[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.0-next-20110802+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #574 SMP Tue Aug 16 15:26:46 CST 2011 [ 0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.0.0-next-20110802+ [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcda4000 (usable) [ 0.000000] BIOS-e820: 00000000bcda4000 - 00000000bcfdd000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcfdd000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf800000 [ 0.000000] 0000000000 - 00bf800000 page 4k [ 0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000 [ 0.000000] log_buf_len: 8388608 [ 0.000000] early log buf free: 258248(98%) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-00000000bf800000 [ 0.000000] Initmem setup node 0 0000000000000000-00000000bf800000 [ 0.000000] NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff] [ 0.000000] [ffffea0000000000-ffffea0002ffffff] PMD -> [ffff8800b9c00000-ffff8800bcbfffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x000bcda4 [ 0.000000] 0: 0x000bcfdd -> 0x000bf6bd [ 0.000000] 0: 0x000bf6bf -> 0x000bf714 [ 0.000000] 0: 0x000bf7bf -> 0x000bf7e7 [ 0.000000] 0: 0x000bf7ff -> 0x000bf800 [ 0.000000] On node 0 totalpages: 783502 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3911 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 12192 pages used for memmap [ 0.000000] DMA32 zone: 767330 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bcda4000 - 00000000bcfdd000 [ 0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915520 r8192 d21888 u2097152 [ 0.000000] pcpu-alloc: s1915520 r8192 d21888 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 771241 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.0.0-next-20110802+ [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Memory: 3012660k/3137536k available (9616k kernel code, 3528k absent, 121348k reserved, 5708k data, 2752k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] NR_IRQS:4352 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6335 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 25165824 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.001000] Fast TSC calibration using PIT [ 0.002000] Detected 3200.133 MHz processor. [ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6400.26 BogoMIPS (lpj=3200133) [ 0.000707] pid_max: default: 32768 minimum: 301 [ 0.001882] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003944] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.004944] Mount-cache hash table entries: 256 [ 0.005641] Initializing cgroup subsys debug [ 0.005950] Initializing cgroup subsys cpuacct [ 0.006282] Initializing cgroup subsys memory [ 0.006618] Initializing cgroup subsys devices [ 0.006933] Initializing cgroup subsys freezer [ 0.007257] Initializing cgroup subsys blkio [ 0.007619] CPU: Physical Processor ID: 0 [ 0.007916] CPU: Processor Core ID: 0 [ 0.008214] mce: CPU supports 9 MCE banks [ 0.008519] CPU0: Thermal monitoring enabled (TM1) [ 0.008856] using mwait in idle threads. [ 0.010006] ACPI: Core revision 20110623 [ 0.021650] ftrace: allocating 36661 entries in 144 pages [ 0.030374] Getting VERSION: 60015 [ 0.030650] Getting VERSION: 60015 [ 0.030923] Getting ID: 0 [ 0.031179] Getting ID: 0 [ 0.031424] Switched APIC routing to physical flat. [ 0.031755] enabled ExtINT on CPU#0 [ 0.032198] ENABLING IO-APIC IRQs [ 0.032469] init IO_APIC IRQs [ 0.032728] apic 8 pin 0 not connected [ 0.033026] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0) [ 0.033600] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0) [ 0.034171] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) [ 0.034735] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0) [ 0.035301] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0) [ 0.035863] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0) [ 0.036428] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0) [ 0.036991] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 0.037558] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0) [ 0.038124] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0) [ 0.038693] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0) [ 0.039265] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0) [ 0.039832] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 0.040403] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0) [ 0.040970] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0) [ 0.041539] apic 8 pin 16 not connected [ 0.041832] apic 8 pin 17 not connected [ 0.042129] apic 8 pin 18 not connected [ 0.042422] apic 8 pin 19 not connected [ 0.042715] apic 8 pin 20 not connected [ 0.043009] apic 8 pin 21 not connected [ 0.043305] apic 8 pin 22 not connected [ 0.043598] apic 8 pin 23 not connected [ 0.044026] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.054368] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.054849] Using local APIC timer interrupts. [ 0.054849] calibrating APIC timer ... [ 0.156671] ... lapic delta = 833239 [ 0.156952] ... PM-Timer delta = 357902 [ 0.157242] ... PM-Timer result ok [ 0.157516] ..... delta 833239 [ 0.157777] ..... mult: 35792783 [ 0.158045] ..... calibration result: 133318 [ 0.158351] ..... CPU clock speed is 3199.0643 MHz. [ 0.158680] ..... host bus clock speed is 133.0318 MHz. [ 0.159033] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver. [ 0.159792] ... version: 3 [ 0.160093] ... bit width: 48 [ 0.160394] ... generic registers: 4 [ 0.160692] ... value mask: 0000ffffffffffff [ 0.161039] ... max period: 000000007fffffff [ 0.161385] ... fixed-purpose events: 3 [ 0.161683] ... event mask: 000000070000000f [ 0.162313] lockdep: fixing up alternatives. [ 0.162676] Booting Node 0, Processors #1 [ 0.162894] smpboot cpu 1: start_ip = 97000 [ 0.174433] masked ExtINT on CPU#1 [ 0.253976] lockdep: fixing up alternatives. [ 0.254307] #2 [ 0.254399] smpboot cpu 2: start_ip = 97000 [ 0.265935] masked ExtINT on CPU#2 [ 0.345616] lockdep: fixing up alternatives. [ 0.345948] #3 [ 0.346040] smpboot cpu 3: start_ip = 97000 [ 0.357577] masked ExtINT on CPU#3 [ 0.437261] lockdep: fixing up alternatives. [ 0.437597] #4 [ 0.437689] smpboot cpu 4: start_ip = 97000 [ 0.449225] masked ExtINT on CPU#4 [ 0.528962] lockdep: fixing up alternatives. [ 0.529294] #5 [ 0.529387] smpboot cpu 5: start_ip = 97000 [ 0.543883] masked ExtINT on CPU#5 [ 0.623683] lockdep: fixing up alternatives. [ 0.624017] #6 [ 0.624109] smpboot cpu 6: start_ip = 97000 [ 0.635230] masked ExtINT on CPU#6 [ 0.714322] lockdep: fixing up alternatives. [ 0.714654] #7 [ 0.714746] smpboot cpu 7: start_ip = 97000 [ 0.726281] masked ExtINT on CPU#7 [ 0.805978] Brought up 8 CPUs [ 0.806239] Total of 8 processors activated (51187.97 BogoMIPS). [ 0.809929] CPU0 attaching sched-domain: [ 0.810226] domain 0: span 0,4 level SIBLING [ 0.810570] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 0.811103] domain 1: span 0-7 level MC [ 0.811434] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.812388] CPU1 attaching sched-domain: [ 0.812682] domain 0: span 1,5 level SIBLING [ 0.813027] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 0.813555] domain 1: span 0-7 level MC [ 0.813889] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.814840] CPU2 attaching sched-domain: [ 0.815134] domain 0: span 2,6 level SIBLING [ 0.815477] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 0.816009] domain 1: span 0-7 level MC [ 0.816338] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.817291] CPU3 attaching sched-domain: [ 0.817584] domain 0: span 3,7 level SIBLING [ 0.817931] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 0.818459] domain 1: span 0-7 level MC [ 0.818791] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.819741] CPU4 attaching sched-domain: [ 0.820038] domain 0: span 0,4 level SIBLING [ 0.820380] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 0.820911] domain 1: span 0-7 level MC [ 0.821241] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.822194] CPU5 attaching sched-domain: [ 0.822488] domain 0: span 1,5 level SIBLING [ 0.822832] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 0.823361] domain 1: span 0-7 level MC [ 0.823691] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.824643] CPU6 attaching sched-domain: [ 0.824940] domain 0: span 2,6 level SIBLING [ 0.825283] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 0.825814] domain 1: span 0-7 level MC [ 0.826144] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.827096] CPU7 attaching sched-domain: [ 0.827389] domain 0: span 3,7 level SIBLING [ 0.827732] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 0.828263] domain 1: span 0-7 level MC [ 0.828594] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.829987] devtmpfs: initialized [ 0.830421] kworker/u:0 used greatest stack depth: 5608 bytes left [ 0.830802] kworker/u:0 used greatest stack depth: 5192 bytes left [ 0.832552] PM: Registering ACPI NVS