[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 2.6.38-rc6-dt6+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #762 SMP Tue Feb 22 15:03:18 CST 2011 [ 0.000000] Command line: run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh mem=512M log_buf_len=8M debug sched_debug apic=debug dynamic_printk panic=10 hung_task_panic=1 softlockup_panic=1 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.11/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcde3000 (usable) [ 0.000000] BIOS-e820: 00000000bcde3000 - 00000000bcffb000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcffb000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] e820 remove range: 0000000020000000 - ffffffffffffffff (usable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] user-defined physical RAM map: [ 0.000000] user: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] user: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] user: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] user: 0000000000100000 - 0000000020000000 (usable) [ 0.000000] user: 00000000bcde3000 - 00000000bcffb000 (ACPI NVS) [ 0.000000] user: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] user: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] user: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] user: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] user: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] user: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0x20000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] init_memory_mapping: 0000000000000000-0000000020000000 [ 0.000000] 0000000000 - 0020000000 page 4k [ 0.000000] kernel direct mapping tables up to 20000000 @ 1fefe000-20000000 [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110112/tbfadt-557) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110112/tbfadt-607) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fc000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000020000000 [ 0.000000] Initmem setup node 0 0000000000000000-0000000020000000 [ 0.000000] NODE_DATA [000000001fef9000 - 000000001fefdfff] [ 0.000000] [ffffea0000000000-ffffea00007fffff] PMD -> [ffff88001ee00000-ffff88001f5fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x00020000 [ 0.000000] On node 0 totalpages: 130956 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 6 pages reserved [ 0.000000] DMA zone: 3918 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 1736 pages used for memmap [ 0.000000] DMA32 zone: 125240 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fc000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fb000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:9cde3000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff88001ce00000 s1916224 r8192 d21184 u2097152 [ 0.000000] pcpu-alloc: s1916224 r8192 d21184 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 129158 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh mem=512M log_buf_len=8M debug sched_debug apic=debug dynamic_printk panic=10 hung_task_panic=1 softlockup_panic=1 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.11/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] log_buf_len: 8388608 [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000000] Memory: 445480k/524288k available (11127k kernel code, 464k absent, 78344k reserved, 5792k data, 2936k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:4352 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6335 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 5242880 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] ODEBUG: 23 of 23 active objects replaced [ 0.004000] Fast TSC calibration using PIT [ 0.008000] Detected 3200.160 MHz processor. [ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 6400.32 BogoMIPS (lpj=12800640) [ 0.000536] pid_max: default: 32768 minimum: 301 [ 0.000962] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.001408] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.001786] Mount-cache hash table entries: 256 [ 0.002327] Initializing cgroup subsys debug [ 0.002550] Initializing cgroup subsys ns [ 0.002762] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup. [ 0.003184] Initializing cgroup subsys cpuacct [ 0.003418] Initializing cgroup subsys memory [ 0.003667] Initializing cgroup subsys devices [ 0.003896] Initializing cgroup subsys freezer [ 0.004124] Initializing cgroup subsys blkio [ 0.004417] CPU: Physical Processor ID: 0 [ 0.004629] CPU: Processor Core ID: 0 [ 0.004831] mce: CPU supports 9 MCE banks [ 0.005048] CPU0: Thermal monitoring enabled (TM1) [ 0.005298] using mwait in idle threads. [ 0.006369] ACPI: Core revision 20110112 [ 0.020538] ftrace: allocating 34978 entries in 138 pages [ 0.029159] Getting VERSION: 60015 [ 0.029349] Getting VERSION: 60015 [ 0.029537] Getting ID: 0 [ 0.029698] Getting ID: 0 [ 0.029859] Setting APIC routing to physical flat [ 0.030097] enabled ExtINT on CPU#0 [ 0.030445] ESR value before enabling vector: 0x00000040 after: 0x00000000 [ 0.030766] ENABLING IO-APIC IRQs [ 0.030952] init IO_APIC IRQs [ 0.031125] 8-0 (apicid-pin) not connected [ 0.031382] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0) [ 0.031750] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0) [ 0.032119] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0) [ 0.032491] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0) [ 0.032860] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0) [ 0.033228] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0) [ 0.033598] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0) [ 0.033967] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0) [ 0.034336] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0) [ 0.035273] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0) [ 0.035646] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0) [ 0.036020] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0) [ 0.036398] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0) [ 0.036773] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0) [ 0.037148] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0) [ 0.037522] 8-16 8-17 8-18 8-19 8-20 8-21 8-22 8-23 (apicid-pin) not connected [ 0.038285] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.078131] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.078524] Using local APIC timer interrupts. [ 0.078524] calibrating APIC timer ... [ 0.183801] ... lapic delta = 833413 [ 0.183997] ... PM-Timer delta = 357976 [ 0.184201] ... PM-Timer result ok [ 0.184390] ..... delta 833413 [ 0.184566] ..... mult: 35792578 [ 0.184749] ..... calibration result: 533384 [ 0.184970] ..... CPU clock speed is 3200.1219 MHz. [ 0.185214] ..... host bus clock speed is 133.1384 MHz. [ 0.185481] Performance Events: PEBS fmt1+, Nehalem events, Intel PMU driver. [ 0.185909] ... version: 3 [ 0.186121] ... bit width: 48 [ 0.186335] ... generic registers: 4 [ 0.186547] ... value mask: 0000ffffffffffff [ 0.186807] ... max period: 000000007fffffff [ 0.187066] ... fixed-purpose events: 3 [ 0.187278] ... event mask: 000000070000000f [ 0.187958] lockdep: fixing up alternatives. [ 0.188245] Booting Node 0, Processors #1masked ExtINT on CPU#1 [ 0.297459] lockdep: fixing up alternatives. [ 0.297737] #2masked ExtINT on CPU#2 [ 0.405113] lockdep: fixing up alternatives. [ 0.405363] #3masked ExtINT on CPU#3 [ 0.512746] lockdep: fixing up alternatives. [ 0.512996] #4masked ExtINT on CPU#4 [ 0.624462] lockdep: fixing up alternatives. [ 0.624713] #5masked ExtINT on CPU#5 [ 0.732098] lockdep: fixing up alternatives. [ 0.732350] #6masked ExtINT on CPU#6 [ 0.839730] lockdep: fixing up alternatives. [ 0.839981] #7masked ExtINT on CPU#7 [ 0.947276] Brought up 8 CPUs [ 0.947452] Total of 8 processors activated (51202.79 BogoMIPS). [ 0.950676] CPU0 attaching sched-domain: [ 0.950890] domain 0: span 0,4 level SIBLING [ 0.951157] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 0.951599] domain 1: span 0-7 level MC [ 0.951844] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.952623] CPU1 attaching sched-domain: [ 0.952832] domain 0: span 1,5 level SIBLING [ 0.953089] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 0.953530] domain 1: span 0-7 level MC [ 0.953774] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.954553] CPU2 attaching sched-domain: [ 0.954762] domain 0: span 2,6 level SIBLING [ 0.955019] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 0.955464] domain 1: span 0-7 level MC [ 0.955708] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.956485] CPU3 attaching sched-domain: [ 0.956693] domain 0: span 3,7 level SIBLING [ 0.956950] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 0.957392] domain 1: span 0-7 level MC [ 0.957636] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.958412] CPU4 attaching sched-domain: [ 0.958621] domain 0: span 0,4 level SIBLING [ 0.958878] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 0.959323] domain 1: span 0-7 level MC [ 0.959568] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.960343] CPU5 attaching sched-domain: [ 0.960552] domain 0: span 1,5 level SIBLING [ 0.960809] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 0.961251] domain 1: span 0-7 level MC [ 0.961496] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.962273] CPU6 attaching sched-domain: [ 0.962482] domain 0: span 2,6 level SIBLING [ 0.962740] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 0.963185] domain 1: span 