[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 3.0.0-sound+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #167 SMP Mon Aug 8 09:40:49 CST 2011 [ 0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcde3000 (usable) [ 0.000000] BIOS-e820: 00000000bcde3000 - 00000000bcffb000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcffb000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf800000 [ 0.000000] 0000000000 - 00bf800000 page 4k [ 0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000 [ 0.000000] log_buf_len: 8388608 [ 0.000000] early log buf free: 258327(98%) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-00000000bf800000 [ 0.000000] Initmem setup node 0 0000000000000000-00000000bf800000 [ 0.000000] NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff] [ 0.000000] [ffffea0000000000-ffffea0002ffffff] PMD -> [ffff8800b9c00000-ffff8800bcbfffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x000bcde3 [ 0.000000] 0: 0x000bcffb -> 0x000bf6bd [ 0.000000] 0: 0x000bf6bf -> 0x000bf714 [ 0.000000] 0: 0x000bf7bf -> 0x000bf7e7 [ 0.000000] 0: 0x000bf7ff -> 0x000bf800 [ 0.000000] On node 0 totalpages: 783535 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3911 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 12192 pages used for memmap [ 0.000000] DMA32 zone: 767363 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bcde3000 - 00000000bcffb000 [ 0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915136 r8192 d22272 u2097152 [ 0.000000] pcpu-alloc: s1915136 r8192 d22272 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 771274 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Memory: 2999372k/3137536k available (14612k kernel code, 3396k absent, 134768k reserved, 6468k data, 2896k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] NR_IRQS:8448 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6367 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 25165824 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] ODEBUG: 23 of 23 active objects replaced [ 0.004000] Fast TSC calibration using PIT [ 0.008000] Detected 3200.026 MHz processor. [ 0.000006] Calibrating delay loop (skipped), value calculated using timer frequency.. 6400.05 BogoMIPS (lpj=12800104) [ 0.000544] pid_max: default: 32768 minimum: 301 [ 0.001847] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003859] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.004790] Mount-cache hash table entries: 256 [ 0.006227] Initializing cgroup subsys debug [ 0.006453] Initializing cgroup subsys cpuacct [ 0.006691] Initializing cgroup subsys memory [ 0.006967] Initializing cgroup subsys devices [ 0.007199] Initializing cgroup subsys freezer [ 0.007428] Initializing cgroup subsys blkio [ 0.007773] CPU: Physical Processor ID: 0 [ 0.007987] CPU: Processor Core ID: 0 [ 0.008190] mce: CPU supports 9 MCE banks [ 0.008427] CPU0: Thermal monitoring enabled (TM1) [ 0.008685] using mwait in idle threads. [ 0.009995] ACPI: Core revision 20110623 [ 0.031435] ftrace: allocating 34967 entries in 138 pages [ 0.040780] Getting VERSION: 60015 [ 0.040973] Getting VERSION: 60015 [ 0.041163] Getting ID: 0 [ 0.041324] Getting ID: 0 [ 0.041487] Switched APIC routing to physical flat. [ 0.041733] enabled ExtINT on CPU#0 [ 0.042095] ENABLING IO-APIC IRQs [ 0.042282] init IO_APIC IRQs [ 0.042458] apic 8 pin 0 not connected [ 0.042683] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0) [ 0.043080] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0) [ 0.043476] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) [ 0.043871] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0) [ 0.044275] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0) [ 0.044672] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0) [ 0.045067] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0) [ 0.045462] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 0.045856] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0) [ 0.046251] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0) [ 0.046652] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0) [ 0.047054] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0) [ 0.047456] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 0.047856] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0) [ 0.048263] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0) [ 0.048664] apic 8 pin 16 not connected [ 0.048873] apic 8 pin 17 not connected [ 0.049083] apic 8 pin 18 not connected [ 0.049292] apic 8 pin 19 not connected [ 0.049502] apic 8 pin 20 not connected [ 0.049711] apic 8 pin 21 not connected [ 0.049920] apic 8 pin 22 not connected [ 0.050129] apic 8 pin 23 not connected [ 0.050473] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.090318] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.090715] Using local APIC timer interrupts. [ 0.090716] calibrating APIC timer ... [ 0.195684] ... lapic delta = 833407 [ 0.195881] ... PM-Timer delta = 357974 [ 0.196086] ... PM-Timer result ok [ 0.196277] ..... delta 833407 [ 0.196455] ..... mult: 35792321 [ 0.196638] ..... calibration result: 533380 [ 0.196860] ..... CPU clock speed is 3200.1151 MHz. [ 0.197104] ..... host bus clock speed is 133.1380 MHz. [ 0.197374] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver. [ 0.197974] ... version: 3 [ 0.198186] ... bit width: 48 [ 0.198402] ... generic registers: 4 [ 0.198615] ... value mask: 0000ffffffffffff [ 0.198876] ... max period: 000000007fffffff [ 0.199138] ... fixed-purpose events: 3 [ 0.199351] ... event mask: 000000070000000f [ 0.200252] lockdep: fixing up alternatives. [ 0.200674] Booting Node 0, Processors #1 [ 0.200894] smpboot cpu 1: start_ip = 97000 [ 0.212177] masked ExtINT on CPU#1 [ 0.309365] lockdep: fixing up alternatives. [ 0.309630] #2 [ 0.309723] smpboot cpu 2: start_ip = 97000 [ 0.321016] masked ExtINT on CPU#2 [ 0.420951] lockdep: fixing up alternatives. [ 0.421220] #3 [ 0.421313] smpboot cpu 3: start_ip = 97000 [ 0.432596] masked ExtINT on CPU#3 [ 0.532625] lockdep: fixing up alternatives. [ 0.532895] #4 [ 0.532988] smpboot cpu 4: start_ip = 97000 [ 0.544266] masked ExtINT on CPU#4 [ 0.644351] lockdep: fixing up alternatives. [ 0.644618] #5 [ 0.644711] smpboot cpu 5: start_ip = 97000 [ 0.655986] masked ExtINT on CPU#5 [ 0.755942] lockdep: fixing up alternatives. [ 0.756211] #6 [ 0.756305] smpboot cpu 6: start_ip = 97000 [ 0.768147] masked ExtINT on CPU#6 [ 0.867608] lockdep: fixing up alternatives. [ 0.867875] #7 [ 0.867967] smpboot cpu 7: start_ip = 97000 [ 0.879249] masked ExtINT on CPU#7 [ 0.979089] Brought up 8 CPUs [ 0.979269] Total of 8 processors activated (51202.46 BogoMIPS). [ 0.984495] CPU0 attaching sched-domain: [ 0.984711] domain 0: span 0,4 level SIBLING [ 0.984971] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 0.985418] domain 1: span 0-7 level MC [ 0.985664] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.986464] CPU1 attaching sched-domain: [ 0.986673] domain 0: span 1,5 level SIBLING [ 0.986932] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 0.987388] domain 1: span 0-7 level MC [ 0.987634] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.988421] CPU2 attaching sched-domain: [ 0.988630] domain 0: span 2,6 level SIBLING [ 0.988889] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 0.989335] domain 1: span 0-7 level MC [ 0.989580] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.990366] CPU3 attaching sched-domain: [ 0.990576] domain 0: span 3,7 level SIBLING [ 0.990835] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 0.991289] domain 1: span 0-7 level MC [ 0.991536] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.992323] CPU4 attaching sched-domain: [ 0.992533] domain 0: span 0,4 level SIBLING [ 0.992792] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 0.993238] domain 1: span 0-7 level MC [ 0.993485] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.994270] CPU5 attaching sched-domain: [ 0.994480] domain 0: span 1,5 level SIBLING [ 0.994739] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 0.995193] domain 1: span 0-7 level MC [ 0.995440] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.996226] CPU6 attaching sched-domain: [ 0.996436] domain 0: span 2,6 level SIBLING [ 0.996695] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 0.997141] domain 1: span 0-7 level MC [ 0.997388] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.998175] CPU7 attaching sched-domain: [ 0.998384] domain 0: span 3,7 level SIBLING [ 0.998643] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 