region at bcda4000 (2330624 bytes) [ 0.833017] PM: Registering ACPI NVS region at bf714000 (700416 bytes) [ 0.834079] xor: automatically using best checksumming function: generic_sse [ 0.838714] generic_sse: 11928.000 MB/sec [ 0.839023] xor: using function: generic_sse (11928.000 MB/sec) [ 0.839467] RTC time: 22:45:49, date: 08/16/11 [ 0.839878] NET: Registered protocol family 16 [ 0.840845] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.841393] ACPI: bus type pci registered [ 0.841885] dca service started, version 1.12.1 [ 0.842278] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.842893] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 0.855798] PCI: Using configuration type 1 for base access [ 0.878235] bio: create slab at 0 [ 0.895527] raid6: int64x1 3167 MB/s [ 0.912470] raid6: int64x2 3273 MB/s [ 0.929415] raid6: int64x4 2738 MB/s [ 0.946350] raid6: int64x8 2089 MB/s [ 0.963296] raid6: sse2x1 7921 MB/s [ 0.980234] raid6: sse2x2 9281 MB/s [ 0.997175] raid6: sse2x4 10703 MB/s [ 0.997464] raid6: using algorithm sse2x4 (10703 MB/s) [ 0.997883] ACPI: Added _OSI(Module Device) [ 0.998193] ACPI: Added _OSI(Processor Device) [ 0.998508] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.998831] ACPI: Added _OSI(Processor Aggregator Device) [ 1.003113] ACPI: EC: Look up EC in DSDT [ 1.024103] ACPI: Interpreter enabled [ 1.024390] ACPI: (supports S0 S1 S3 S4 S5) [ 1.024896] ACPI: Using IOAPIC for interrupt routing [ 1.037340] ACPI: No dock devices found. [ 1.037637] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.038848] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 1.040460] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 1.040854] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 1.041251] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.041786] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 1.042323] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 1.042858] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 1.043419] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 1.043856] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 1.044288] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.044664] pci 0000:00:01.0: PME# disabled [ 1.044992] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 1.045419] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 1.045796] pci 0000:00:03.0: PME# disabled [ 1.046129] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 1.046552] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 1.046929] pci 0000:00:07.0: PME# disabled [ 1.047265] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 1.047708] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 1.048161] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 1.048602] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 1.049047] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 1.049487] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 1.049933] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 1.050325] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 1.050708] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 1.051094] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 1.051501] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.051878] pci 0000:00:19.0: PME# disabled [ 1.052207] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 1.052627] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 1.053033] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 1.053453] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 1.053854] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 1.054278] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 1.054688] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 1.055080] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 1.055537] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 1.055913] pci 0000:00:1a.7: PME# disabled [ 1.056245] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 1.056629] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 1.057094] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.057470] pci 0000:00:1b.0: PME# disabled [ 1.057793] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 1.058233] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.058608] pci 0000:00:1c.0: PME# disabled [ 1.058933] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 1.059373] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.059749] pci 0000:00:1c.1: PME# disabled [ 1.060081] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 1.060517] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.060893] pci 0000:00:1c.4: PME# disabled [ 1.061227] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 1.061646] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 1.062050] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 1.062469] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 1.062871] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 1.063296] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 1.063711] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 1.064104] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 1.064562] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 1.064943] pci 0000:00:1d.7: PME# disabled [ 1.065267] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 1.065706] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 1.066175] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 1.066556] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 1.067108] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 1.067698] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 1.068090] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 1.068446] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 1.068801] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 1.069160] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 1.069517] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 1.069872] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 1.070288] pci 0000:00:1f.2: PME# supported from D3hot [ 1.070633] pci 0000:00:1f.2: PME# disabled [ 1.070960] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 1.071346] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 1.071764] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 1.072190] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.075564] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 1.075944] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 1.076326] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 1.076753] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 1.077168] pci 0000:02:00.0: supports D1 D2 [ 1.077496] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 1.077874] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 1.078317] pci 0000:02:00.1: supports D1 D2 [ 1.078641] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.078989] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.079393] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.079990] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.080389] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.080789] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.081217] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 1.081606] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 1.081974] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 1.082338] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 1.082700] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 1.083066] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 1.083429] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 1.083866] pci 0000:06:00.0: supports D1 [ 1.084167] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 1.084532] pci 0000:06:00.0: PME# disabled [ 1.084856] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.085204] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.085580] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.086029] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 1.086416] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 1.086800] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 1.087250] pci 0000:07:03.0: supports D1 D2 [ 1.087557] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 1.087941] pci 0000:07:03.0: PME# disabled [ 1.088298] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 1.088711] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.089119] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.089676] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.090236] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.090818] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 1.091403] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 1.091989] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 1.092607] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.093892] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 