0-7 level MC [ 0.963430] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.964207] CPU7 attaching sched-domain: [ 0.964416] domain 0: span 3,7 level SIBLING [ 0.964673] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 0.965115] domain 1: span 0-7 level MC [ 0.965360] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.966609] kworker/u:0 used greatest stack depth: 5320 bytes left [ 0.968548] xor: automatically using best checksumming function: generic_sse [ 0.987018] generic_sse: 11972.000 MB/sec [ 0.987240] xor: using function: generic_sse (11972.000 MB/sec) [ 0.987601] Time: 15:33:09 Date: 02/22/11 [ 0.987920] NET: Registered protocol family 16 [ 0.988850] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.989229] ACPI: bus type pci registered [ 0.989606] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.990046] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 1.001094] PCI: Using configuration type 1 for base access [ 1.024593] bio: create slab at 0 [ 1.090704] raid6: int64x1 2629 MB/s [ 1.158483] raid6: int64x2 3087 MB/s [ 1.226292] raid6: int64x4 2594 MB/s [ 1.294068] raid6: int64x8 2594 MB/s [ 1.361859] raid6: sse2x1 7887 MB/s [ 1.429646] raid6: sse2x2 9293 MB/s [ 1.497439] raid6: sse2x4 10296 MB/s [ 1.497642] raid6: using algorithm sse2x4 (10296 MB/s) [ 1.502073] ACPI: EC: Look up EC in DSDT [ 1.530269] ACPI: Interpreter enabled [ 1.530470] ACPI: (supports S0 S1 S3 S4 S5) [ 1.530902] ACPI: Using IOAPIC for interrupt routing [ 1.561636] ACPI: No dock devices found. [ 1.561847] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.563127] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 1.565163] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 1.565478] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 1.565786] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.566151] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 1.566514] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 1.566879] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 1.567268] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 1.567619] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 1.567957] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.568247] pci 0000:00:01.0: PME# disabled [ 1.568489] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 1.568827] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 1.569117] pci 0000:00:03.0: PME# disabled [ 1.569366] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 1.569704] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 1.569994] pci 0000:00:07.0: PME# disabled [ 1.570242] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 1.570599] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 1.570956] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 1.571312] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 1.571668] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 1.572019] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 1.572380] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 1.572681] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 1.572978] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 1.573278] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 1.573599] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.573890] pci 0000:00:19.0: PME# disabled [ 1.574126] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 1.574460] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 1.574778] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 1.575112] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 1.575428] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 1.575762] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 1.576089] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 1.576393] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 1.576766] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 1.577056] pci 0000:00:1a.7: PME# disabled [ 1.577303] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 1.577603] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 1.577979] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.578271] pci 0000:00:1b.0: PME# disabled [ 1.578511] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 1.578861] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.579153] pci 0000:00:1c.0: PME# disabled [ 1.579393] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 1.579742] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.580033] pci 0000:00:1c.1: PME# disabled [ 1.580278] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 1.580628] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.580918] pci 0000:00:1c.4: PME# disabled [ 1.581163] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 1.581504] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 1.581822] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 1.582720] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 1.583035] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 1.583368] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 1.583695] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 1.583998] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 1.584370] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 1.584662] pci 0000:00:1d.7: PME# disabled [ 1.584898] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 1.585255] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 1.585634] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 1.585924] pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO [ 1.586313] pci 0000:00:1f.0: quirk: [io 0x0500-0x053f] claimed by ICH6 GPIO [ 1.586642] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 1.587016] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 1.587436] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 1.587738] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 1.588008] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 1.588279] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 1.588549] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 1.588820] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 1.589090] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 1.589420] pci 0000:00:1f.2: PME# supported from D3hot [ 1.589678] pci 0000:00:1f.2: PME# disabled [ 1.589915] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 1.590215] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 1.590548] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 1.590884] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.591143] pci 0000:00:01.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.591469] pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.591853] pci 0000:00:01.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.592302] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 1.592595] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 1.592892] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 1.593236] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 1.593564] pci 0000:02:00.0: supports D1 D2 [ 1.593809] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 1.594101] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 1.594456] pci 0000:02:00.1: supports D1 D2 [ 1.594695] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.594953] pci 0000:00:03.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.595279] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.595596] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.596021] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.596278] pci 0000:00:07.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.596603] pci 0000:00:07.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.596987] pci 0000:00:07.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.597438] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.597698] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.598024] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.598409] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.598855] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.599114] pci 0000:00:1c.1: bridge window [io 0xf000-0x0000] (disabled) [ 1.599441] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff] (disabled) [ 1.599825] pci 0000:00:1c.1: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.600293] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 1.600597] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 1.600875] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 1.601159] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 1.601438] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 1.601716] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 1.601994] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 1.602347] pci 0000:06:00.0: supports D1 [ 1.602560] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 1.602840] pci 0000:06:00.0: PME# disabled [ 1.603077] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.603336] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.603627] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.603945] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.604387] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 1.604688] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 1.604987] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 1.605353] pci 0000:07:03.0: supports D1 D2 [ 1.605575] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 1.605871] pci 0000:07:03.0: PME# disabled [ 1.606141] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 1.606468] pci 0000:00:1e.0: bridge window [io 0xf000-0x0000] (disabled) [ 1.606794] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.607113] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) [ 1.607510] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.607897] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.608283] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.608694] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 1.609109] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 1.609523] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 1.609970] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.611677] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 1.612340] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 1.612759] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 1.613183] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 1.613605] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 1.614024] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 1.614457] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 1.644558] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.645496] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.646422] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.647349] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.648280] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.649219] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.650148] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.651072] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.652166] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.652566] vgaarb: loaded [ 1.653175] SCSI subsystem initialized [ 1.653531] libata version 3.00 loaded. [ 1.653981] usbcore: registered new interface driver usbfs [ 1.654305] usbcore: registered new interface driver hub [ 1.654632] usbcore: registered new device driver usb [ 1.655442] wmi: Mapper loaded [ 1.655681] Advanced Linux Sound Architecture Driver Version 1.0.23. [ 1.655979] PCI: Using ACPI for IRQ routing [ 1.656198] PCI: pci_cache_line_size set to 64 bytes [ 1.656629] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 1.657211] [ 1.657212] printing PIC contents [ 1.657589] ... PIC IMR: ffff [ 1.657768] ... PIC IRR: 0c21 [ 1.657950] ... PIC ISR: 0000 [ 1.658129] ... PIC ELCR: 0c20 [ 1.658305] printing local APIC contents on CPU#0/0: [ 1.658552] ... APIC ID: 00000000 (0) [ 1.658766] ... APIC VERSION: 00060015 [ 1.658968] ... APIC TASKPRI: 00000000 (00) [ 1.659186] ... APIC PROCPRI: 00000000 [ 1.659388] ... APIC LDR: 01000000 [ 1.659576] ... APIC DFR: ffffffff [ 1.659765] ... APIC SPIV: 000001ff [ 1.659957] ... APIC ISR field: [ 1.660136] 0000000000000000000000000000000000000000000000000000000000000000 [ 1.660725] ... APIC TMR field: [ 1.660905] 0000000000000000000000000000000000000000000000000000000000000000 [ 1.661493] ... APIC IRR field: [ 1.661674] 0000000000000000000000000000000000000000000000000000000000008000 [ 1.662261] ... APIC ESR: 00000000 [ 1.662450] ... APIC ICR: 000000fc [ 1.662640] ... APIC ICR2: 07000000 [ 1.662832] ... APIC LVTT: 000200ef [ 1.663025] ... APIC LVTPC: 00000400 [ 1.663220] ... APIC LVT0: 00010700 [ 1.663412] ... APIC LVT1: 00000400 [ 1.663604] ... APIC LVTERR: 000000fe [ 1.663803] ... APIC TMICT: 00008238 [ 1.663998] ... APIC TMCCT: 00001e80 [ 1.664194] ... APIC TDCR: 00000003 [ 1.664386] [ 1.664510] number of MP IRQ sources: 15. [ 1.664721] number of IO-APIC #8 registers: 24. [ 1.664955] testing the IO APIC....................... [ 1.665213] [ 1.665332] IO APIC #8...... [ 1.665502] .... register #00: 08000000 [ 1.665707] ....... : physical APIC id: 08 [ 1.666499] ....... : Delivery Type: 0 [ 1.666711] ....... : LTS : 0 [ 1.666921] .... register #01: 00170020 [ 1.667126] ....... : max redirection entries: 0017 [ 1.667382] ....... : PRQ implemented: 0 [ 1.667603] ....... : IO APIC version: 0020 [ 1.667833] .... IRQ redirection table: [ 1.668038] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 1.668306] 00 000 1 0 0 0 0 0 0 00 [ 1.668599] 01 000 0 0 0 0 0 0 0 31 [ 1.668893] 02 000 0 0 0 0 0 0 0 30 [ 1.669188] 03 000 0 0 0 0 0 0 0 33 [ 1.669480] 04 000 0 0 0 0 0 0 0 34 [ 1.669773] 05 000 0 0 0 0 0 0 0 35 [ 1.670066] 06 000 0 0 0 0 0 0 0 36 [ 1.670358] 07 000 0 0 0 0 0 0 0 37 [ 1.670651] 08 000 0 0 0 0 0 0 0 38 [ 1.670943] 09 000 0 1 0 0 0 0 0 39 [ 1.671235] 0a 000 0 0 0 0 0 0 0 3A [ 1.671528] 0b 000 0 0 0 0 0 0 0 3B [ 1.671821] 0c 000 0 0 0 0 0 0 0 3C [ 1.672113] 0d 000 0 0 0 0 0 0 0 3D [ 1.672405] 0e 000 0 0 0 0 0 0 0 3E [ 1.672697] 0f 000 0 0 0 0 0 0 0 3F [ 1.672992] 10 000 1 0 0 0 0 0 0 00 [ 1.673285] 11 000 1 0 0 0 0 0 0 00 [ 1.673578] 12 000 1 0 0 0 0 0 0 00 [ 1.673870] 13 000 1 0 0 0 0 0 0 00 [ 1.674163] 14 000 1 0 0 0 0 0 0 00 [ 1.674454] 15 000 1 0 0 0 0 0 0 00 [ 1.674747] 16 000 1 0 0 0 0 0 0 00 [ 1.675040] 17 000 1 0 0 0 0 0 0 00 [ 1.675330] IRQ to pin mappings: [ 1.675512] IRQ0 -> 0:2 [ 1.675733] IRQ1 -> 0:1 [ 1.675954] IRQ3 -> 0:3 [ 1.676174] IRQ4 -> 0:4 [ 1.676394] IRQ5 -> 0:5 [ 1.676615] IRQ6 -> 0:6 [ 1.676835] IRQ7 -> 0:7 [ 1.677058] IRQ8 -> 0:8 [ 1.677278] IRQ9 -> 0:9 [ 1.677498] IRQ10 -> 0:10 [ 1.677725] IRQ11 -> 0:11 [ 1.677952] IRQ12 -> 0:12 [ 1.678177] IRQ13 -> 0:13 [ 1.678404] IRQ14 -> 0:14 [ 1.678629] IRQ15 -> 0:15 [ 1.678856] .................................... done. [ 1.679185] hpet clockevent registered [ 1.679389] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 1.679715] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 1.680136] hpet0: 4 comparators, 64-bit 14.318180 MHz counter [ 1.701036] Switching to clocksource hpet [ 1.704848] Switched to NOHz mode on CPU #0 [ 1.704893] Switched to NOHz mode on CPU #6 [ 1.704896] Switched to NOHz mode on CPU #3 [ 1.704927] Switched to NOHz mode on CPU #5 [ 1.704940] Switched to NOHz mode on CPU #2 [ 1.704946] Switched to NOHz mode on CPU #1 [ 1.704964] Switched to NOHz mode on CPU #4 [ 1.704976] Switched to NOHz mode on CPU #7 [ 1.730248] pnp: PnP ACPI init [ 1.730451] ACPI: bus type pnp registered [ 1.731535] pnp 00:00: [bus 00-3d] [ 1.731726] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.731942] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.732180] pnp 00:00: [io 0x0d00-0xffff window] [ 1.732417] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.732680] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 1.732944] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 1.733217] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 1.733481] pnp 00:00: [mem 0x00000000 window] [ 1.733857] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 1.734515] pnp 00:01: [io 0x0000-0x000f] [ 1.734731] pnp 00:01: [io 0x0081-0x0083] [ 1.734949] pnp 00:01: [io 0x0087] [ 1.735142] pnp 00:01: [io 0x0089-0x008b] [ 1.735357] pnp 00:01: [io 0x008f] [ 1.735550] pnp 00:01: [io 0x00c0-0x00df] [ 1.735765] pnp 00:01: [dma 4] [ 1.736043] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.736366] pnp 00:02: [io 0x0070-0x0071] [ 1.736581] pnp 00:02: [io 0x0074-0x0077] [ 1.736799] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0) [ 1.737179] pnp 00:02: [irq 8] [ 1.737460] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.737789] pnp 00:03: [io 0x00f0] [ 1.737984] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0) [ 1.738358] pnp 00:03: [irq 13] [ 1.738642] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.738969] pnp 00:04: [io 0x0061] [ 1.739267] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.739594] pnp 00:05: [io 0x0500-0x053f] [ 1.739809] pnp 00:05: [io 0x0400-0x047f] [ 1.740025] pnp 00:05: [io 0x0092] [ 1.740217] pnp 00:05: [io 0x0680-0x06ff] [ 1.740432] pnp 00:05: [io 0x0010-0x001f] [ 1.740647] pnp 00:05: [io 0x0072-0x0073] [ 1.740862] pnp 00:05: [io 0x0080] [ 1.741055] pnp 00:05: [io 0x0084-0x0086] [ 1.741278] pnp 00:05: [io 0x0088] [ 1.741470] pnp 00:05: [io 0x008c-0x008e] [ 1.741686] pnp 00:05: [io 0x0090-0x009f] [ 1.742070] system 00:05: [io 0x0500-0x053f] has been reserved [ 1.742354] system 00:05: [io 0x0400-0x047f] has been reserved [ 1.742637] system 00:05: [io 0x0680-0x06ff] has been reserved [ 1.742921] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.743335] pnp 00:06: [io 0x0060] [ 1.743528] pnp 00:06: [io 0x0064] [ 1.743881] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.744863] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 1.745231] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 1.745694] pnp: PnP ACPI: found 8 devices [ 1.745911] ACPI: ACPI bus type pnp unregistered [ 1.756839] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 1.757325] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.757582] pci 0000:00:01.0: bridge window [io disabled] [ 1.757856] pci 0000:00:01.0: bridge window [mem disabled] [ 1.758131] pci 0000:00:01.0: bridge window [mem pref disabled] [ 1.758426] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 1.758789] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.759045] pci 0000:00:03.0: bridge window [io disabled] [ 1.759320] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.759636] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.760020] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.760276] pci 0000:00:07.0: bridge window [io disabled] [ 1.760551] pci 0000:00:07.0: bridge window [mem disabled] [ 1.760825] pci 0000:00:07.0: bridge window [mem pref disabled] [ 1.761123] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.761379] pci 