0.999095] domain 1: span 0-7 level MC [ 0.999342] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 1.001200] devtmpfs: initialized [ 1.001881] kworker/u:0 used greatest stack depth: 5032 bytes left [ 1.002179] kworker/u:0 used greatest stack depth: 4944 bytes left [ 1.002477] kworker/u:0 used greatest stack depth: 4584 bytes left [ 1.006418] gcov: version magic: 0x3430352a [ 1.008103] PM: Registering ACPI NVS region at bcde3000 (2195456 bytes) [ 1.008481] PM: Registering ACPI NVS region at bf714000 (700416 bytes) [ 1.009831] RTC time: 16:03:30, date: 08/08/11 [ 1.010241] NET: Registered protocol family 16 [ 1.012112] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 1.012501] ACPI: bus type pci registered [ 1.013131] dca service started, version 1.12.1 [ 1.013525] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 1.013966] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 1.035193] PCI: Using configuration type 1 for base access [ 1.104903] bio: create slab at 0 [ 1.105501] ACPI: Added _OSI(Module Device) [ 1.105724] ACPI: Added _OSI(Processor Device) [ 1.105955] ACPI: Added _OSI(3.0 _SCP Extensions) [ 1.106195] ACPI: Added _OSI(Processor Aggregator Device) [ 1.116140] ACPI: EC: Look up EC in DSDT [ 1.166052] ACPI: Interpreter enabled [ 1.166255] ACPI: (supports S0 S1 S3 S4 S5) [ 1.166762] ACPI: Using IOAPIC for interrupt routing [ 1.194069] ACPI: No dock devices found. [ 1.194281] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.196267] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 1.199727] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 1.200039] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 1.200348] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.200714] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 1.201080] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 1.201445] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 1.201861] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 1.202269] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 1.202760] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.203057] pci 0000:00:01.0: PME# disabled [ 1.203313] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 1.203684] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 1.203978] pci 0000:00:03.0: PME# disabled [ 1.204237] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 1.204608] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 1.204902] pci 0000:00:07.0: PME# disabled [ 1.205164] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 1.205564] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 1.205965] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 1.206393] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 1.206808] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 1.207202] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 1.207606] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 1.207917] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 1.208220] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 1.208522] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 1.208869] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.209162] pci 0000:00:19.0: PME# disabled [ 1.209407] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 1.209764] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 1.210105] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 1.210473] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 1.210817] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 1.211176] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 1.211529] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 1.211842] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 1.212249] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 1.212543] pci 0000:00:1a.7: PME# disabled [ 1.212797] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 1.213104] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 1.213513] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.213806] pci 0000:00:1b.0: PME# disabled [ 1.214055] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 1.214462] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.214756] pci 0000:00:1c.0: PME# disabled [ 1.215008] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 1.215391] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.215685] pci 0000:00:1c.1: PME# disabled [ 1.215942] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 1.216325] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.216619] pci 0000:00:1c.4: PME# disabled [ 1.216878] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 1.217235] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 1.217575] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 1.217933] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 1.218281] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 1.218642] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 1.218997] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 1.219310] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 1.219717] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 1.220011] pci 0000:00:1d.7: PME# disabled [ 1.220258] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 1.220647] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 1.221086] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 1.221419] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 1.221797] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 1.222244] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 1.222559] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 1.222835] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 1.223112] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 1.223389] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 1.223664] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 1.223941] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 1.224286] pci 0000:00:1f.2: PME# supported from D3hot [ 1.224548] pci 0000:00:1f.2: PME# disabled [ 1.224793] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 1.225102] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 1.225447] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 1.225825] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.226177] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 1.226486] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 1.226788] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 1.227150] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 1.227490] pci 0000:02:00.0: supports D1 D2 [ 1.227745] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 1.228045] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 1.228436] pci 0000:02:00.1: supports D1 D2 [ 1.228686] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.228950] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.229271] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.230321] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.230665] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.231013] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.231389] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 1.231702] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 1.231988] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 1.232274] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 1.232559] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 1.232844] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 1.233129] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 1.233509] pci 0000:06:00.0: supports D1 [ 1.233722] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 1.234005] pci 0000:06:00.0: PME# disabled [ 1.234290] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.234554] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.234848] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.235231] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 1.235542] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 1.235846] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 1.236236] pci 0000:07:03.0: supports D1 D2 [ 1.236459] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 1.236782] pci 0000:07:03.0: PME# disabled [ 1.237082] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 1.237414] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.237737] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.238125] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.238523] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.238937] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 