1.094513] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 1.094984] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 1.095449] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 1.095919] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 1.096383] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 1.096864] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 1.097423] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19) [ 1.119999] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.121078] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.122153] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.123230] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.124306] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.125385] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.126459] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.127533] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.128837] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.129407] vgaarb: loaded [ 1.129657] vgaarb: bridge control possible 0000:02:00.0 [ 1.130213] SCSI subsystem initialized [ 1.130665] libata version 3.00 loaded. [ 1.131214] usbcore: registered new interface driver usbfs [ 1.131623] usbcore: registered new interface driver hub [ 1.132045] usbcore: registered new device driver usb [ 1.132812] wmi: Mapper loaded [ 1.133139] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 1.133523] PCI: Using ACPI for IRQ routing [ 1.135402] PCI: Discovered peer bus 3f [ 1.135770] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600 [ 1.136168] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600 [ 1.136572] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600 [ 1.136975] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600 [ 1.137374] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600 [ 1.137774] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600 [ 1.138171] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600 [ 1.138568] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600 [ 1.138967] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600 [ 1.139362] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600 [ 1.139759] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600 [ 1.140158] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600 [ 1.140552] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600 [ 1.140951] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600 [ 1.141346] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600 [ 1.141751] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600 [ 1.142148] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600 [ 1.142542] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600 [ 1.142944] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600 [ 1.144677] PCI: pci_cache_line_size set to 64 bytes [ 1.145243] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 1.145505] reserve RAM buffer: 00000000bcda4000 - 00000000bfffffff [ 1.145929] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff [ 1.146347] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff [ 1.146768] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff [ 1.147185] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff [ 1.173099] pnp: PnP ACPI init [ 1.173538] ACPI: bus type pnp registered [ 1.174450] pnp 00:00: [bus 00-3d] [ 1.174732] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.175033] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.175357] pnp 00:00: [io 0x0d00-0xffff window] [ 1.175684] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.176034] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 1.176383] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 1.176739] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 1.177088] pnp 00:00: [mem 0x00000000 window] [ 1.177538] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 1.178211] pnp 00:01: [io 0x0000-0x000f] [ 1.178513] pnp 00:01: [io 0x0081-0x0083] [ 1.178818] pnp 00:01: [io 0x0087] [ 1.179098] pnp 00:01: [io 0x0089-0x008b] [ 1.179398] pnp 00:01: [io 0x008f] [ 1.179679] pnp 00:01: [io 0x00c0-0x00df] [ 1.179979] pnp 00:01: [dma 4] [ 1.180331] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.180744] pnp 00:02: [io 0x0070-0x0071] [ 1.181045] pnp 00:02: [io 0x0074-0x0077] [ 1.181350] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 1.181916] pnp 00:02: [irq 8] [ 1.182268] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.182684] pnp 00:03: [io 0x00f0] [ 1.182966] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 1.183532] pnp 00:03: [irq 13] [ 1.183892] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.184301] pnp 00:04: [io 0x0061] [ 1.184677] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.185085] pnp 00:05: [io 0x0500-0x053f] [ 1.185385] pnp 00:05: [io 0x0400-0x047f] [ 1.185690] pnp 00:05: [io 0x0092] [ 1.185967] pnp 00:05: [io 0x0680-0x06ff] [ 1.186267] pnp 00:05: [io 0x0010-0x001f] [ 1.186570] pnp 00:05: [io 0x0072-0x0073] [ 1.186871] pnp 00:05: [io 0x0080] [ 1.187149] pnp 00:05: [io 0x0084-0x0086] [ 1.187448] pnp 00:05: [io 0x0088] [ 1.187731] pnp 00:05: [io 0x008c-0x008e] [ 1.188031] pnp 00:05: [io 0x0090-0x009f] [ 1.188509] system 00:05: [io 0x0500-0x053f] has been reserved [ 1.188887] system 00:05: [io 0x0400-0x047f] has been reserved [ 1.189256] system 00:05: [io 0x0680-0x06ff] has been reserved [ 1.189630] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.190109] pnp 00:06: [io 0x0060] [ 1.190389] pnp 00:06: [io 0x0064] [ 1.190831] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.191775] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 1.192208] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 1.192735] pnp: PnP ACPI: found 8 devices [ 1.193037] ACPI: ACPI bus type pnp unregistered [ 1.203920] Switching to clocksource acpi_pm [ 1.204357] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 1.204542] Switched to NOHz mode on CPU #3 [ 1.204544] Switched to NOHz mode on CPU #6 [ 1.204552] Switched to NOHz mode on CPU #4 [ 1.204574] Switched to NOHz mode on CPU #2 [ 1.204589] Switched to NOHz mode on CPU #5 [ 1.204610] Switched to NOHz mode on CPU #7 [ 1.204613] Switched to NOHz mode on CPU #1 [ 1.207092] Switched to NOHz mode on CPU #0 [ 1.207441] PCI: max bus depth: 1 pci_try_num: 2 [ 1.210787] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.211140] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 1.211678] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.212022] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.212432] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.212986] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.213336] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.213693] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.214045] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.214398] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.214775] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.215181] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 1.215956] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.216386] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0) [ 1.216952] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.217361] pci 0000:00:01.0: setting latency timer to 64 [ 1.217715] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.218113] pci 0000:00:03.0: setting latency timer to 64 [ 1.218476] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.218876] pci 0000:00:07.0: setting latency timer to 64 [ 1.219234] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0) [ 1.219806] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.220205] pci 0000:00:1c.0: setting latency timer to 64 [ 1.220565] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 1.220965] pci 0000:00:1c.1: setting latency timer to 64 [ 1.221318] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.221722] pci 0000:00:1c.4: setting latency timer to 64 [ 1.222076] pci 0000:00:1e.0: setting latency timer to 64 [ 1.222435] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.222790] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.223144] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.223534] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.223914] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.224293] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.224679] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 1.225059] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.225598] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 1.225952] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 1.226342] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 1.226722] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 1.227076] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 1.227441] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 