0000:00:1c.0: bridge window [io disabled] [ 1.761655] pci 0000:00:1c.0: bridge window [mem disabled] [ 1.761929] pci 0000:00:1c.0: bridge window [mem pref disabled] [ 1.762222] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.762478] pci 0000:00:1c.1: bridge window [io disabled] [ 1.762754] pci 0000:00:1c.1: bridge window [mem disabled] [ 1.763028] pci 0000:00:1c.1: bridge window [mem pref disabled] [ 1.763321] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.763579] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.763870] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.764187] pci 0000:00:1c.4: bridge window [mem pref disabled] [ 1.764479] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 1.764736] pci 0000:00:1e.0: bridge window [io disabled] [ 1.765018] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.765334] pci 0000:00:1e.0: bridge window [mem pref disabled] [ 1.765638] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1) [ 1.766012] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.766326] pci 0000:00:01.0: setting latency timer to 64 [ 1.766593] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.766905] pci 0000:00:03.0: setting latency timer to 64 [ 1.767173] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.767487] pci 0000:00:07.0: setting latency timer to 64 [ 1.767761] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1) [ 1.768134] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.768448] pci 0000:00:1c.0: setting latency timer to 64 [ 1.768716] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 1.769036] pci 0000:00:1c.1: setting latency timer to 64 [ 1.769305] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.769618] pci 0000:00:1c.4: setting latency timer to 64 [ 1.769887] pci 0000:00:1e.0: setting latency timer to 64 [ 1.770153] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.770423] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.770692] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.770988] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.771282] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.771578] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.771873] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 1.772168] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.772530] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 1.772801] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 1.773102] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 1.773397] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 1.774235] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 1.774505] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 1.774800] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.775095] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.775389] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.775806] NET: Registered protocol family 2 [ 1.776214] IP route cache hash table entries: 4096 (order: 3, 32768 bytes) [ 1.777115] TCP established hash table entries: 16384 (order: 6, 262144 bytes) [ 1.777819] TCP bind hash table entries: 16384 (order: 8, 1310720 bytes) [ 1.778711] TCP: Hash tables configured (established 16384 bind 16384) [ 1.779021] TCP reno registered [ 1.779215] UDP hash table entries: 256 (order: 3, 49152 bytes) [ 1.779525] UDP-Lite hash table entries: 256 (order: 3, 49152 bytes) [ 1.780039] NET: Registered protocol family 1 [ 1.780493] RPC: Registered udp transport module. [ 1.780731] RPC: Registered tcp transport module. [ 1.780978] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.781318] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.781622] pci 0000:00:1a.0: Performing full reset [ 1.781883] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.782187] pci 0000:00:1a.1: Performing full reset [ 1.782446] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.782750] pci 0000:00:1a.2: Performing full reset [ 1.783154] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.783458] pci 0000:00:1d.0: Performing full reset [ 1.783718] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.784021] pci 0000:00:1d.1: Performing full reset [ 1.784281] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.784585] pci 0000:00:1d.2: Performing full reset [ 1.784984] pci 0000:02:00.0: Boot video device [ 1.785227] PCI: CLS 64 bytes, default 64 [ 1.789145] Machine check injector initialized [ 1.790932] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 1.791217] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 1.791500] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 1.791783] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 1.792068] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 1.792354] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 1.792637] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 1.792927] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 1.793281] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 1.793701] Scanning for low memory corruption every 60 seconds [ 1.794420] audit: initializing netlink socket (disabled) [ 1.794712] type=2000 audit(1298388789.580:1): initialized [ 1.807164] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.808933] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.809562] fuse init (API version 7.16) [ 1.809946] JFS: nTxBlock = 3480, nTxLock = 27842 [ 1.811504] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.812739] Btrfs loaded [ 1.812916] msgmni has been set to 870 [ 1.813909] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.814283] io scheduler noop registered [ 1.814492] io scheduler deadline registered [ 1.814761] io scheduler cfq registered (default) [ 1.815380] pcieport 0000:00:1c.0: setting latency timer to 64 [ 1.815711] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 1.816090] pcieport 0000:00:1c.1: setting latency timer to 64 [ 1.816417] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 1.816799] pcieport 0000:00:1c.4: setting latency timer to 64 [ 1.817134] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 1.817685] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.818445] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 1.892635] ACPI: Sleep Button [SLPB] [ 1.892972] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.893344] ACPI: Power Button [PWRF] [ 1.894308] ACPI: acpi_idle registered with cpuidle [ 1.895035] Monitor-Mwait will be used to enter C-1 state [ 1.895333] Monitor-Mwait will be used to enter C-3 state [ 1.947913] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.012310] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 2.207906] Initializing Nozomi driver 2.1d (build date: Feb 22 2011 15:00:47) [ 2.208706] Non-volatile memory driver v1.3 [ 2.209233] Linux agpgart interface v0.103 [ 2.209515] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 2.209940] Hangcheck: Using getrawmonotonic(). [ 2.210232] [drm] Initialized drm 1.1.0 20060810 [ 2.210467] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 2.782036] Refined TSC clocksource calibration: 3200.113 MHz. [ 2.782317] Switching to clocksource tsc [ 5.222364] floppy0: no floppy controllers found [ 5.225867] brd: module loaded [ 5.227522] loop: module loaded [ 5.228174] Loading iSCSI transport class v2.0-870. [ 5.228994] Loading Adaptec I2O RAID: Version 2.4 Build 5go [ 5.229264] Detecting Adaptec I2O RAID controllers... [ 5.229663] Adaptec aacraid driver 1.1-5[26400]-ms [ 5.230296] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 5.230813] QLogic Fibre Channel HBA Driver: 8.03.05-k0 [ 5.231239] iscsi: registered transport (qla4xxx) [ 5.231542] QLogic iSCSI HBA Driver [ 5.231805] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) [ 5.232246] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) [ 5.232631] megasas: 00.00.05.29-rc1 Tue. Dec. 7 17:00:00 PDT 2010 [ 5.232995] mpt2sas version 07.100.00.00 loaded [ 5.233582] ahci 0000:00:1f.2: version 3.0 [ 5.233828] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1) [ 5.234207] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 5.234570] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 5.234904] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 5.235303] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 5.235693] ahci 0000:00:1f.2: setting latency timer to 64 [ 5.275539] scsi0 : ahci [ 5.275922] scsi1 : ahci [ 5.276242] scsi2 : ahci [ 5.276561] scsi3 : ahci [ 5.276882] scsi4 : ahci [ 5.277197] scsi5 : ahci [ 5.277870] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 43 [ 5.278274] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 43 [ 5.278671] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 5.279039] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 5.279407] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 5.279775] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 5.280172] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.280502] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 5.280990] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 5.281310] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 5.281630] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 5.281921] ahci: SSS flag set, parallel bus scan disabled [ 5.282227] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 5.282617] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 5.282904] ahci 0000:06:00.0: setting latency timer to 64 [ 5.284120] scsi6 : ahci [ 5.284453] scsi7 : ahci [ 5.284783] scsi8 : ahci [ 5.285105] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 5.285475] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 5.285842] ata9: DUMMY [ 5.286675] SSFDC read-only Flash Translation layer [ 5.286972] L440GX flash mapping: failed to find PIIX4 ISA bridge, cannot continue [ 5.287536] physmap-flash.0: failed to claim resource 0 [ 5.287843] SBC-GXx flash: IO:0x258-0x259 MEM:0xdc000-0xdffff [ 5.288163] NetSc520 flash device: 0x100000 at 0x200000 [ 5.288421] Failed to ioremap_nocache [ 5.288622] Failed to ioremap_nocache [ 5.325606] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 5.335915] No recognised DiskOnChip devices found [ 5.336156] slram: not enough parameters. [ 5.336368] Ramix PMC551 PCI Mezzanine Ram Driver. (C) 1999,2000 Nortel Networks. [ 5.336747] pmc551: not detected [ 5.336951] Spectra MTD driver built on Feb 22 2011 @ 15:01:58 [ 5.347223] No valid DiskOnChip devices found [ 5.347465] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.347907] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.348348] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.348790] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.349231] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.349672] [nandsim] warning: read_byte: unexpected data output cycle, state is STATE_READY return 0x0 [ 5.350687] NAND device: Manufacturer ID: 0x98, Chip ID: 0x39 (Toshiba NAND 128MiB 1,8V 8-bit) [ 5.351104] flash size: 128 MiB [ 5.351284] page size: 512 bytes [ 5.351467] OOB area size: 16 bytes [ 5.351659] sector size: 16 KiB [ 5.351839] pages number: 262144 [ 5.352021] pages per sector: 32 [ 5.352204] bus width: 8 [ 5.352361] bits in sector size: 14 [ 5.352554] bits in page size: 9 [ 5.352736] bits in OOB size: 4 [ 5.352916] flash size with OOB: 135168 KiB [ 5.353134] page address bytes: 4 [ 5.353320] sector address bytes: 3 [ 5.353512] options: 0x62 [ 5.354278] Scanning device for bad blocks [ 5.384097] Creating 1 MTD partitions on "NAND 128MiB 1,8V 8-bit": [ 5.384392] 0x000000000000-0x000008000000 : "NAND simulator partition 0" [ 5.385161] ftl_cs: FTL header not found. [ 5.385754] usbcore: registered new interface driver alauda [ 5.409640] onenand_wait: timeout! ctrl=0x0000 intr=0x0000 [ 5.409910] OneNAND Manufacturer: Samsung (0xec) [ 5.410144] OneNAND 16MB 1.8V 16-bit (0x04) [ 5.410362] OneNAND version = 0x001e [ 5.410557] Lock scheme is Continuous Lock [ 5.410781] Scanning device for bad blocks [ 5.411409] Creating 1 MTD partitions on "OneNAND simulator": [ 5.411689] 0x000000000000-0x000001000000 : "OneNAND simulator partition" [ 5.412436] ftl_cs: FTL header not found. [ 5.414787] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 5.415112] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 5.415465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-k2 [ 5.415751] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 5.416068] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1) [ 5.416442] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 5.416769] e1000e 0000:00:19.0: setting latency timer to 64 [ 5.417151] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.597126] ata3: SATA link down (SStatus 0 SControl 300) [ 5.597416] ata4: SATA link down (SStatus 0 SControl 300) [ 5.597701] ata5: SATA link down (SStatus 0 SControl 300) [ 5.597987] ata6: SATA link down (SStatus 0 SControl 300) [ 5.605115] ata7: SATA link down (SStatus 0 SControl 300) [ 5.731194] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:c0:79:88:54 [ 5.731585] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 5.731936] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 5.732323] Intel(R) Gigabit Ethernet Network Driver - version 2.1.0-k2 [ 5.732632] Copyright (c) 2007-2009 Intel Corporation. [ 5.732969] Intel(R) Virtual Function Network Driver - version 1.0.8-k0 [ 5.733278] Copyright (c) 2009 - 2010 Intel Corporation. [ 5.733610] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 5.733938] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 5.734566] jme: JMicron JMC2XX ethernet driver version 1.0.7 [ 5.735119] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 5.735646] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.2.12 (Jan 03, 2011) [ 5.736131] sky2: driver version 1.28 [ 5.737327] tun: Universal TUN/TAP device driver, 1.6 [ 5.737578] tun: (C) 1999-2004 Max Krasnyansky [ 5.738175] usbcore: registered new interface driver catc [ 5.738439] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 5.738777] usbcore: registered new interface driver kaweth [ 5.739048] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 5.739471] usbcore: registered new interface driver pegasus [ 5.739744] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 5.740114] usbcore: registered new interface driver rtl8150 [ 5.740441] usbcore: registered new interface driver asix [ 5.740762] usbcore: registered new interface driver cdc_ether [ 5.741094] usbcore: registered new interface driver cdc_eem [ 5.741419] usbcore: registered new interface driver dm9601 [ 5.741747] usbcore: registered new interface driver smsc75xx [ 5.742080] usbcore: registered new interface driver smsc95xx [ 5.742409] usbcore: registered new interface driver gl620a [ 5.742731] usbcore: registered new interface driver net1080 [ 5.743056] usbcore: registered new interface driver plusb [ 5.743377] usbcore: registered new interface driver rndis_host [ 5.743713] usbcore: registered new interface driver cdc_subset [ 5.744051] usbcore: registered new interface driver zaurus [ 5.744377] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 5.744815] usbcore: registered new interface driver int51x1 [ 5.745088] cdc_ncm: 7-Feb-2011 [ 5.745325] usbcore: registered new interface driver cdc_ncm [ 5.745600] netconsole: local port 6665 [ 5.745805] netconsole: local IP 10.0.0.0 [ 5.746017] netconsole: interface 'eth0' [ 5.746226] netconsole: remote port 6666 [ 5.746434] netconsole: remote IP 192.168.1.11 [ 5.746661] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 5.746951] netconsole: device eth0 not up yet, forcing it [ 5.828763] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.884303] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.999904] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 6.000218] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 6.012794] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 6.013097] ata2.00: applying bridge limits [ 6.014768] ata2.00: configured for UDMA/33 [ 6.048765] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 6.049038] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 6.106886] ata1.00: configured for UDMA/133 [ 6.107311] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 6.108047] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 6.108515] sd 0:0:0:0: [sda] Write Protect is off [ 6.108758] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.108848] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 6.109455] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.174823] sda: sda1 sda2 sda4 < sda5 sda6 sda7 > [ 6.175812] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.426586] ata8: SATA link down (SStatus 0 SControl 300) [ 8.652546] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 8.943870] console [netcon0] enabled [ 8.944072] netconsole: network logging started [ 8.944370] Fusion MPT base driver 3.04.18 [ 8.944587] Copyright (c) 1999-2008 LSI Corporation [ 8.944843] Fusion MPT SPI Host driver 3.04.18 [ 8.945147] Fusion MPT FC Host driver 3.04.18 [ 8.945445] Fusion MPT SAS Host driver 3.04.18 [ 8.945750] Fusion MPT misc device (ioctl) driver 3.04.18 [ 8.946096] mptctl: Registered with Fusion MPT base driver [ 8.946365] mptctl: /dev/mptctl @ (major,minor=10,220) [ 8.946716] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.947028] ehci_hcd: block sizes: qh 104 qtd 96 itd 192 sitd 96 [ 8.947353] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1) [ 8.947728] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 8.948069] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 8.948350] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 8.948671] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file 'devices' [ 8.949073] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 8.949456] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 8.978648] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 8.979081] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 8.979577] ehci_hcd 0000:00:1a.7: debug port 1 [ 8.979812] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 8.984099] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 8.984414] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 8.984716] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 8.984992] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 8.989298] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 8.998587] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 8.998941] usb usb1: default language 0x0409 [ 8.999180] usb usb1: udev 1, busnum 1, minor = 0 [ 8.999418] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 8.999732] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.000095] usb usb1: Product: EHCI Host Controller [ 9.000340] usb usb1: Manufacturer: Linux 2.6.38-rc6-dt6+ ehci_hcd [ 9.000633] usb usb1: SerialNumber: 0000:00:1a.7 [ 9.000986] usb usb1: usb_probe_device [ 9.001192] usb usb1: configuration #1 chosen from 1 choice [ 