1.239351] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 1.239765] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 1.240232] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.243287] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 1.244266] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 1.244789] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 1.245310] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 1.245831] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 1.246385] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 1.246934] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 1.247671] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19) [ 1.306046] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.307091] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.308127] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.309165] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.310253] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.311290] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.312327] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.313363] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.315068] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.315475] vgaarb: loaded [ 1.315640] vgaarb: bridge control possible 0000:02:00.0 [ 1.316296] SCSI subsystem initialized [ 1.316895] libata version 3.00 loaded. [ 1.317697] usbcore: registered new interface driver usbfs [ 1.318364] usbcore: registered new interface driver hub [ 1.318789] usbcore: registered new device driver usb [ 1.319961] wmi: Mapper loaded [ 1.320310] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 1.320729] PCI: Using ACPI for IRQ routing [ 1.322993] PCI: Discovered peer bus 3f [ 1.323364] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600 [ 1.323700] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600 [ 1.324042] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600 [ 1.324374] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600 [ 1.324714] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600 [ 1.325046] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600 [ 1.325385] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600 [ 1.325721] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600 [ 1.326069] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600 [ 1.326402] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600 [ 1.326733] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600 [ 1.327071] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600 [ 1.327402] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600 [ 1.327733] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600 [ 1.328065] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600 [ 1.328403] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600 [ 1.328734] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600 [ 1.329065] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600 [ 1.329396] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600 [ 1.332856] PCI: pci_cache_line_size set to 64 bytes [ 1.333551] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 1.333821] reserve RAM buffer: 00000000bcde3000 - 00000000bfffffff [ 1.334170] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff [ 1.334509] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff [ 1.334845] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff [ 1.335181] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff [ 1.388321] pnp: PnP ACPI init [ 1.388609] ACPI: bus type pnp registered [ 1.390293] pnp 00:00: [bus 00-3d] [ 1.390491] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.390707] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.390946] pnp 00:00: [io 0x0d00-0xffff window] [ 1.391186] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.391450] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 1.391714] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 1.391980] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 1.392244] pnp 00:00: [mem 0x00000000 window] [ 1.392728] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 1.393622] pnp 00:01: [io 0x0000-0x000f] [ 1.393850] pnp 00:01: [io 0x0081-0x0083] [ 1.394067] pnp 00:01: [io 0x0087] [ 1.394260] pnp 00:01: [io 0x0089-0x008b] [ 1.394476] pnp 00:01: [io 0x008f] [ 1.394670] pnp 00:01: [io 0x00c0-0x00df] [ 1.394887] pnp 00:01: [dma 4] [ 1.395250] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.395587] pnp 00:02: [io 0x0070-0x0071] [ 1.395803] pnp 00:02: [io 0x0074-0x0077] [ 1.396026] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 1.396422] pnp 00:02: [irq 8] [ 1.396786] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.397136] pnp 00:03: [io 0x00f0] [ 1.397334] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 1.397746] pnp 00:03: [irq 13] [ 1.398119] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.398465] pnp 00:04: [io 0x0061] [ 1.398849] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.399188] pnp 00:05: [io 0x0500-0x053f] [ 1.399404] pnp 00:05: [io 0x0400-0x047f] [ 1.399620] pnp 00:05: [io 0x0092] [ 1.399813] pnp 00:05: [io 0x0680-0x06ff] [ 1.400029] pnp 00:05: [io 0x0010-0x001f] [ 1.400245] pnp 00:05: [io 0x0072-0x0073] [ 1.400460] pnp 00:05: [io 0x0080] [ 1.400654] pnp 00:05: [io 0x0084-0x0086] [ 1.400870] pnp 00:05: [io 0x0088] [ 1.401064] pnp 00:05: [io 0x008c-0x008e] [ 1.401280] pnp 00:05: [io 0x0090-0x009f] [ 1.401902] system 00:05: [io 0x0500-0x053f] has been reserved [ 1.402189] system 00:05: [io 0x0400-0x047f] has been reserved [ 1.402473] system 00:05: [io 0x0680-0x06ff] has been reserved [ 1.402761] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.403227] pnp 00:06: [io 0x0060] [ 1.403422] pnp 00:06: [io 0x0064] [ 1.403952] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.405294] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 1.405777] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 1.406367] pnp: PnP ACPI: found 8 devices [ 1.406585] ACPI: ACPI bus type pnp unregistered [ 1.425084] Switching to clocksource acpi_pm [ 1.425646] Switched to NOHz mode on CPU #0 [ 1.425656] Switched to NOHz mode on CPU #2 [ 1.425680] Switched to NOHz mode on CPU #5 [ 1.425688] Switched to NOHz mode on CPU #3 [ 1.425696] Switched to NOHz mode on CPU #6 [ 1.425704] Switched to NOHz mode on CPU #1 [ 1.425708] Switched to NOHz mode on CPU #7 [ 1.425769] Switched to NOHz mode on CPU #4 [ 1.427442] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 1.427917] PCI: max bus depth: 1 pci_try_num: 2 [ 1.428234] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.428509] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 1.428873] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.429136] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.429487] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.429876] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.430147] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.430420] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.430693] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.431525] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.431821] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.432146] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 1.432878] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.433224] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0) [ 1.433638] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.433956] pci 0000:00:01.0: setting latency timer to 64 [ 1.434228] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.434544] pci 0000:00:03.0: setting latency timer to 64 [ 1.434816] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.435133] pci 0000:00:07.0: setting latency timer to 64 [ 1.435413] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0) [ 1.435811] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.436130] pci 0000:00:1c.0: setting latency timer to 64 [ 1.436404] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 1.436722] pci 0000:00:1c.1: setting latency timer to 64 [ 1.436995] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.437327] pci 0000:00:1c.4: setting latency timer to 64 [ 1.437602] pci 0000:00:1e.0: setting latency timer to 64 [ 