1.227820] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.228200] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.228586] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.228966] pci_bus 0000:3f: resource 0 [io 0x0000-0xffff] [ 1.229330] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff] [ 1.229772] NET: Registered protocol family 2 [ 1.230408] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.232805] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.236517] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) [ 1.239414] TCP: Hash tables configured (established 524288 bind 65536) [ 1.239825] TCP reno registered [ 1.240155] UDP hash table entries: 2048 (order: 6, 393216 bytes) [ 1.240761] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes) [ 1.241476] NET: Registered protocol family 1 [ 1.241995] RPC: Registered named UNIX socket transport module. [ 1.242378] RPC: Registered udp transport module. [ 1.242703] RPC: Registered tcp transport module. [ 1.243026] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.243463] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.243853] pci 0000:00:1a.0: Performing full reset [ 1.244199] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.244598] pci 0000:00:1a.1: Performing full reset [ 1.244944] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.245341] pci 0000:00:1a.2: Performing full reset [ 1.245838] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.246229] pci 0000:00:1d.0: Performing full reset [ 1.246600] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.246991] pci 0000:00:1d.1: Performing full reset [ 1.247345] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.247734] pci 0000:00:1d.2: Performing full reset [ 1.248222] pci 0000:02:00.0: Boot video device [ 1.248604] PCI: CLS 64 bytes, default 64 [ 1.252705] Machine check injector initialized [ 1.254863] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 1.255240] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 1.255612] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 1.255981] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 1.256356] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 1.256730] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 1.257098] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 1.257467] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 1.257925] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 1.259030] audit: initializing netlink socket (disabled) [ 1.259417] type=2000 audit(1313534749.013:1): initialized [ 1.291355] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.303579] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.304533] fuse init (API version 7.16) [ 1.305443] JFS: nTxBlock = 8192, nTxLock = 65536 [ 1.308933] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.311608] NILFS version 2 loaded [ 1.312926] Btrfs loaded [ 1.313189] msgmni has been set to 5884 [ 1.314627] async_tx: api initialized (async) [ 1.315181] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.315772] io scheduler noop registered [ 1.316096] io scheduler deadline registered [ 1.316551] io scheduler cfq registered (default) [ 1.317312] pcieport 0000:00:1c.0: setting latency timer to 64 [ 1.317730] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 1.318228] pcieport 0000:00:1c.1: setting latency timer to 64 [ 1.318642] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 1.319208] pcieport 0000:00:1c.4: setting latency timer to 64 [ 1.319622] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 1.320332] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.321140] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 1.321720] ACPI: Sleep Button [SLPB] [ 1.322155] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.322698] ACPI: Power Button [PWRF] [ 1.323709] ACPI: acpi_idle registered with cpuidle [ 1.324460] Monitor-Mwait will be used to enter C-1 state [ 1.324859] Monitor-Mwait will be used to enter C-3 state [ 1.332297] ioatdma: Intel(R) QuickData Technology Driver 4.00 [ 1.384399] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.404875] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 1.453908] Initializing Nozomi driver 2.1d [ 1.454746] Non-volatile memory driver v1.3 [ 1.455483] Linux agpgart interface v0.103 [ 1.455879] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 1.456475] Hangcheck: Using getrawmonotonic(). [ 1.456865] [drm] Initialized drm 1.1.0 20060810 [ 1.457185] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 2.248243] Refined TSC clocksource calibration: 3200.113 MHz. [ 2.248610] Switching to clocksource tsc [ 4.467370] floppy0: no floppy controllers found [ 4.598892] brd: module loaded [ 4.600798] loop: module loaded [ 4.601539] Loading iSCSI transport class v2.0-870. [ 4.602459] Loading Adaptec I2O RAID: Version 2.4 Build 5go [ 4.602814] Detecting Adaptec I2O RAID controllers... [ 4.603327] Adaptec aacraid driver 1.1-7[28000]-ms [ 4.604203] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 4.604785] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.03-k. [ 4.605512] iscsi: registered transport (qla4xxx) [ 4.605914] QLogic iSCSI HBA Driver [ 4.606273] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) [ 4.606898] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) [ 4.607379] megasas: 00.00.05.40-rc1 Tue. Jul. 26 17:00:00 PDT 2011 [ 4.607844] mpt2sas version 09.100.00.00 loaded [ 4.608539] ahci 0000:00:1f.2: version 3.0 [ 4.608875] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0) [ 4.609444] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.609893] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 4.610299] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 4.610871] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 4.611430] ahci 0000:00:1f.2: setting latency timer to 64 [ 4.623053] scsi0 : ahci [ 4.623495] scsi1 : ahci [ 4.623898] scsi2 : ahci [ 4.624301] scsi3 : ahci [ 4.624691] scsi4 : ahci [ 4.625090] scsi5 : ahci [ 4.625726] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43 [ 4.626271] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43 [ 4.626814] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 4.627352] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 4.630862] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 4.631401] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 4.631970] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.632384] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 4.633045] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 4.633451] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 4.633860] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 4.634228] ahci: SSS flag set, parallel bus scan disabled [ 4.634619] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 4.635182] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 4.635554] ahci 0000:06:00.0: setting latency timer to 64 [ 4.636708] scsi6 : ahci [ 4.637115] scsi7 : ahci [ 4.637511] scsi8 : ahci [ 4.637896] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 4.638436] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 4.638976] ata9: DUMMY [ 4.641196] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 4.641606] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 4.642047] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k [ 4.642415] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 4.642814] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0) [ 4.643381] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 4.643796] e1000e 0000:00:19.0: setting latency timer to 64 [ 4.644264] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 4.834659] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54 [ 4.835227] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.835663] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 4.836141] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k [ 4.836531] Copyright (c) 2007-2011 Intel Corporation. [ 4.836945] Intel(R) Virtual Function Network Driver - version 2.0.0-k [ 4.837339] Copyright (c) 2009 - 2010 Intel Corporation. [ 4.837756] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k [ 4.838305] ixgbe: Copyright (c) 1999-2011 Intel Corporation. [ 4.838740] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 4.839154] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 4.839865] jme: JMicron JMC2XX ethernet driver version 1.0.8 [ 4.840512] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 4.841128] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011) [ 4.841777] sky2: driver version 1.29 [ 4.843021] tun: Universal TUN/TAP device driver, 1.6 [ 4.843362] tun: (C) 1999-2004 Max Krasnyansky [ 4.844035] usbcore: registered new interface driver catc [ 4.844390] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 4.844806] usbcore: registered new interface driver kaweth [ 4.845164] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 4.845751] usbcore: registered new interface driver pegasus [ 