8, phase 4, 118 us [ 11.939234] generic-usb 0003:0557:2220.0001: input: USB HID v1.10 Keyboard [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input0 [ 11.939853] usb 3-2: adding 3-2:1.1 (config #1, interface 1) [ 11.948297] usbserial_generic 3-2:1.1: usb_probe_interface [ 11.948596] usbserial_generic 3-2:1.1: usb_probe_interface - got id [ 11.948944] usbhid 3-2:1.1: usb_probe_interface [ 11.949198] usbhid 3-2:1.1: usb_probe_interface - got id [ 11.977664] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.1/input/input5 [ 11.978649] generic-usb 0003:0557:2220.0002: input: USB HID v1.10 Mouse [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input1 [ 11.979263] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '002' [ 11.979725] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 11.980026] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 11.980317] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 11.980608] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 11.980898] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 12.341748] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 12.345330] scsi_scan_9 used greatest stack depth: 4776 bytes left [ 12.346239] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 12.347230] sd 9:0:0:0: [sdb] Write Protect is off [ 12.347489] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 12.348285] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.348570] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.352961] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.353248] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.534843] sdb: sdb1 sdb2 sdb3 [ 12.539011] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.539279] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.539568] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 12.970402] IP-Config: Complete: [ 12.970594] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 12.971053] host=fat, domain=, nis-domain=(none), [ 12.971345] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 12.972013] md: Waiting for all devices to be available before autodetect [ 12.972334] md: If you don't use raid, use raid=noautodetect [ 12.973179] md: Autodetecting RAID arrays. [ 12.973404] md: Scanned 0 and added 0 devices. [ 12.973637] md: autorun ... [ 12.973808] md: ... autorun DONE. [ 12.983382] VFS: Mounted root (nfs filesystem) on device 0:16. [ 12.983687] debug: unmapping init memory ffffffff82088000..ffffffff82366000 [ 13.100532] stty used greatest stack depth: 2848 bytes left [ 13.451979] create_static_n used greatest stack depth: 2784 bytes left [ 13.692016] net.agent used greatest stack depth: 2688 bytes left [ 13.771647] hwclock-set used greatest stack depth: 2672 bytes left [ 13.776114] blkid used greatest stack depth: 2576 bytes left [ 13.933040] hdparm used greatest stack depth: 2560 bytes left [ 14.977358] sshd (2458): /proc/2458/oom_adj is deprecated, please use /proc/2458/oom_score_adj instead. [ 18.454475] XFS mounting filesystem sda7 [ 18.521913] Ending clean XFS mount for filesystem: sda7 [ 26.884844] XFS mounting filesystem sdb3 [ 27.558168] Ending clean XFS mount for filesystem: sdb3