1.437869] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.438140] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.438410] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.438707] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.439003] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.439299] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.439595] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 1.439892] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.440254] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 1.440524] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 1.440821] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 1.441117] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 1.441410] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 1.441681] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 1.441977] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.442272] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.442568] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.442864] pci_bus 0000:3f: resource 0 [io 0x0000-0xffff] [ 1.443134] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff] [ 1.443519] NET: Registered protocol family 2 [ 1.444184] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.447094] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.450730] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) [ 1.458762] TCP: Hash tables configured (established 524288 bind 65536) [ 1.459101] TCP reno registered [ 1.459366] UDP hash table entries: 2048 (order: 6, 393216 bytes) [ 1.460185] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes) [ 1.461230] NET: Registered protocol family 1 [ 1.461869] RPC: Registered named UNIX socket transport module. [ 1.462156] RPC: Registered udp transport module. [ 1.462395] RPC: Registered tcp transport module. [ 1.462634] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.463006] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.463312] pci 0000:00:1a.0: Performing full reset [ 1.463578] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.463884] pci 0000:00:1a.1: Performing full reset [ 1.464150] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.464456] pci 0000:00:1a.2: Performing full reset [ 1.464905] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.465232] pci 0000:00:1d.0: Performing full reset [ 1.465498] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.465804] pci 0000:00:1d.1: Performing full reset [ 1.466069] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.466375] pci 0000:00:1d.2: Performing full reset [ 1.466808] pci 0000:02:00.0: Boot video device [ 1.467146] PCI: CLS 64 bytes, default 64 [ 1.475283] Machine check injector initialized [ 1.479405] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 1.479702] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 1.479997] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 1.480291] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 1.480586] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 1.480884] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 1.481226] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 1.481519] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 1.482001] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 1.484751] Initializing RT-Tester: OK [ 1.485218] audit: initializing netlink socket (disabled) [ 1.485521] type=2000 audit(1312819410.264:1): initialized [ 1.633196] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.657078] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.658191] fuse init (API version 7.16) [ 1.659111] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.664352] Btrfs loaded [ 1.664521] msgmni has been set to 5858 [ 1.666862] io scheduler noop registered [ 1.667075] io scheduler deadline registered [ 1.667568] io scheduler cfq registered (default) [ 1.667824] start plist test [ 1.669390] end plist test [ 1.670374] pcieport 0000:00:1c.0: setting latency timer to 64 [ 1.670761] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 1.671252] pcieport 0000:00:1c.1: setting latency timer to 64 [ 1.671607] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 1.672096] pcieport 0000:00:1c.4: setting latency timer to 64 [ 1.672449] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 1.673454] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.675269] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 1.675719] ACPI: Sleep Button [SLPB] [ 1.676202] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.676607] ACPI: Power Button [PWRF] [ 1.678366] ACPI: acpi_idle registered with cpuidle [ 1.679589] Monitor-Mwait will be used to enter C-1 state [ 1.679954] Monitor-Mwait will be used to enter C-3 state [ 1.696334] ioatdma: Intel(R) QuickData Technology Driver 4.00 [ 1.803411] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.884030] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 2.071928] Initializing Nozomi driver 2.1d [ 2.073307] Non-volatile memory driver v1.3 [ 2.074412] Linux agpgart interface v0.103 [ 2.075194] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 2.075642] Hangcheck: Using getrawmonotonic(). [ 2.076033] [drm] Initialized drm 1.1.0 20060810 [ 2.076269] drm/i810 does not support SMP [ 2.076483] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 2.462299] Refined TSC clocksource calibration: 3200.113 MHz. [ 2.462615] Switching to clocksource tsc [ 5.086148] floppy0: no floppy controllers found [ 5.607405] brd: module loaded [ 5.611125] loop: module loaded [ 5.612035] Loading iSCSI transport class v2.0-870. [ 5.613320] ahci 0000:00:1f.2: version 3.0 [ 5.613573] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0) [ 5.613984] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 5.614369] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 5.614737] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 5.615137] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 5.615529] ahci 0000:00:1f.2: setting latency timer to 64 [ 5.655617] scsi0 : ahci [ 5.656293] scsi1 : ahci [ 5.656826] scsi2 : ahci [ 5.657361] scsi3 : ahci [ 5.657892] scsi4 : ahci [ 5.658424] scsi5 : ahci [ 5.659618] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43 [ 5.659990] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43 [ 5.660370] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 5.660741] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 5.661109] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 5.661480] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 5.661939] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.662306] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 5.662801] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 5.663123] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 5.663445] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 5.663747] ahci: SSS flag set, parallel bus scan disabled [ 5.664054] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 5.664467] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 5.664763] ahci 0000:06:00.0: setting latency timer to 64 [ 5.666813] scsi6 : ahci [ 5.667335] scsi7 : ahci [ 5.667884] scsi8 : ahci [ 5.668488] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 5.668861] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 5.669230] ata9: DUMMY [ 5.675301] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 5.675628] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 5.676690] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k [ 5.676974] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 5.677301] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0) [ 5.677701] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 5.678031] e1000e 0000:00:19.0: setting latency timer to 64 [ 5.678467] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.868675] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54 [ 5.869069] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 5.869450] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 5.869940] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k [ 5.870247] Copyright (c) 2007-2011 Intel Corporation. [ 5.870681] Intel(R) Virtual Function Network Driver - version 2.0.0-k [ 5.870987] Copyright (c) 2009 - 2010 Intel Corporation. [ 5.871423] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k [ 5.871825] ixgbe: Copyright (c) 1999-2011 Intel Corporation. [ 5.872304] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 5.872633] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 5.873837] jme: JMicron JMC2XX ethernet driver version 1.0.8 [ 5.874857] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 