4.846114] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 4.846573] usbcore: registered new interface driver rtl8150 [ 4.846982] usbcore: registered new interface driver asix [ 4.847385] usbcore: registered new interface driver cdc_ether [ 4.847795] usbcore: registered new interface driver cdc_eem [ 4.848203] usbcore: registered new interface driver dm9601 [ 4.848619] usbcore: registered new interface driver smsc75xx [ 4.849034] usbcore: registered new interface driver smsc95xx [ 4.849446] usbcore: registered new interface driver gl620a [ 4.849849] usbcore: registered new interface driver net1080 [ 4.850257] usbcore: registered new interface driver plusb [ 4.850658] usbcore: registered new interface driver rndis_host [ 4.851074] usbcore: registered new interface driver cdc_subset [ 4.851494] usbcore: registered new interface driver zaurus [ 4.851896] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 4.852494] usbcore: registered new interface driver int51x1 [ 4.852851] cdc_ncm: 01-June-2011 [ 4.853177] usbcore: registered new interface driver cdc_ncm [ 4.853537] netconsole: local port 6665 [ 4.853828] netconsole: local IP 10.0.0.0 [ 4.854128] netconsole: interface 'eth0' [ 4.854422] netconsole: remote port 6666 [ 4.854716] netconsole: remote IP 192.168.1.1 [ 4.855027] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 4.855405] netconsole: device eth0 not up yet, forcing it [ 4.935861] ata4: SATA link down (SStatus 0 SControl 300) [ 4.936232] ata5: SATA link down (SStatus 0 SControl 300) [ 4.936603] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.937017] ata6: SATA link down (SStatus 0 SControl 300) [ 4.937387] ata3: SATA link down (SStatus 0 SControl 300) [ 4.942848] ata7: SATA link down (SStatus 0 SControl 300) [ 4.949019] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 4.979850] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 4.980209] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.999710] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.037971] ata1.00: configured for UDMA/133 [ 5.038456] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 5.039327] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 5.039956] sd 0:0:0:0: [sda] Write Protect is off [ 5.040283] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.040652] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.129717] sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 > [ 5.131077] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.292844] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 5.365453] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 5.365848] ata2.00: applying bridge limits [ 5.396619] ata2.00: configured for UDMA/33 [ 5.397930] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 5.702502] ata8: SATA link down (SStatus 0 SControl 300) [ 7.748012] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 7.750426] console [netcon0] enabled [ 7.750715] netconsole: network logging started [ 7.751099] Fusion MPT base driver 3.04.19 [ 7.751407] Copyright (c) 1999-2008 LSI Corporation [ 7.751748] Fusion MPT SPI Host driver 3.04.19 [ 7.752149] Fusion MPT FC Host driver 3.04.19 [ 7.752541] Fusion MPT SAS Host driver 3.04.19 [ 7.752936] Fusion MPT misc device (ioctl) driver 3.04.19 [ 7.753381] mptctl: Registered with Fusion MPT base driver [ 7.753735] mptctl: /dev/mptctl @ (major,minor=10,220) [ 7.754190] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.754583] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 7.754994] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0) [ 7.755568] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 7.755995] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 7.756367] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 7.756772] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file 'devices' [ 7.757328] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.757749] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 7.758300] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 7.758899] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 7.759552] ehci_hcd 0000:00:1a.7: debug port 1 [ 7.759874] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.764354] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 7.764756] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 7.765141] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 7.765504] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.769978] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 7.776045] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 7.776495] usb usb1: default language 0x0409 [ 7.776817] usb usb1: udev 1, busnum 1, minor = 0 [ 7.777147] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.777550] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.778089] usb usb1: Product: EHCI Host Controller [ 7.778421] usb usb1: Manufacturer: Linux 3.0.0-next-20110802+ ehci_hcd [ 7.778817] usb usb1: SerialNumber: 0000:00:1a.7 [ 7.779297] usb usb1: usb_probe_device [ 7.779590] usb usb1: configuration #1 chosen from 1 choice [ 7.779972] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 7.780421] hub 1-0:1.0: usb_probe_interface [ 7.780733] hub 1-0:1.0: usb_probe_interface - got id [ 7.781075] hub 1-0:1.0: USB hub found [ 7.781370] hub 1-0:1.0: 6 ports detected [ 7.781670] hub 1-0:1.0: standalone hub [ 7.781963] hub 1-0:1.0: no power switching (usb 1.0) [ 7.782303] hub 1-0:1.0: individual port over-current protection [ 7.782676] hub 1-0:1.0: power on to power good time: 20ms [ 7.783049] hub 1-0:1.0: local power source is good [ 7.783381] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 7.783830] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.784361] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0) [ 7.784932] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 7.785363] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 7.785732] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 7.786085] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '002' [ 7.786498] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 7.790013] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 7.790613] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 7.791252] ehci_hcd 0000:00:1d.7: debug port 1 [ 7.791573] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.796055] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 7.796456] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 7.796838] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 7.797205] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.801679] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 7.807946] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 7.808347] usb usb2: default language 0x0409 [ 7.808667] usb usb2: udev 1, busnum 2, minor = 128 [ 7.809003] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.809404] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.809940] usb usb2: Product: EHCI Host Controller [ 7.810272] usb usb2: Manufacturer: Linux 3.0.0-next-20110802+ ehci_hcd [ 7.810666] usb usb2: SerialNumber: 0000:00:1d.7 [ 7.811127] usb usb2: usb_probe_device [ 7.811418] usb usb2: configuration #1 chosen from 1 choice [ 7.811782] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 7.812213] hub 2-0:1.0: usb_probe_interface [ 7.812523] hub 2-0:1.0: usb_probe_interface - got id [ 7.812860] hub 2-0:1.0: USB hub found [ 7.813157] hub 2-0:1.0: 6 ports detected [ 7.813457] hub 2-0:1.0: standalone hub [ 7.813749] hub 2-0:1.0: no power switching (usb 1.0) [ 7.814089] hub 2-0:1.0: individual port over-current protection [ 7.814462] hub 2-0:1.0: power on to power good time: 20ms [ 7.814820] hub 2-0:1.0: local power source is good [ 7.815154] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 7.815601] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.816157] uhci_hcd: USB Universal Host Controller Interface driver [ 7.816589] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 7.817015] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 7.817383] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 7.817733] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '003' [ 7.818148] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 7.818695] uhci_hcd 0000:00:1a.0: detected 2 ports [ 7.819032] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.819430] uhci_hcd 0000:00:1a.0: Performing full reset [ 7.819788] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 7.820158] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 7.820572] usb usb3: default language 0x0409 [ 7.820898] usb usb3: udev 1, busnum 3, minor = 256 [ 7.821230] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.821632] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.822172] usb usb3: Product: UHCI Host Controller [ 7.822504] usb usb3: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.822903] usb usb3: SerialNumber: 0000:00:1a.0 [ 7.823363] usb usb3: usb_probe_device [ 7.823655] usb usb3: configuration #1 chosen from 1 choice [ 7.824024] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 7.824449] hub 3-0:1.0: usb_probe_interface [ 7.824759] hub 3-0:1.0: usb_probe_interface - got id [ 7.825099] hub 3-0:1.0: USB hub found [ 7.825392] hub 3-0:1.0: 2 ports detected [ 7.825691] hub 3-0:1.0: standalone hub [ 7.825986] hub 3-0:1.0: no power switching (usb 1.0) [ 7.826325] hub 3-0:1.0: individual port over-current protection [ 7.826700] hub 3-0:1.0: power on to power good time: 2ms [ 7.827060] hub 3-0:1.0: local power source is good [ 7.827391] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 7.827818] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.828280] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 7.828713] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0) [ 7.829288] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 7.829707] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 7.830078] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 7.830428] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '004' [ 7.830841] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 7.831390] uhci_hcd 0000:00:1a.1: detected 2 ports [ 7.831724] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.832125] uhci_hcd 0000:00:1a.1: Performing full reset [ 7.832484] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 7.832869] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 7.833269] usb usb4: default language 0x0409 [ 7.833589] usb usb4: udev 1, busnum 4, minor = 384 [ 7.833926] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.834327] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.834864] usb usb4: Product: UHCI Host Controller [ 7.835196] usb usb4: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.835590] usb usb4: SerialNumber: 0000:00:1a.1 [ 7.836051] usb usb4: usb_probe_device [ 7.836343] usb usb4: configuration #1 chosen from 1 choice [ 7.836705] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 7.837136] hub 4-0:1.0: usb_probe_interface [ 7.837445] hub 4-0:1.0: usb_probe_interface - got id [ 7.837782] hub 4-0:1.0: USB hub found [ 7.838080] hub 4-0:1.0: 2 ports detected [ 7.838380] hub 4-0:1.0: standalone hub [ 7.838672] hub 4-0:1.0: no power switching (usb 1.0) [ 7.839012] hub 4-0:1.0: individual port over-current protection [ 7.839384] hub 4-0:1.0: power on to power good time: 2ms [ 7.839739] hub 4-0:1.0: local power source is good [ 7.840073] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 7.840498] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.840960] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 7.841388] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 7.841808] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 7.842181] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 7.842531] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '005' [ 7.842947] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 7.843493] uhci_hcd 0000:00:1a.2: detected 2 ports [ 7.843831] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.844229] uhci_hcd 0000:00:1a.2: Performing full reset [ 7.844590] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 7.844974] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 7.845378] usb usb5: default language 0x0409 [ 7.845700] usb usb5: udev 1, busnum 5, minor = 512 [ 7.846036] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.846438] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.846976] usb usb5: Product: UHCI Host Controller [ 7.847308] usb usb5: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.847703] usb usb5: SerialNumber: 0000:00:1a.2 [ 7.848162] usb usb5: usb_probe_device [ 7.848453] usb usb5: configuration #1 chosen from 1 choice [ 7.848820] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 7.849247] hub 5-0:1.0: usb_probe_interface [ 7.849558] hub 5-0:1.0: usb_probe_interface - got id [ 7.849899] hub 5-0:1.0: USB hub found [ 7.850192] hub 5-0:1.0: 2 ports detected [ 7.850490] hub 5-0:1.0: standalone hub [ 7.850783] hub 5-0:1.0: no power switching (usb 1.0) [ 7.851123] hub 5-0:1.0: individual port over-current protection [ 7.851496] hub 5-0:1.0: power on to power good time: 2ms [ 7.851854] hub 5-0:1.0: local power source is good [ 7.852186] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 7.852612] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.853079] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 7.853507] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 7.853931] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 7.854298] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 7.854648] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '006' [ 7.855064] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 7.855612] uhci_hcd 0000:00:1d.0: detected 2 ports [ 7.855950] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.856348] uhci_hcd 0000:00:1d.0: Performing full reset [ 7.856707] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 7.857078] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 7.857478] usb usb6: default language 0x0409 [ 7.857803] usb usb6: udev 1, busnum 6, minor = 640 [ 7.858136] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.858539] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.859077] usb usb6: Product: UHCI Host Controller [ 7.859409] usb usb6: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.859807] usb usb6: SerialNumber: 0000:00:1d.0 [ 7.860269] usb usb6: usb_probe_device [ 7.860561] usb usb6: configuration #1 chosen from 1 choice [ 7.860929] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 7.861357] hub 6-0:1.0: usb_probe_interface [ 7.861667] hub 6-0:1.0: usb_probe_interface - got id [ 7.862009] hub 6-0:1.0: USB hub found [ 7.862303] hub 6-0:1.0: 2 ports detected [ 7.862602] hub 6-0:1.0: standalone hub [ 7.862899] hub 6-0:1.0: no power switching (usb 1.0) [ 7.863237] hub 6-0:1.0: individual port over-current protection [ 7.863610] hub 6-0:1.0: power on to power good time: 2ms [ 7.863970] hub 6-0:1.0: local power source is good [ 7.864303] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 7.864729] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.865199] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 7.865617] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 7.866042] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 7.866411] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 7.869725] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '007' [ 7.870155] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 7.870702] uhci_hcd 0000:00:1d.1: detected 2 ports [ 7.871038] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.871436] uhci_hcd 0000:00:1d.1: Performing full reset [ 7.871798] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 7.872168] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 7.872570] usb usb7: default language 0x0409 [ 7.872896] usb usb7: udev 1, busnum 7, minor = 768 [ 7.873228] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.873629] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.874166] usb usb7: Product: UHCI Host Controller [ 7.874496] usb usb7: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.874895] usb usb7: SerialNumber: 0000:00:1d.1 [ 7.875351] usb usb7: usb_probe_device [ 7.875643] usb usb7: configuration #1 chosen from 1 choice [ 7.876010] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 7.876433] hub 7-0:1.0: usb_probe_interface [ 7.876746] hub 7-0:1.0: usb_probe_interface - got id [ 7.877083] hub 7-0:1.0: USB hub found [ 7.877376] hub 7-0:1.0: 2 ports detected [ 7.877675] hub 7-0:1.0: standalone hub [ 7.877972] hub 7-0:1.0: no power switching (usb 1.0) [ 7.878309] hub 7-0:1.0: individual port over-current protection [ 7.878681] hub 7-0:1.0: power on to power good time: 2ms [ 7.879039] hub 7-0:1.0: local power source is good [ 7.879370] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 7.879802] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.880266] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 7.880683] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 7.881108] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 7.881475] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 7.881827] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '008' [ 7.882240] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 7.882811] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 7.883406] hub 1-0:1.0: port 1: status 0501 change 0001 [ 7.883770] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 7.883775] uhci_hcd 0000:00:1d.2: detected 2 ports [ 7.883780] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.883781] uhci_hcd 0000:00:1d.2: Performing full reset [ 7.883795] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 7.883802] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 7.883849] usb usb8: default language 0x0409 [ 7.883860] usb