9.001490] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 9.001853] hub 1-0:1.0: usb_probe_interface [ 9.002076] hub 1-0:1.0: usb_probe_interface - got id [ 9.002328] hub 1-0:1.0: USB hub found [ 9.002538] hub 1-0:1.0: 6 ports detected [ 9.002757] hub 1-0:1.0: standalone hub [ 9.002964] hub 1-0:1.0: no power switching (usb 1.0) [ 9.003215] hub 1-0:1.0: individual port over-current protection [ 9.003502] hub 1-0:1.0: power on to power good time: 20ms [ 9.003788] hub 1-0:1.0: local power source is good [ 9.004033] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 9.004405] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.004887] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1) [ 9.005263] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 9.005606] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 9.005887] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 9.006149] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '002' [ 9.006525] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 9.026499] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 9.026931] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 9.027416] ehci_hcd 0000:00:1d.7: debug port 1 [ 9.027650] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.031955] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 9.032270] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 9.032573] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 9.032848] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.037154] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 9.046434] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 9.046755] usb usb2: default language 0x0409 [ 9.046992] usb usb2: udev 1, busnum 2, minor = 128 [ 9.047238] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 9.047553] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.047916] usb usb2: Product: EHCI Host Controller [ 9.048161] usb usb2: Manufacturer: Linux 2.6.38-rc6-dt6+ ehci_hcd [ 9.048454] usb usb2: SerialNumber: 0000:00:1d.7 [ 9.048803] usb usb2: usb_probe_device [ 9.049008] usb usb2: configuration #1 chosen from 1 choice [ 9.049286] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 9.049633] hub 2-0:1.0: usb_probe_interface [ 9.049856] hub 2-0:1.0: usb_probe_interface - got id [ 9.050107] hub 2-0:1.0: USB hub found [ 9.050316] hub 2-0:1.0: 6 ports detected [ 9.050535] hub 2-0:1.0: standalone hub [ 9.050742] hub 2-0:1.0: no power switching (usb 1.0) [ 9.050993] hub 2-0:1.0: individual port over-current protection [ 9.051280] hub 2-0:1.0: power on to power good time: 20ms [ 9.051554] hub 2-0:1.0: local power source is good [ 9.051799] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 9.052170] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.052675] uhci_hcd: USB Universal Host Controller Interface driver [ 9.053028] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.053367] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 9.053648] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 9.053910] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '003' [ 9.054287] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 9.074351] uhci_hcd 0000:00:1a.0: detected 2 ports [ 9.074604] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.074917] uhci_hcd 0000:00:1a.0: Performing full reset [ 9.075190] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 9.075476] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 9.075807] usb usb3: default language 0x0409 [ 9.076046] usb usb3: udev 1, busnum 3, minor = 256 [ 9.076290] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.076606] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.076968] usb usb3: Product: UHCI Host Controller [ 9.077213] usb usb3: Manufacturer: Linux 2.6.38-rc6-dt6+ uhci_hcd [ 9.077506] usb usb3: SerialNumber: 0000:00:1a.0 [ 9.077856] usb usb3: usb_probe_device [ 9.078063] usb usb3: configuration #1 chosen from 1 choice [ 9.078346] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 9.078707] hub 3-0:1.0: usb_probe_interface [ 9.078930] hub 3-0:1.0: usb_probe_interface - got id [ 9.079181] hub 3-0:1.0: USB hub found [ 9.079391] hub 3-0:1.0: 2 ports detected [ 9.079604] hub 3-0:1.0: standalone hub [ 9.079810] hub 3-0:1.0: no power switching (usb 1.0) [ 9.080062] hub 3-0:1.0: individual port over-current protection [ 9.080348] hub 3-0:1.0: power on to power good time: 2ms [ 9.080619] hub 3-0:1.0: local power source is good [ 9.080864] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 9.081215] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.081649] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 9.081977] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1) [ 9.082357] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 9.082694] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 9.082975] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 9.083238] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '004' [ 9.083614] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 9.102285] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 9.102712] hub 1-0:1.0: port 1: status 0501 change 0001 [ 9.102983] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 9.103406] hub 1-0:1.0: port 2: status 0501 change 0001 [ 9.103676] ehci_hcd 0000:00:1a.7: GetStatus port:3 status 001803 0 ACK POWER sig=j CSC CONNECT [ 9.104099] hub 1-0:1.0: port 3: status 0501 change 0001 [ 9.110236] uhci_hcd 0000:00:1a.1: detected 2 ports [ 9.110489] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.110801] uhci_hcd 0000:00:1a.1: Performing full reset [ 9.111073] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 9.111375] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 9.111693] usb usb4: default language 0x0409 [ 9.111930] usb usb4: udev 1, busnum 4, minor = 384 [ 9.112176] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.112491] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.112854] usb usb4: Product: UHCI Host Controller [ 9.113667] usb usb4: Manufacturer: Linux 2.6.38-rc6-dt6+ uhci_hcd [ 9.113959] usb usb4: SerialNumber: 0000:00:1a.1 [ 9.114319] usb usb4: usb_probe_device [ 9.114524] usb usb4: configuration #1 chosen from 1 choice [ 9.114801] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 9.115145] hub 4-0:1.0: usb_probe_interface [ 9.115368] hub 4-0:1.0: usb_probe_interface - got id [ 9.115619] hub 4-0:1.0: USB hub found [ 9.115828] hub 4-0:1.0: 2 ports detected [ 9.116040] hub 4-0:1.0: standalone hub [ 9.116247] hub 4-0:1.0: no power switching (usb 1.0) [ 9.116498] hub 4-0:1.0: individual port over-current protection [ 9.116784] hub 4-0:1.0: power on to power good time: 2ms [ 9.117055] hub 4-0:1.0: local power source is good [ 9.117300] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 9.117651] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.118084] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 9.118412] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 9.118748] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 9.119030] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 9.119292] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '005' [ 9.119668] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 9.138152] uhci_hcd 0000:00:1a.2: detected 2 ports [ 9.138404] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.138715] uhci_hcd 0000:00:1a.2: Performing full reset [ 9.138988] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 9.139290] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 9.139611] usb usb5: default language 0x0409 [ 9.139848] usb usb5: udev 1, busnum 5, minor = 512 [ 9.140093] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.140408] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.140770] usb usb5: Product: UHCI Host Controller [ 9.141015] usb usb5: Manufacturer: Linux 2.6.38-rc6-dt6+ uhci_hcd [ 9.141307] usb usb5: SerialNumber: 0000:00:1a.2 [ 9.141654] usb usb5: usb_probe_device [ 9.141859] usb usb5: configuration #1 chosen from 1 choice [ 9.142142] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 9.142491] hub 5-0:1.0: usb_probe_interface [ 9.142714] hub 5-0:1.0: usb_probe_interface - got id [ 9.142965] hub 5-0:1.0: USB hub found [ 9.143174] hub 5-0:1.0: 2 ports detected [ 9.143387] hub 5-0:1.0: standalone hub [ 9.143593] hub 5-0:1.0: no power switching (usb 1.0) [ 9.143844] hub 5-0:1.0: individual port over-current protection [ 9.144130] hub 5-0:1.0: power on to power good time: 2ms [ 9.144401] hub 5-0:1.0: local power source is good [ 9.144646] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 9.144995] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.145432] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 9.145758] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 9.146093] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 9.146380] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 9.146643] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '006' [ 9.147020] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 9.150152] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 9.178030] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 9.178313] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 9.186005] uhci_hcd 0000:00:1d.0: detected 2 ports [ 9.186257] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.186568] uhci_hcd 0000:00:1d.0: Performing full reset [ 9.186841] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 