5.875762] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011) [ 5.876440] sky2: driver version 1.29 [ 5.878902] tun: Universal TUN/TAP device driver, 1.6 [ 5.879155] tun: (C) 1999-2004 Max Krasnyansky [ 5.880218] usbcore: registered new interface driver catc [ 5.880483] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 5.880888] usbcore: registered new interface driver kaweth [ 5.881160] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 5.881654] usbcore: registered new interface driver pegasus [ 5.881928] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 5.882371] usbcore: registered new interface driver rtl8150 [ 5.882772] usbcore: registered new interface driver asix [ 5.883160] usbcore: registered new interface driver cdc_ether [ 5.883694] usbcore: registered new interface driver cdc_eem [ 5.884108] usbcore: registered new interface driver dm9601 [ 5.884530] usbcore: registered new interface driver smsc75xx [ 5.884954] usbcore: registered new interface driver smsc95xx [ 5.885368] usbcore: registered new interface driver gl620a [ 5.885776] usbcore: registered new interface driver net1080 [ 5.886187] usbcore: registered new interface driver plusb [ 5.886592] usbcore: registered new interface driver rndis_host [ 5.887013] usbcore: registered new interface driver cdc_subset [ 5.887437] usbcore: registered new interface driver zaurus [ 5.887863] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 5.888372] usbcore: registered new interface driver int51x1 [ 5.888781] usbcore: registered new interface driver ipheth [ 5.889199] usbcore: registered new interface driver sierra_net [ 5.889484] cdc_ncm: 01-June-2011 [ 5.889813] usbcore: registered new interface driver cdc_ncm [ 5.890089] netconsole: local port 6665 [ 5.890297] netconsole: local IP 10.0.0.0 [ 5.890509] netconsole: interface 'eth0' [ 5.890719] netconsole: remote port 6666 [ 5.890929] netconsole: remote IP 192.168.1.1 [ 5.891154] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 5.891445] netconsole: device eth0 not up yet, forcing it [ 5.979289] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.979617] ata6: SATA link down (SStatus 0 SControl 300) [ 5.979915] ata3: SATA link down (SStatus 0 SControl 300) [ 5.980242] ata5: SATA link down (SStatus 0 SControl 300) [ 5.980651] ata4: SATA link down (SStatus 0 SControl 300) [ 5.983572] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.987234] ata7: SATA link down (SStatus 0 SControl 300) [ 6.026435] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 6.026711] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 6.039148] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 6.084548] ata1.00: configured for UDMA/133 [ 6.085303] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 6.086689] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 6.087250] sd 0:0:0:0: [sda] Write Protect is off [ 6.087493] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 6.087811] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.176295] sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 > [ 6.179378] sd 0:0:0:0: [sda] Attached SCSI disk [ 6.314237] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 6.379945] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 6.380250] ata2.00: applying bridge limits [ 6.411124] ata2.00: configured for UDMA/33 [ 6.412488] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 6.728933] ata8: SATA link down (SStatus 0 SControl 300) [ 9.042614] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 9.049577] console [netcon0] enabled [ 9.049791] netconsole: network logging started [ 9.050405] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.050714] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 9.051065] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0) [ 9.051468] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 9.051816] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 9.052101] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 9.052657] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file 'devices' [ 9.053097] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.053446] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 9.053840] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 9.054271] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 9.054775] ehci_hcd 0000:00:1a.7: debug port 1 [ 9.055013] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.059315] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 9.059634] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 9.059953] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 9.060231] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.064541] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 9.073662] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 9.074135] usb usb1: default language 0x0409 [ 9.074406] usb usb1: udev 1, busnum 1, minor = 0 [ 9.074647] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 9.074965] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.075330] usb usb1: Product: EHCI Host Controller [ 9.075577] usb usb1: Manufacturer: Linux 3.0.0-sound+ ehci_hcd [ 9.075861] usb usb1: SerialNumber: 0000:00:1a.7 [ 9.076607] usb usb1: usb_probe_device [ 9.076815] usb usb1: configuration #1 chosen from 1 choice [ 9.077205] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 9.077761] hub 1-0:1.0: usb_probe_interface [ 9.077988] hub 1-0:1.0: usb_probe_interface - got id [ 9.078241] hub 1-0:1.0: USB hub found [ 9.078496] hub 1-0:1.0: 6 ports detected [ 9.078712] hub 1-0:1.0: standalone hub [ 9.078920] hub 1-0:1.0: no power switching (usb 1.0) [ 9.079173] hub 1-0:1.0: individual port over-current protection [ 9.079462] hub 1-0:1.0: power on to power good time: 20ms [ 9.079833] hub 1-0:1.0: local power source is good [ 9.080082] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 9.080497] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.081110] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0) [ 9.081513] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 9.081874] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 9.082160] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 9.082431] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '002' [ 9.082761] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 9.083141] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 9.083571] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 9.084047] ehci_hcd 0000:00:1d.7: debug port 1 [ 9.084284] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.088583] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 9.088901] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 9.089220] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 9.089498] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.093809] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 9.105552] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 9.105907] usb usb2: default language 0x0409 [ 9.106160] usb usb2: udev 1, busnum 2, minor = 128 [ 9.106407] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 9.106724] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.107088] usb usb2: Product: EHCI Host Controller [ 9.107335] usb usb2: Manufacturer: Linux 3.0.0-sound+ ehci_hcd [ 9.107621] usb usb2: SerialNumber: 0000:00:1d.7 [ 9.108168] usb usb2: usb_probe_device [ 9.108377] usb usb2: configuration #1 chosen from 1 choice [ 9.108665] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 9.109117] hub 2-0:1.0: usb_probe_interface [ 9.109344] hub 2-0:1.0: usb_probe_interface - got id [ 9.109607] hub 2-0:1.0: USB hub found [ 9.109826] hub 2-0:1.0: 6 ports detected [ 9.110613] hub 2-0:1.0: standalone hub [ 9.110821] hub 2-0:1.0: no power switching (usb 1.0) [ 9.111074] hub 2-0:1.0: individual port over-current protection [ 9.111362] hub 2-0:1.0: power on to power good time: 20ms [ 9.111648] hub 2-0:1.0: local power source is good [ 9.111895] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 9.112300] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.112983] uhci_hcd: USB Universal Host Controller Interface driver [ 9.113355] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.113705] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 9.113991] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 9.114262] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '003' [ 9.114592] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 9.114972] uhci_hcd 0000:00:1a.0: detected 2 ports [ 9.115224] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.115538] uhci_hcd 