usb8: udev 1, busnum 8, minor = 896 [ 7.883862] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.883864] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.883866] usb usb8: Product: UHCI Host Controller [ 7.883867] usb usb8: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.883869] usb usb8: SerialNumber: 0000:00:1d.2 [ 7.884019] usb usb8: usb_probe_device [ 7.884021] usb usb8: configuration #1 chosen from 1 choice [ 7.884033] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 7.884120] hub 8-0:1.0: usb_probe_interface [ 7.884122] hub 8-0:1.0: usb_probe_interface - got id [ 7.884123] hub 8-0:1.0: USB hub found [ 7.884131] hub 8-0:1.0: 2 ports detected [ 7.884133] hub 8-0:1.0: standalone hub [ 7.884135] hub 8-0:1.0: no power switching (usb 1.0) [ 7.884136] hub 8-0:1.0: individual port over-current protection [ 7.884138] hub 8-0:1.0: power on to power good time: 2ms [ 7.884147] hub 8-0:1.0: local power source is good [ 7.884149] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 7.884183] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.884273] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 7.884393] Initializing USB Mass Storage driver... [ 7.884479] usbcore: registered new interface driver usb-storage [ 7.884480] USB Mass Storage support registered. [ 7.884594] usbcore: registered new interface driver libusual [ 7.884659] usbcore: registered new interface driver ums-alauda [ 7.884730] usbcore: registered new interface driver ums-cypress [ 7.884795] usbcore: registered new interface driver ums-datafab [ 7.884852] usbcore: registered new interface driver ums-freecom [ 7.884926] usbcore: registered new interface driver ums-isd200 [ 7.884993] usbcore: registered new interface driver ums-jumpshot [ 7.885056] usbcore: registered new interface driver ums-karma [ 7.885123] usbcore: registered new interface driver ums-onetouch [ 7.885188] usbcore: registered new interface driver ums-sddr09 [ 7.885247] usbcore: registered new interface driver ums-sddr55 [ 7.885310] usbcore: registered new interface driver ums-usbat [ 7.885464] usbcore: registered new interface driver usbserial [ 7.885527] USB Serial support registered for generic [ 7.885594] usbcore: registered new interface driver usbserial_generic [ 7.885596] usbserial: USB Serial Driver core [ 7.885647] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 7.885725] usbcore: registered new interface driver belkin [ 7.885727] belkin_sa: v1.3:USB Belkin Serial converter driver [ 7.885789] USB Serial support registered for MCT U232 [ 7.885859] usbcore: registered new interface driver mct_u232 [ 7.885861] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver [ 7.886080] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 7.889265] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 7.889283] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 7.889666] mousedev: PS/2 mouse device common for all mice [ 7.890388] rtc_cmos 00:02: RTC can wake from S4 [ 7.890681] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 7.890708] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 7.890772] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 7.890994] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 7.891140] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 7.891146] iTCO_vendor_support: vendor-support=0 [ 7.891149] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 7.891162] md: linear personality registered for level -1 [ 7.891175] md: raid0 personality registered for level 0 [ 7.891178] md: raid1 personality registered for level 1 [ 7.891181] md: raid10 personality registered for level 10 [ 7.891184] md: raid6 personality registered for level 6 [ 7.891187] md: raid5 personality registered for level 5 [ 7.891189] md: raid4 personality registered for level 4 [ 7.891191] md: multipath personality registered for level -4 [ 7.891194] md: faulty personality registered for level -5 [ 7.891536] device-mapper: uevent: version 1.0.3 [ 7.891861] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com [ 7.891997] device-mapper: multipath: version 1.3.0 loaded [ 7.892007] device-mapper: multipath round-robin: version 1.0.0 loaded [ 7.892010] device-mapper: multipath queue-length: version 0.1.0 loaded [ 7.892012] device-mapper: multipath service-time: version 0.2.0 loaded [ 7.892249] device-mapper: dm-log-userspace: version 1.1.0 loaded [ 7.893856] cpuidle: using governor ladder [ 7.914347] hub 1-0:1.0: port 2: status 0501 change 0001 [ 7.914734] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0 ACK POWER sig=j CSC CONNECT [ 7.915358] hub 1-0:1.0: port 4: status 0501 change 0001 [ 7.915791] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 7.917597] cpuidle: using governor menu [ 7.918087] usbcore: registered new interface driver usbhid [ 7.918444] usbhid: USB HID core driver [ 7.919100] dell_wmi: No known WMI GUID found [ 7.919413] acer_wmi: Acer Laptop ACPI-WMI Extras [ 7.919752] acer_wmi: No or unsupported WMI interface, unable to load [ 7.920512] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0) [ 7.921089] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 7.921697] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 7.922087] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 7.922472] ALSA hda_intel.c:2598 chipset global capabilities = 0x4401 [ 7.922881] ALSA hda_intel.c:1091 Clearing TCSEL [ 7.926600] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 7.926964] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 7.930627] ALSA hda_intel.c:945 codec_mask = 0x4 [ 7.931122] ALSA hda_intel.c:1392 codec #2 probed OK [ 7.936688] ALSA hda_codec.c:3955 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 7.937301] hda_codec: ALC889: SKU not ready 0x411111f0 [ 7.937863] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 7.939548] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00 [ 7.941309] ALSA hda_codec.c:2339 Cannot find slave Side Playback Volume, skipped [ 7.941863] ALSA hda_codec.c:2339 Cannot find slave Headphone Playback Volume, skipped [ 7.942426] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Volume, skipped [ 7.942975] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Volume, skipped [ 7.943581] ALSA hda_codec.c:2339 Cannot find slave Side Playback Switch, skipped [ 7.944130] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Switch, skipped [ 7.944727] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Switch, skipped [ 7.946242] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 7.947233] ALSA device list: [ 7.947502] #0: HDA Intel at 0xf7f00000 irq 45 [ 7.947827] oprofile: using NMI interrupt. [ 7.948176] netem: version 1.3 [ 7.948442] Netfilter messages via NETLINK v0.30. [ 7.948818] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 7.949912] ctnetlink v0.93: registering with nfnetlink. [ 7.950295] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 7.953736] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 7.954128] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.954978] xt_time: kernel timezone is -0000 [ 7.956657] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.957063] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 7.957472] arp_tables: (C) 2002 David S. Miller [ 7.957862] TCP bic registered [ 7.958127] TCP cubic registered [ 7.958397] TCP westwood registered [ 7.958722] TCP highspeed registered [ 7.959005] TCP hybla registered [ 7.959276] TCP htcp registered [ 7.959584] TCP vegas registered [ 7.959855] TCP veno registered [ 7.960122] TCP scalable registered [ 7.960401] TCP lp registered [ 7.960704] TCP yeah registered [ 7.960972] TCP illinois registered [ 7.961251] Initializing XFRM netlink socket [ 7.962311] NET: Registered protocol family 10 [ 7.963567] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.965937] IPv6 over IPv4 tunneling driver [ 7.967971] NET: Registered protocol family 17 [ 7.968297] NET: Registered protocol family 15 [ 7.968777] Bridge firewalling registered [ 7.969088] Ebtables v2.0 registered [ 7.969507] [ 7.969508] printing PIC contents [ 7.969990] ... PIC IMR: ffff [ 7.970256] ... PIC IRR: 0c21 [ 7.970536] ... PIC ISR: 0000 [ 7.970802] ... PIC ELCR: 0c20 [ 7.971069] printing local APIC contents on CPU#0/0: [ 7.971407] ... APIC ID: 00000000 (0) [ 7.971711] ... APIC VERSION: 00060015 [ 7.972001] ... APIC TASKPRI: 00000000 (00) [ 7.972308] ... APIC PROCPRI: 00000000 [ 7.972599] ... APIC LDR: 01000000 [ 7.972877] ... APIC DFR: ffffffff [ 7.973154] ... APIC SPIV: 000001ff [ 7.973435] ... APIC ISR field: [ 7.973703] 0000000000000000000000000000000000000000000000000000000000000000 [ 7.974398] ... APIC TMR field: [ 7.974666] 0000000000000000000000000000000000020000000000000000000000000000 [ 7.975356] ... APIC IRR field: [ 7.975625] 0000000000030000000000000000000000000200000000000000000000000000 [ 7.976319] ... APIC ESR: 00000000 [ 7.976597] ... APIC ICR: 000000ef [ 7.976874] ... APIC ICR2: 03000000 [ 