9.187125] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 9.187447] usb usb6: default language 0x0409 [ 9.187684] usb usb6: udev 1, busnum 6, minor = 640 [ 9.187929] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.188245] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.188607] usb usb6: Product: UHCI Host Controller [ 9.188852] usb usb6: Manufacturer: Linux 2.6.38-rc6-dt6+ uhci_hcd [ 9.189145] usb usb6: SerialNumber: 0000:00:1d.0 [ 9.189494] usb usb6: usb_probe_device [ 9.189699] usb usb6: configuration #1 chosen from 1 choice [ 9.189982] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 9.190330] hub 6-0:1.0: usb_probe_interface [ 9.190553] hub 6-0:1.0: usb_probe_interface - got id [ 9.190804] hub 6-0:1.0: USB hub found [ 9.191013] hub 6-0:1.0: 2 ports detected [ 9.191226] hub 6-0:1.0: standalone hub [ 9.191432] hub 6-0:1.0: no power switching (usb 1.0) [ 9.191683] hub 6-0:1.0: individual port over-current protection [ 9.191969] hub 6-0:1.0: power on to power good time: 2ms [ 9.192239] hub 6-0:1.0: local power source is good [ 9.192485] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 9.192836] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.193280] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 9.193592] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 9.193928] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 9.194214] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 9.194478] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '007' [ 9.194855] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 9.201963] hub 1-0:1.0: state 7 ports 6 chg 000e evt 0000 [ 9.202239] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 9.213917] uhci_hcd 0000:00:1a.1: port 1 portsc 0082,00 [ 9.233861] uhci_hcd 0000:00:1d.1: detected 2 ports [ 9.234108] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.234420] uhci_hcd 0000:00:1d.1: Performing full reset [ 9.234693] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 9.234976] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 9.235297] usb usb7: default language 0x0409 [ 9.235535] usb usb7: udev 1, busnum 7, minor = 768 [ 9.235780] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.236095] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.236457] usb usb7: Product: UHCI Host Controller [ 9.236702] usb usb7: Manufacturer: Linux 2.6.38-rc6-dt6+ uhci_hcd [ 9.236995] usb usb7: SerialNumber: 0000:00:1d.1 [ 9.237344] usb usb7: usb_probe_device [ 9.237550] usb usb7: configuration #1 chosen from 1 choice [ 9.237832] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 9.238182] hub 7-0:1.0: usb_probe_interface [ 9.238405] hub 7-0:1.0: usb_probe_interface - got id [ 9.238657] hub 7-0:1.0: USB hub found [ 9.238866] hub 7-0:1.0: 2 ports detected [ 9.239079] hub 7-0:1.0: standalone hub [ 9.239286] hub 7-0:1.0: no power switching (usb 1.0) [ 9.239537] hub 7-0:1.0: individual port over-current protection [ 9.239824] hub 7-0:1.0: power on to power good time: 2ms [ 9.240094] hub 7-0:1.0: local power source is good [ 9.240340] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 9.240689] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.241132] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 9.241444] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 9.241779] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 9.242070] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 9.242353] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '008' [ 9.242730] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 9.258115] ehci_hcd 0000:00:1a.7: port 1 high speed [ 9.258369] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.265799] uhci_hcd 0000:00:1d.2: detected 2 ports [ 9.266048] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.266360] uhci_hcd 0000:00:1d.2: Performing full reset [ 9.266633] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 9.266918] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 9.267238] usb usb8: default language 0x0409 [ 9.267476] usb usb8: udev 1, busnum 8, minor = 896 [ 9.267720] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.268035] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.268398] usb usb8: Product: UHCI Host Controller [ 9.268642] usb usb8: Manufacturer: Linux 2.6.38-rc6-dt6+ uhci_hcd [ 9.268935] usb usb8: SerialNumber: 0000:00:1d.2 [ 9.269287] usb usb8: usb_probe_device [ 9.269492] usb usb8: configuration #1 chosen from 1 choice [ 9.269775] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 9.270124] hub 8-0:1.0: usb_probe_interface [ 9.270348] hub 8-0:1.0: usb_probe_interface - got id [ 9.270599] hub 8-0:1.0: USB hub found [ 9.270809] hub 8-0:1.0: 2 ports detected [ 9.271021] hub 8-0:1.0: standalone hub [ 9.271228] hub 8-0:1.0: no power switching (usb 1.0) [ 9.271479] hub 8-0:1.0: individual port over-current protection [ 9.271766] hub 8-0:1.0: power on to power good time: 2ms [ 9.272037] hub 8-0:1.0: local power source is good [ 9.272282] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 9.272630] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '001' [ 9.273076] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 9.273432] Initializing USB Mass Storage driver... [ 9.273760] usbcore: registered new interface driver usb-storage [ 9.274047] USB Mass Storage support registered. [ 9.274369] usbcore: registered new interface driver libusual [ 9.274700] usbcore: registered new interface driver ums-alauda [ 9.275034] usbcore: registered new interface driver ums-cypress [ 9.275377] usbcore: registered new interface driver ums-datafab [ 9.275718] usbcore: registered new interface driver ums-freecom [ 9.276058] usbcore: registered new interface driver ums-isd200 [ 9.276960] usbcore: registered new interface driver ums-jumpshot [ 9.277300] usbcore: registered new interface driver ums-karma [ 9.277631] usbcore: registered new interface driver ums-onetouch [ 9.277990] usbcore: registered new interface driver ums-sddr09 [ 9.278327] usbcore: registered new interface driver ums-sddr55 [ 9.278670] usbcore: registered new interface driver ums-usbat [ 9.279085] usbcore: registered new interface driver usbserial [ 9.279436] USB Serial support registered for generic [ 9.313634] usb 1-1: new high speed USB device using ehci_hcd and address 2 [ 9.369646] ehci_hcd 0000:00:1a.7: port 1 high speed [ 9.369896] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.452036] usb 1-1: default language 0x0409 [ 9.458642] usb 1-1: udev 2, busnum 1, minor = 1 [ 9.458884] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 9.459198] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.459528] usb 1-1: Product: AX88178 [ 9.459733] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 9.459980] usb 1-1: SerialNumber: 000013 [ 9.460318] usb 1-1: usb_probe_device [ 9.460525] usb 1-1: configuration #1 chosen from 1 choice [ 9.461388] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 9.462196] asix 1-1:1.0: usb_probe_interface [ 9.462428] asix 1-1:1.0: usb_probe_interface - got id [ 10.194689] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 10.195203] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '002' [ 10.195617] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 10.195921] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 10.250724] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 10.251175] hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s [ 10.254830] usb usb5: suspend_rh (auto-stop) [ 10.255078] usb usb6: suspend_rh (auto-stop) [ 10.255318] usb usb7: suspend_rh (auto-stop) [ 10.306742] ehci_hcd 0000:00:1a.7: port 3 high speed [ 10.306992] ehci_hcd 0000:00:1a.7: GetStatus port:3 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 10.362365] usb 1-3: new high speed USB device using ehci_hcd and address 4 [ 10.418395] ehci_hcd 0000:00:1a.7: port 3 high speed [ 10.418644] ehci_hcd 0000:00:1a.7: GetStatus port:3 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 10.501971] usb usb8: suspend_rh (auto-stop) [ 10.502225] usb usb4: suspend_rh (auto-stop) [ 11.432780] usb 1-3: default language 0x0409 [ 11.434394] usb 1-3: udev 4, busnum 1, minor = 3 [ 11.434638] usb 1-3: New USB device found, idVendor=1307, idProduct=0165 [ 11.434952] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.435289] usb 1-3: Product: USB Mass Storage Device [ 11.435543] usb 1-3: Manufacturer: Teclast Technology [ 11.435796] usb 1-3: SerialNumber: 0000000000020D [ 11.436174] usb 1-3: usb_probe_device [ 11.436382] usb 1-3: configuration #1 chosen from 1 choice [ 11.436770] usb 1-3: adding 1-3:1.0 (config #1, interface 0) [ 11.437139] usb-storage 1-3:1.0: usb_probe_interface [ 11.437395] usb-storage 1-3:1.0: usb_probe_interface - got id [ 11.437748] scsi9 : usb-storage 1-3:1.0 [ 11.438200] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '004' [ 11.438605] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 11.438686] usbcore: registered new interface driver usbserial_generic [ 11.438687] usbserial: USB Serial Driver core [ 11.438742] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 11.438816] usbcore: registered new interface driver belkin [ 11.438817] belkin_sa: v1.3:USB Belkin Serial converter driver [ 11.438869] USB Serial support registered for MCT U232 [ 11.438941] usbcore: registered new interface driver mct_u232 [ 11.438942] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver [ 11.439189] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 11.441681] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 