0000:00:1a.0: Performing full reset [ 9.115814] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 9.116102] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 9.116469] usb usb3: default language 0x0409 [ 9.116722] usb usb3: udev 1, busnum 3, minor = 256 [ 9.116969] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.117286] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.117661] usb usb3: Product: UHCI Host Controller [ 9.117909] usb usb3: Manufacturer: Linux 3.0.0-sound+ uhci_hcd [ 9.118194] usb usb3: SerialNumber: 0000:00:1a.0 [ 9.118741] usb usb3: usb_probe_device [ 9.118950] usb usb3: configuration #1 chosen from 1 choice [ 9.119237] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 9.119687] hub 3-0:1.0: usb_probe_interface [ 9.119913] hub 3-0:1.0: usb_probe_interface - got id [ 9.120166] hub 3-0:1.0: USB hub found [ 9.120385] hub 3-0:1.0: 2 ports detected [ 9.120600] hub 3-0:1.0: standalone hub [ 9.120808] hub 3-0:1.0: no power switching (usb 1.0) [ 9.121061] hub 3-0:1.0: individual port over-current protection [ 9.121350] hub 3-0:1.0: power on to power good time: 2ms [ 9.121653] hub 3-0:1.0: local power source is good [ 9.121902] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 9.122271] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.122692] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 9.123113] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0) [ 9.123515] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 9.123854] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 9.124139] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 9.124408] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '004' [ 9.124738] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 9.125118] uhci_hcd 0000:00:1a.1: detected 2 ports [ 9.125368] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.125693] uhci_hcd 0000:00:1a.1: Performing full reset [ 9.125970] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 9.126286] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 9.126634] usb usb4: default language 0x0409 [ 9.126887] usb usb4: udev 1, busnum 4, minor = 384 [ 9.127135] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.127452] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.127817] usb usb4: Product: UHCI Host Controller [ 9.128064] usb usb4: Manufacturer: Linux 3.0.0-sound+ uhci_hcd [ 9.128348] usb usb4: SerialNumber: 0000:00:1a.1 [ 9.128894] usb usb4: usb_probe_device [ 9.129102] usb usb4: configuration #1 chosen from 1 choice [ 9.129389] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 9.129851] hub 4-0:1.0: usb_probe_interface [ 9.130077] hub 4-0:1.0: usb_probe_interface - got id [ 9.130331] hub 4-0:1.0: USB hub found [ 9.130549] hub 4-0:1.0: 2 ports detected [ 9.130764] hub 4-0:1.0: standalone hub [ 9.130972] hub 4-0:1.0: no power switching (usb 1.0) [ 9.131226] hub 4-0:1.0: individual port over-current protection [ 9.131515] hub 4-0:1.0: power on to power good time: 2ms [ 9.131797] hub 4-0:1.0: local power source is good [ 9.132045] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 9.132413] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.132830] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 9.133243] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 9.133592] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 9.133878] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 9.134149] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '005' [ 9.134478] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 9.134858] uhci_hcd 0000:00:1a.2: detected 2 ports [ 9.135109] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.135423] uhci_hcd 0000:00:1a.2: Performing full reset [ 9.135699] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 9.136019] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 9.136367] usb usb5: default language 0x0409 [ 9.136621] usb usb5: udev 1, busnum 5, minor = 512 [ 9.136868] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.137185] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.137558] usb usb5: Product: UHCI Host Controller [ 9.137805] usb usb5: Manufacturer: Linux 3.0.0-sound+ uhci_hcd [ 9.138090] usb usb5: SerialNumber: 0000:00:1a.2 [ 9.138635] usb usb5: usb_probe_device [ 9.138843] usb usb5: configuration #1 chosen from 1 choice [ 9.139131] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 9.139577] hub 5-0:1.0: usb_probe_interface [ 9.139802] hub 5-0:1.0: usb_probe_interface - got id [ 9.140055] hub 5-0:1.0: USB hub found [ 9.140272] hub 5-0:1.0: 2 ports detected [ 9.140486] hub 5-0:1.0: standalone hub [ 9.140694] hub 5-0:1.0: no power switching (usb 1.0) [ 9.140947] hub 5-0:1.0: individual port over-current protection [ 9.141237] hub 5-0:1.0: power on to power good time: 2ms [ 9.141529] hub 5-0:1.0: local power source is good [ 9.141777] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 9.142148] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.142568] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 9.142986] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 9.143325] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 9.143610] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 9.143880] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '006' [ 9.144210] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 9.144590] uhci_hcd 0000:00:1d.0: detected 2 ports [ 9.144842] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.145157] uhci_hcd 0000:00:1d.0: Performing full reset [ 9.145442] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 9.145730] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 9.146078] usb usb6: default language 0x0409 [ 9.146331] usb usb6: udev 1, busnum 6, minor = 640 [ 9.146579] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.146896] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.147262] usb usb6: Product: UHCI Host Controller [ 9.147508] usb usb6: Manufacturer: Linux 3.0.0-sound+ uhci_hcd [ 9.147793] usb usb6: SerialNumber: 0000:00:1d.0 [ 9.148344] usb usb6: usb_probe_device [ 9.148552] usb usb6: configuration #1 chosen from 1 choice [ 9.148840] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 9.149290] hub 6-0:1.0: usb_probe_interface [ 9.149527] hub 6-0:1.0: usb_probe_interface - got id [ 9.149780] hub 6-0:1.0: USB hub found [ 9.149998] hub 6-0:1.0: 2 ports detected [ 9.150213] hub 6-0:1.0: standalone hub [ 9.150421] hub 6-0:1.0: no power switching (usb 1.0) [ 9.150673] hub 6-0:1.0: individual port over-current protection [ 9.150962] hub 6-0:1.0: power on to power good time: 2ms [ 9.151243] hub 6-0:1.0: local power source is good [ 9.151490] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 9.151862] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.152302] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 9.152692] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 9.153030] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 9.153314] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 9.153594] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '007' [ 9.153959] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 9.154343] uhci_hcd 0000:00:1d.1: detected 2 ports [ 9.154594] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.154909] uhci_hcd 0000:00:1d.1: Performing full reset [ 9.155185] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 9.155472] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 9.155817] usb usb7: default language 0x0409 [ 9.156070] usb usb7: udev 1, busnum 7, minor = 768 [ 9.156317] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.156635] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.156999] usb usb7: Product: UHCI Host Controller [ 9.157246] usb usb7: Manufacturer: Linux 3.0.0-sound+ uhci_hcd [ 9.157540] usb usb7: SerialNumber: 0000:00:1d.1 [ 9.158099] usb usb7: usb_probe_device [ 9.158307] usb usb7: configuration #1 chosen from 1 choice [ 9.158594] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 9.159042] hub 7-0:1.0: usb_probe_interface [ 9.159268] hub 7-0:1.0: usb_probe_interface - got id [ 9.159521] hub 7-0:1.0: USB hub found [ 9.159739] hub 7-0:1.0: 2 ports detected [ 9.159954] hub 7-0:1.0: standalone hub [ 9.160162] hub 7-0:1.0: no power switching (usb 1.0) [ 9.160414] hub 7-0:1.0: individual port over-current protection [ 9.160702] hub 7-0:1.0: power on to power good time: 2ms [ 9.160984] hub 7-0:1.0: local power source is good [ 9.161231] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 9.161614] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.162054] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 9.163012] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 9.163351] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 9.163635] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 9.163905] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '008' [ 9.164234] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 9.164615] uhci_hcd 0000:00:1d.2: detected 2 ports [ 9.164866] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 9.165180] uhci_hcd 0000:00:1d.2: Performing full reset [ 9.165465] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 9.165752] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 9.166098] usb usb8: default language 0x0409 [ 9.166351] usb usb8: udev 1, busnum 8, minor = 896 [ 9.166598] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 9.166915] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.167279] usb usb8: Product: UHCI Host Controller [ 9.167526] usb usb8: Manufacturer: Linux 3.0.0-sound+ uhci_hcd [ 9.167811] usb usb8: SerialNumber: 0000:00:1d.2 [ 9.168357] usb usb8: usb_probe_device [ 9.168565] usb usb8: configuration #1 chosen from 1 choice [ 9.168853] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 9.169327] hub 8-0:1.0: usb_probe_interface [ 9.169554] hub 8-0:1.0: usb_probe_interface - got id [ 9.169807] hub 8-0:1.0: USB hub found [ 9.170024] hub 8-0:1.0: 2 ports detected [ 9.170239] hub 8-0:1.0: standalone hub [ 9.170447] hub 8-0:1.0: no power switching (usb 1.0) [ 9.170700] hub 8-0:1.0: individual port over-current protection [ 9.170988] hub 8-0:1.0: power on to power good time: 2ms [ 9.171270] hub 8-0:1.0: local power source is good [ 9.171518] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 9.171885] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '001' [ 9.172329] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 9.172875] Initializing USB Mass Storage driver... [ 9.173326] usbcore: registered new interface driver usb-storage [ 9.173616] USB Mass Storage support registered. [ 9.174124] usbcore: registered new interface driver libusual [ 9.174550] usbcore: registered new interface driver ums-alauda [ 9.174978] usbcore: registered new interface driver ums-cypress [ 9.175406] usbcore: registered new interface driver ums-datafab [ 9.175841] usbcore: registered new interface driver ums-freecom [ 9.176275] usbcore: registered new interface driver ums-isd200 [ 9.176702] usbcore: registered new interface driver ums-jumpshot [ 9.177137] usbcore: registered new interface driver ums-karma [ 9.177521] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 9.177953] hub 1-0:1.0: port 1: status 0501 change 0001 [ 9.178256] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 9.178685] hub 1-0:1.0: port 2: status 0501 change 0001 [ 9.178971] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0 ACK POWER sig=j CSC CONNECT [ 9.179399] hub 1-0:1.0: port 4: status 0501 change 0001 [ 9.179855] usbcore: registered new interface driver ums-onetouch [ 9.180301] usbcore: registered new interface driver ums-sddr09 [ 9.180740] usbcore: registered new interface driver ums-sddr55 [ 9.181181] usbcore: registered new interface driver ums-usbat [ 9.182041] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 9.185602] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 9.185911] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 9.187266] mousedev: PS/2 mouse device common for all mice [ 9.189189] rtc_cmos 00:02: RTC can wake from S4 [ 9.189894] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 9.190226] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 9.190634] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 9.191281] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 9.191903] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 9.192197] iTCO_vendor_support: vendor-support=0 [ 9.192440] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 9.195918] cpuidle: using governor ladder [ 9.202766] cpuidle: using governor menu [ 9.203465] usbcore: registered new interface driver usbhid [ 9.203740] usbhid: USB HID core driver [ 9.204740] dell_wmi: No known WMI GUID found [ 9.204971] acer_wmi: Acer Laptop ACPI-WMI Extras [ 9.205236] acer_wmi: No or unsupported WMI interface, unable to load [ 9.209406] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 9.209968] ASIHPI driver 4.08.00 [ 9.210912] ALSA aw2-alsa.c:222 aw2: Load aw2 module [ 9.215254] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0) [ 9.215659] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 9.216110] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 9.216441] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 9.216743] ALSA hda_intel.c:2620 chipset global capabilities = 0x4401 [ 9.217066] ALSA hda_intel.c:1097 Clearing TCSEL [ 9.221218] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 9.221521] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 9.229208] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00 [ 9.241253] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 9.249186] ALSA hda_intel.c:951 codec_mask = 0x4 [ 9.249469] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 9.249916] ALSA hda_intel.c:1398 codec #2 probed OK [ 9.261204] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 9.261305] ALSA hda_codec.c:3962 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 9.261309] hda_codec: ALC889: SKU not ready 0x411111f0 [ 9.261672] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 9.265889] ALSA hda_codec.c:2346 Cannot find slave Side Playback Volume, skipped [ 9.266270] ALSA hda_codec.c:2346 Cannot find slave Headphone Playback Volume, skipped [ 9.266663] ALSA hda_codec.c:2346 Cannot find slave Mono Playback Volume, skipped [ 9.267037] ALSA hda_codec.c:2346 Cannot find slave Line-Out Playback Volume, skipped [ 9.267431] ALSA hda_codec.c:2346 Cannot find slave Side Playback Switch, skipped [ 9.267807] ALSA hda_codec.c:2346 Cannot find slave Mono Playback Switch, skipped [ 9.268183] ALSA hda_codec.c:2346 Cannot find slave Line-Out Playback Switch, skipped [ 9.269107] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 9.270508] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 9.272361] usbcore: registered new interface driver snd-usb-audio [ 9.272818] usbcore: registered new interface driver snd-ua101 [ 9.273326] usbcore: registered new interface driver snd-usb-usx2y [ 9.273804] usbcore: registered new interface driver snd-usb-us122l [ 9.274271] usbcore: registered new interface driver snd-usb-caiaq [ 9.274567] ALSA device list: [ 9.274743] #0: HDA Intel at 0xf7f00000 irq 45 [ 9.274982] oprofile: using NMI interrupt. [ 9.275275] netem: version 1.3 [ 9.276627] TCP bic registered [ 9.276810] TCP cubic registered [ 9.277022] TCP westwood registered [ 9.277094] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000 [ 9.277142] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 9.277815] TCP highspeed registered [ 9.278024] TCP hybla registered [ 9.278221] TCP htcp registered [ 9.278413] TCP vegas registered [ 9.278610] TCP veno registered [ 9.278802] TCP scalable registered [ 9.279008] TCP lp registered [ 9.279194] TCP yeah registered [ 9.279388] TCP illinois registered [ 9.279592] Initializing XFRM netlink socket [ 9.281734] NET: Registered protocol family 10 [ 9.286446] IPv6 over IPv4 tunneling driver [ 9.289084] NET: Registered protocol family 17 [ 9.289335] NET: Registered protocol family 15 [ 9.289663] [ 9.289664] printing PIC contents [ 9.289978] ... PIC IMR: ffff [ 9.290159] ... PIC IRR: 0c21 [ 9.290345] ... PIC ISR: 0000 [ 9.290526] ... PIC ELCR: 0c20 [ 9.290709] printing local APIC contents on CPU#0/0: [ 9.290961] ... APIC ID: 00000000 (0) [ 9.291178] ... APIC VERSION: 00060015 [ 9.291382] ... APIC TASKPRI: 00000000 (00) [ 9.291602] ... APIC PROCPRI: 00000000 [ 9.291806] ... APIC LDR: 01000000 [ 9.291996] ... APIC DFR: ffffffff [ 9.292187] ... APIC SPIV: 000001ff [ 9.292382] ... APIC ISR field: [ 9.292564] 0000000000000000000000000000000000000000000000000000000000000000 [ 9.293170] ... APIC TMR field: [ 9.293353] 0000000000000000000000000000000000020000000000000000000000000000 [ 9.293957] ... APIC IRR field: [ 9.294139] 0000000000010000000000000000000000000200000000000000000000000000 [ 9.294741] ... APIC ESR: 00000000 [ 9.294932] ... APIC ICR: 000000ef [ 9.295123] ... APIC ICR2: 07000000 [ 9.295318] ... APIC LVTT: 000000ef [ 9.295513] ... APIC LVTPC: 00000400 [ 9.295713] ... APIC LVT0: 00010700 [ 