11.441974] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 11.442270] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 11.442788] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 11.443057] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 11.443600] mousedev: PS/2 mouse device common for all mice [ 11.444444] rtc_cmos 00:02: RTC can wake from S4 [ 11.471054] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 11.471376] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 11.471741] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 11.472184] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 11.472620] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 11.472915] iTCO_vendor_support: vendor-support=0 [ 11.473157] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 11.473463] md: linear personality registered for level -1 [ 11.473735] md: raid0 personality registered for level 0 [ 11.473999] md: raid1 personality registered for level 1 [ 11.474264] md: raid10 personality registered for level 10 [ 11.474534] md: raid6 personality registered for level 6 [ 11.474799] md: raid5 personality registered for level 5 [ 11.475069] md: raid4 personality registered for level 4 [ 11.475333] md: multipath personality registered for level -4 [ 11.475613] md: faulty personality registered for level -5 [ 11.475950] device-mapper: uevent: version 1.0.3 [ 11.476316] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com [ 11.476852] device-mapper: multipath: version 1.2.0 loaded [ 11.477133] device-mapper: multipath round-robin: version 1.0.0 loaded [ 11.477442] device-mapper: multipath queue-length: version 0.1.0 loaded [ 11.477754] device-mapper: multipath service-time: version 0.2.0 loaded [ 11.478159] device-mapper: dm-log-userspace: version 1.1.0 loaded [ 11.479578] cpuidle: using governor ladder [ 11.482069] cpuidle: using governor menu [ 11.482338] sdhci: Secure Digital Host Controller Interface driver [ 11.482635] sdhci: Copyright(c) Pierre Ossman [ 11.483012] usbcore: registered new interface driver ushc [ 11.483812] usbcore: registered new interface driver usbhid [ 11.484088] usbhid: USB HID core driver [ 11.484604] dell-wmi: No known WMI GUID found [ 11.484836] acer-wmi: Acer Laptop ACPI-WMI Extras [ 11.485080] acer-wmi: No or unsupported WMI interface, unable to load [ 11.485733] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1) [ 11.486115] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 11.486533] HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 11.486827] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 11.487129] ALSA hda_intel.c:2535: chipset global capabilities = 0x4401 [ 11.518830] ALSA hda_intel.c:913: codec_mask = 0x4 [ 11.519236] ALSA hda_intel.c:1353: codec #2 probed OK [ 11.526863] ALSA hda_codec.c:3726: hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 11.527356] hda_codec: ALC889: SKU not ready 0x411111f0 [ 11.527796] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 11.530964] ALSA hda_codec.c:2164: Cannot find slave Side Playback Volume, skipped [ 11.531385] ALSA hda_codec.c:2164: Cannot find slave Headphone Playback Volume, skipped [ 11.531818] ALSA hda_codec.c:2164: Cannot find slave Mono Playback Volume, skipped [ 11.532234] ALSA hda_codec.c:2164: Cannot find slave Line-Out Playback Volume, skipped [ 11.532663] ALSA hda_codec.c:2164: Cannot find slave PCM Playback Volume, skipped [ 11.533081] ALSA hda_codec.c:2164: Cannot find slave Side Playback Switch, skipped [ 11.533499] ALSA hda_codec.c:2164: Cannot find slave Mono Playback Switch, skipped [ 11.533915] ALSA hda_codec.c:2164: Cannot find slave Line-Out Playback Switch, skipped [ 11.534344] ALSA hda_codec.c:2164: Cannot find slave PCM Playback Switch, skipped [ 11.535881] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 11.536666] ALSA device list: [ 11.536847] #0: HDA Intel at 0xf7f00000 irq 45 [ 11.537170] oprofile: using NMI interrupt. [ 11.537459] netem: version 1.2 [ 11.537644] Netfilter messages via NETLINK v0.30. [ 11.537919] nf_conntrack version 0.5.0 (3480 buckets, 13920 max) [ 11.538742] ctnetlink v0.93: registering with nfnetlink. [ 11.539049] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 11.539376] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 11.540086] xt_time: kernel timezone is -0000 [ 11.541648] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.541998] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 11.542337] arp_tables: (C) 2002 David S. Miller [ 11.542610] TCP bic registered [ 11.542832] TCP cubic registered [ 11.543021] TCP westwood registered [ 11.543218] TCP highspeed registered [ 11.543419] TCP hybla registered [ 11.543606] TCP htcp registered [ 11.543790] TCP vegas registered [ 11.543978] TCP veno registered [ 11.544163] TCP scalable registered [ 11.544361] TCP lp registered [ 11.544539] TCP yeah registered [ 11.544723] TCP illinois registered [ 11.544921] Initializing XFRM netlink socket [ 11.545166] NET: Registered protocol family 17 [ 11.545410] NET: Registered protocol family 15 [ 11.545910] Bridge firewalling registered [ 11.546140] Ebtables v2.0 registered [ 11.551297] PM: Hibernation image not present or could not be loaded. [ 11.551629] registered taskstats version 1 [ 11.552413] Magic number: 15:248:589 [ 11.553249] tty ptyc7: hash matches [ 11.553702] rtc_cmos 00:02: setting system clock to 2011-02-22 15:33:19 UTC (1298388799) [ 11.566709] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 11.678318] usb 3-2: new low speed USB device using uhci_hcd and address 2 [ 11.887136] usb 3-2: skipped 1 descriptor after interface [ 11.887429] usb 3-2: skipped 1 descriptor after interface [ 11.894107] usb 3-2: default language 0x0409 [ 11.920029] usb 3-2: udev 2, busnum 3, minor = 257 [ 11.920296] usb 3-2: New USB device found, idVendor=0557, idProduct=2220 [ 11.920633] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 11.920986] usb 3-2: Product: ATEN CS-1758/54 [ 11.921234] usb 3-2: Manufacturer: ATEN [ 11.921786] usb 3-2: usb_probe_device [ 11.922020] usb 3-2: configuration #1 chosen from 1 choice [ 11.924997] usb 3-2: adding 3-2:1.0 (config #1, interface 0) [ 11.966113] usbserial_generic 3-2:1.0: usb_probe_interface [ 11.966409] usbserial_generic 3-2:1.0: usb_probe_interface - got id [ 11.966778] usbhid 3-2:1.0: usb_probe_interface [ 11.967033] usbhid 3-2:1.0: usb_probe_interface - got id [ 12.025758] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input4 [ 12.026290] uhci_hcd 0000:00:1a.0: reserve dev 2 ep81-INT, period 8, phase 4, 118 us [ 12.027105] generic-usb 0003:0557:2220.0001: input: USB HID v1.10 Keyboard [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input0 [ 12.027718] usb 3-2: adding 3-2:1.1 (config #1, interface 1) [ 12.036089] usbserial_generic 3-2:1.1: usb_probe_interface [ 12.036388] usbserial_generic 3-2:1.1: usb_probe_interface - got id [ 12.036736] usbhid 3-2:1.1: usb_probe_interface [ 12.036989] usbhid 3-2:1.1: usb_probe_interface - got id [ 12.067417] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.1/input/input5 [ 12.068664] generic-usb 0003:0557:2220.0002: input: USB HID v1.10 Mouse [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input1 [ 12.069343] /home/wfg/cc/linux-next/drivers/usb/core/inode.c: creating file '002' [ 12.069811] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.070104] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.070395] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.070686] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.070976] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 12.071278] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 12.433386] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 12.436283] scsi_scan_9 used greatest stack depth: 4776 bytes left [ 12.437186] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 12.438175] sd 9:0:0:0: [sdb] Write Protect is off [ 12.438431] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 12.439170] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.439453] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.444088] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.444376] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.626042] sdb: sdb1 sdb2 sdb3 [ 12.630326] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.630663] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.631017] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 13.054195] IP-Config: Complete: [ 13.054405] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 13.054905] host=fat, domain=, nis-domain=(none), [ 13.055217] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 13.056055] md: Waiting for all devices to be available before autodetect [ 13.056398] md: If you don't use raid, use raid=noautodetect [ 13.057628] md: Autodetecting RAID arrays. [ 13.057873] md: Scanned 0 and added 0 devices. [ 13.058143] md: autorun ... [ 13.058328] md: ... autorun DONE. [ 13.068246] VFS: Mounted root (nfs filesystem) on device 0:16. [ 13.068586] debug: unmapping init memory ffffffff82088000..ffffffff82366000 [ 13.176312] stty used greatest stack depth: 2848 bytes left [ 13.529588] create_static_n used greatest stack depth: 2784 bytes left [ 13.754861] modprobe used greatest stack depth: 2576 bytes left [ 13.848463] hwclock-set used greatest stack depth: 2560 bytes left [ 15.039137] sshd (2430): /proc/2430/oom_adj is deprecated, please use /proc/2430/oom_score_adj instead.