9.295907] ... APIC LVT1: 00000400 [ 9.296102] ... APIC LVTERR: 000000fe [ 9.296302] ... APIC TMICT: 00e01dac [ 9.296501] ... APIC TMCCT: 00da4248 [ 9.296698] ... APIC TDCR: 00000003 [ 9.296892] [ 9.297013] number of MP IRQ sources: 15. [ 9.297232] number of IO-APIC #8 registers: 24. [ 9.298038] testing the IO APIC....................... [ 9.298301] [ 9.298422] IO APIC #8...... [ 9.298596] .... register #00: 08000000 [ 9.298803] ....... : physical APIC id: 08 [ 9.299031] ....... : Delivery Type: 0 [ 9.299246] ....... : LTS : 0 [ 9.299460] .... register #01: 00170020 [ 9.299668] ....... : max redirection entries: 17 [ 9.299920] ....... : PRQ implemented: 0 [ 9.300144] ....... : IO APIC version: 20 [ 9.300371] .... IRQ redirection table: [ 9.300578] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 9.300851] 00 00 1 0 0 0 0 0 0 00 [ 9.301381] 01 00 0 0 0 0 0 0 0 31 [ 9.301680] 02 00 0 0 0 0 0 0 0 30 [ 9.301980] 03 00 0 0 0 0 0 0 0 33 [ 9.302279] 04 00 0 0 0 0 0 0 0 34 [ 9.302578] 05 00 0 0 0 0 0 0 0 35 [ 9.302877] 06 00 1 0 0 0 0 0 0 36 [ 9.303177] 07 00 0 0 0 0 0 0 0 37 [ 9.303475] 08 00 0 0 0 0 0 0 0 38 [ 9.303775] 09 00 0 1 0 0 0 0 0 39 [ 9.304074] 0a 00 0 0 0 0 0 0 0 3A [ 9.304374] 0b 00 0 0 0 0 0 0 0 3B [ 9.304673] 0c 00 0 0 0 0 0 0 0 3C [ 9.304987] 0d 00 0 0 0 0 0 0 0 3D [ 9.305286] 0e 00 0 0 0 0 0 0 0 3E [ 9.305584] 0f 00 0 0 0 0 0 0 0 3F [ 9.305883] 10 00 0 1 0 1 0 0 0 29 [ 9.306182] 11 00 1 1 0 1 0 0 0 41 [ 9.306481] 12 00 0 1 0 1 0 0 0 91 [ 9.306780] 13 00 0 1 0 1 0 0 0 61 [ 9.307080] 14 00 1 1 0 1 0 0 0 71 [ 9.307379] 15 00 0 1 0 1 0 0 0 A1 [ 9.307677] 16 00 1 1 0 1 0 0 0 A9 [ 9.307976] 17 00 0 1 0 1 0 0 0 99 [ 9.308272] IRQ to pin mappings: [ 9.308458] IRQ0 -> 0:2 [ 9.308684] IRQ1 -> 0:1 [ 9.308922] IRQ3 -> 0:3 [ 9.309149] IRQ4 -> 0:4 [ 9.309377] IRQ5 -> 0:5 [ 9.309603] IRQ6 -> 0:6 [ 9.309830] IRQ7 -> 0:7 [ 9.310057] IRQ8 -> 0:8 [ 9.310284] IRQ9 -> 0:9 [ 9.310513] IRQ10 -> 0:10 [ 9.310745] IRQ11 -> 0:11 [ 9.310979] IRQ12 -> 0:12 [ 9.311212] IRQ13 -> 0:13 [ 9.311445] IRQ14 -> 0:14 [ 9.311679] IRQ15 -> 0:15 [ 9.311913] IRQ16 -> 0:16 [ 9.312147] IRQ17 -> 0:17 [ 9.312381] IRQ18 -> 0:18 [ 9.312613] IRQ19 -> 0:19 [ 9.312846] IRQ20 -> 0:20 [ 9.313107] IRQ21 -> 0:21 [ 9.313344] IRQ22 -> 0:22 [ 9.313577] IRQ23 -> 0:23 [ 9.313811] .................................... done. [ 9.314756] PM: Hibernation image not present or could not be loaded. [ 9.315095] registered taskstats version 1 [ 9.316530] Magic number: 7:821:84 [ 9.316912] rtc_cmos 00:02: setting system clock to 2011-08-08 16:03:38 UTC (1312819418) [ 9.333110] ehci_hcd 0000:00:1a.7: port 1 high speed [ 9.333400] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.341088] IP-Config: Complete: [ 9.341330] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 9.341971] host=fat, domain=, nis-domain=(none), [ 9.342317] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 9.388864] usb 1-1: new high speed USB device number 2 using ehci_hcd [ 9.445016] ehci_hcd 0000:00:1a.7: port 1 high speed [ 9.445289] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.527862] usb 1-1: default language 0x0409 [ 9.533579] VFS: Mounted root (nfs filesystem) on device 0:16. [ 9.533903] debug: unmapping init memory ffffffff82499000..ffffffff8276d000 [ 9.534901] usb 1-1: udev 2, busnum 1, minor = 1 [ 9.535148] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 9.535474] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9.535815] usb 1-1: Product: AX88178 [ 9.536025] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 9.536408] usb 1-1: SerialNumber: 000013 [ 9.537560] kworker/u:8 used greatest stack depth: 3000 bytes left [ 9.537624] usb 1-1: usb_probe_device [ 9.537628] usb 1-1: configuration #1 chosen from 1 choice [ 9.538389] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 9.539518] asix 1-1:1.0: usb_probe_interface [ 9.539756] asix 1-1:1.0: usb_probe_interface - got id [ 10.261987] usb usb5: suspend_rh (auto-stop) [ 10.262279] usb usb6: suspend_rh (auto-stop) [ 10.262531] usb usb7: suspend_rh (auto-stop) [ 10.262782] usb usb8: suspend_rh (auto-stop) [ 10.297236] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 10.297963] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '002' [ 10.298634] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 10.299012] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 10.353761] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 10.354427] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s [ 10.410025] ehci_hcd 0000:00:1a.7: port 4 high speed [ 10.410298] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 10.465438] usb 1-4: new high speed USB device number 4 using ehci_hcd [ 10.509278] usb usb4: suspend_rh (auto-stop) [ 10.521928] ehci_hcd 0000:00:1a.7: port 4 high speed [ 10.522203] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 11.515507] usb 1-4: default language 0x0409 [ 11.517164] usb 1-4: udev 4, busnum 1, minor = 3 [ 11.517410] usb 1-4: New USB device found, idVendor=1307, idProduct=0165 [ 11.517729] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 11.518180] usb 1-4: Product: USB Mass Storage Device [ 11.518483] usb 1-4: Manufacturer: Teclast Technology [ 11.518781] usb 1-4: SerialNumber: 0000000000020D [ 11.519378] usb 1-4: usb_probe_device [ 11.519592] usb 1-4: configuration #1 chosen from 1 choice [ 11.520016] usb 1-4: adding 1-4:1.0 (config #1, interface 0) [ 11.520401] usb-storage 1-4:1.0: usb_probe_interface [ 11.520662] usb-storage 1-4:1.0: usb_probe_interface - got id [ 11.521298] scsi9 : usb-storage 1-4:1.0 [ 11.521882] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '004' [ 11.522332] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 11.522628] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 11.522931] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 11.653937] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 11.769446] usb 3-2: new low speed USB device number 2 using uhci_hcd [ 11.985624] usb 3-2: skipped 1 descriptor after interface [ 11.985937] usb 3-2: skipped 1 descriptor after interface [ 11.992815] usb 3-2: default language 0x0409 [ 12.023523] usb 3-2: udev 2, busnum 3, minor = 257 [ 12.023805] usb 3-2: New USB device found, idVendor=0557, idProduct=2220 [ 12.024147] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.024611] usb 3-2: Product: ATEN CS-1758/54 [ 12.024880] usb 3-2: Manufacturer: ATEN [ 12.025687] usb 3-2: usb_probe_device [ 12.025923] usb 3-2: configuration #1 chosen from 1 choice [ 12.028786] usb 3-2: adding 3-2:1.0 (config #1, interface 0) [ 12.069704] usbhid 3-2:1.0: usb_probe_interface [ 12.069986] usbhid 3-2:1.0: usb_probe_interface - got id [ 12.103466] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input4 [ 12.104210] uhci_hcd 0000:00:1a.0: reserve dev 2 ep81-INT, period 8, phase 4, 118 us [ 12.105271] generic-usb 0003:0557:2220.0001: input: USB HID v1.10 Keyboard [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input0 [ 12.106034] usb 3-2: adding 3-2:1.1 (config #1, interface 1) [ 12.114564] usbhid 3-2:1.1: usb_probe_interface [ 12.114847] usbhid 3-2:1.1: usb_probe_interface - got id [ 12.144037] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.1/input/input5 [ 12.145446] generic-usb 0003:0557:2220.0002: input: USB HID v1.10 Mouse [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input1 [ 12.146138] /c/wfg/sound-2.6/drivers/usb/core/inode.c: creating file '002' [ 12.146677] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.146992] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 12.517192] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 12.697228] EXT4-fs (sda5): recovery complete [ 12.697729] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 12.965448] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 12.966944] sd 9:0:0:0: [sdb] Write Protect is off [ 12.967224] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 12.968451] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.968759] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 12.975508] sd 9:0:0:0: [sdb] Asking for cache data failed [ 12.975818] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 13.109805] sdb: sdb1 sdb2 sdb3 [ 13.116298] sd 9:0:0:0: [sdb] Asking for cache data failed [ 13.116593] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 13.116911] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 13.845397] svc: failed to register lockdv1 RPC service (errno 97). [ 19.736644] eth0: no IPv6 routers present [ 47.689857] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)