7.977154] ... APIC LVTT: 000000ef [ 7.977435] ... APIC LVTPC: 00000400 [ 7.977719] ... APIC LVT0: 00010700 [ 7.978001] ... APIC LVT1: 00000400 [ 7.978282] ... APIC LVTERR: 000000fe [ 7.978570] ... APIC TMICT: 000208c3 [ 7.978856] ... APIC TMCCT: 000093b8 [ 7.979144] ... APIC TDCR: 00000003 [ 7.979426] [ 7.979634] number of MP IRQ sources: 15. [ 7.979937] number of IO-APIC #8 registers: 24. [ 7.980255] testing the IO APIC....................... [ 7.980614] [ 7.980821] IO APIC #8...... [ 7.981079] .... register #00: 08000000 [ 7.981370] ....... : physical APIC id: 08 [ 7.981725] ....... : Delivery Type: 0 [ 7.982023] ....... : LTS : 0 [ 7.982321] .... register #01: 00170020 [ 7.982655] ....... : max redirection entries: 17 [ 7.982992] ....... : PRQ implemented: 0 [ 7.983300] ....... : IO APIC version: 20 [ 7.983477] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.984011] .... IRQ redirection table: [ 7.984304] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 7.984705] 00 00 1 0 0 0 0 0 0 00 [ 7.985089] 01 00 0 0 0 0 0 0 0 31 [ 7.985527] 02 00 0 0 0 0 0 0 0 30 [ 7.985912] 03 00 0 0 0 0 0 0 0 33 [ 7.986295] 04 00 0 0 0 0 0 0 0 34 [ 7.986724] 05 00 0 0 0 0 0 0 0 35 [ 7.987108] 06 00 1 0 0 0 0 0 0 36 [ 7.987540] 07 00 0 0 0 0 0 0 0 37 [ 7.987925] 08 00 0 0 0 0 0 0 0 38 [ 7.988309] 09 00 0 1 0 0 0 0 0 39 [ 7.988746] 0a 00 0 0 0 0 0 0 0 3A [ 7.989129] 0b 00 0 0 0 0 0 0 0 3B [ 7.989558] 0c 00 0 0 0 0 0 0 0 3C [ 7.989942] 0d 00 0 0 0 0 0 0 0 3D [ 7.990326] 0e 00 0 0 0 0 0 0 0 3E [ 7.990720] 0f 00 0 0 0 0 0 0 0 3F [ 7.991104] 10 00 0 1 0 1 0 0 0 29 [ 7.991500] 11 00 1 1 0 1 0 0 0 41 [ 7.991884] 12 00 0 1 0 1 0 0 0 91 [ 7.992268] 13 00 0 1 0 1 0 0 0 61 [ 7.992664] 14 00 1 1 0 1 0 0 0 71 [ 7.993046] 15 00 0 1 0 1 0 0 0 A1 [ 7.993438] 16 00 1 1 0 1 0 0 0 A9 [ 7.993820] 17 00 0 1 0 1 0 0 0 99 [ 7.994200] IRQ to pin mappings: [ 7.994479] IRQ0 -> 0:2 [ 7.994790] IRQ1 -> 0:1 [ 7.995102] IRQ3 -> 0:3 [ 7.995417] IRQ4 -> 0:4 [ 7.995728] IRQ5 -> 0:5 [ 7.996040] IRQ6 -> 0:6 [ 7.996358] IRQ7 -> 0:7 [ 7.996669] IRQ8 -> 0:8 [ 7.996982] IRQ9 -> 0:9 [ 7.997293] IRQ10 -> 0:10 [ 7.997620] IRQ11 -> 0:11 [ 7.997937] IRQ12 -> 0:12 [ 7.998257] IRQ13 -> 0:13 [ 7.998585] IRQ14 -> 0:14 [ 7.998903] IRQ15 -> 0:15 [ 7.999221] IRQ16 -> 0:16 [ 7.999546] IRQ17 -> 0:17 [ 7.999864] IRQ18 -> 0:18 [ 8.000183] IRQ19 -> 0:19 [ 8.000509] IRQ20 -> 0:20 [ 8.000828] IRQ21 -> 0:21 [ 8.001146] IRQ22 -> 0:22 [ 8.001468] IRQ23 -> 0:23 [ 8.001786] .................................... done. [ 8.002160] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 8.002827] PM: Hibernation image not present or could not be loaded. [ 8.003252] registered taskstats version 1 [ 8.004275] Magic number: 7:784:805 [ 8.004712] rtc_cmos 00:02: setting system clock to 2011-08-16 22:45:56 UTC (1313534756) [ 8.015350] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000 [ 8.015752] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 8.019442] IP-Config: Complete: [ 8.019736] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 8.020369] host=fat, domain=, nis-domain=(none), [ 8.020768] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 8.066463] ehci_hcd 0000:00:1a.7: port 1 high speed [ 8.066820] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 8.118106] usb 1-1: new high speed USB device number 2 using ehci_hcd [ 8.171137] ehci_hcd 0000:00:1a.7: port 1 high speed [ 8.171493] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 8.241564] usb 1-1: default language 0x0409 [ 8.248733] usb 1-1: udev 2, busnum 1, minor = 1 [ 8.249082] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 8.249503] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.249965] usb 1-1: Product: AX88178 [ 8.250271] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 8.250668] usb 1-1: SerialNumber: 000013 [ 8.251383] usb 1-1: usb_probe_device [ 8.251710] usb 1-1: configuration #1 chosen from 1 choice [ 8.252723] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 8.253852] asix 1-1:1.0: usb_probe_interface [ 8.254189] asix 1-1:1.0: usb_probe_interface - got id [ 8.925568] usb usb5: suspend_rh (auto-stop) [ 8.925574] usb usb8: suspend_rh (auto-stop) [ 8.926254] usb usb6: suspend_rh (auto-stop) [ 8.926612] usb usb7: suspend_rh (auto-stop) [ 8.926959] usb usb3: suspend_rh (auto-stop) [ 8.966127] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 8.966905] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '002' [ 8.967460] md: Waiting for all devices to be available before autodetect [ 8.967473] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 8.967488] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 8.967515] usb usb3: wakeup_rh (auto-start) [ 8.969048] md: If you don't use raid, use raid=noautodetect [ 8.970288] md: Autodetecting RAID arrays. [ 8.970619] md: Scanned 0 and added 0 devices. [ 8.970950] md: autorun ... [ 8.971217] md: ... autorun DONE. [ 8.978734] VFS: Mounted root (nfs filesystem) on device 0:16. [ 8.979158] debug: unmapping init memory ffffffff81efa000..ffffffff821aa000 [ 9.018234] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 9.018868] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s [ 9.070226] ehci_hcd 0000:00:1a.7: port 4 high speed [ 9.070592] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.084537] stty used greatest stack depth: 4624 bytes left [ 9.113958] uname used greatest stack depth: 3728 bytes left [ 9.124937] usb 1-4: new high speed USB device number 4 using ehci_hcd [ 9.156711] sh used greatest stack depth: 3696 bytes left [ 9.175707] usb usb4: suspend_rh (auto-stop) [ 9.176026] ehci_hcd 0000:00:1a.7: port 4 high speed [ 9.176033] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.527187] modprobe used greatest stack depth: 3616 bytes left [ 9.574795] edd_id used greatest stack depth: 3504 bytes left [ 10.175079] usb 1-4: default language 0x0409 [ 10.176940] usb 1-4: udev 4, busnum 1, minor = 3 [ 10.177277] usb 1-4: New USB device found, idVendor=1307, idProduct=0165 [ 10.177731] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.178169] usb 1-4: Product: USB Mass Storage Device [ 10.178526] usb 1-4: Manufacturer: Teclast Technology [ 10.178933] usb 1-4: SerialNumber: 0000000000020D [ 10.179478] usb 1-4: usb_probe_device [ 10.179828] usb 1-4: configuration #1 chosen from 1 choice [ 10.180313] usb 1-4: adding 1-4:1.0 (config #1, interface 0) [ 10.180806] usb-storage 1-4:1.0: usb_probe_interface [ 10.181141] usb-storage 1-4:1.0: usb_probe_interface - got id [ 10.181782] scsi9 : usb-storage 1-4:1.0 [ 10.182314] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '004' [ 10.182844] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 10.183204] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 10.183559] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 10.287395] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 10.388989] usb 3-2: new low speed USB device number 2 using uhci_hcd [ 10.393113] usb 3-2: uhci_result_common: failed with status 440000 [ 10.397098] usb 3-2: uhci_result_common: failed with status 440000 [ 10.401087] usb 3-2: uhci_result_common: failed with status 440000 [ 10.502635] usb 3-2: device descriptor read/64, error -71 [ 10.606488] usb 3-2: uhci_result_common: failed with status 440000 [ 10.610440] usb 3-2: uhci_result_common: failed with status 440000 [ 10.614426] usb 3-2: uhci_result_common: failed with status 440000 [ 10.716073] usb 3-2: device descriptor read/64, error -71 [ 10.919410] usb 3-2: new low speed USB device number 3 using uhci_hcd [ 10.923475] usb 3-2: uhci_result_common: failed with status 440000 [ 10.927458] usb 3-2: uhci_result_common: failed with status 440000 [ 10.931448] usb 3-2: uhci_result_common: failed with status 440000 [ 11.033089] usb 3-2: device descriptor read/64, error -71 [ 11.136809] usb 3-2: uhci_result_common: failed with status 440000 [ 11.140795] usb 3-2: uhci_result_common: failed with status 440000 [ 11.144782] usb 3-2: uhci_result_common: failed with status 440000 [ 11.179660] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 11.192735] EXT4-fs (sda5): recovery complete [ 11.193153] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 11.247372] usb 3-2: device descriptor read/64, error -71 [ 11.292178] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 11.293452] sd 9:0:0:0: [sdb] Write Protect is off [ 11.293798] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 11.294887] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.295271] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.299902] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.300297] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.434179] sdb: sdb1 sdb2 sdb3 [ 11.437561] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.437954] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.438343] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 11.449792] usb 3-2: new low speed USB device number 4 using uhci_hcd [ 11.453826] usb 3-2: uhci_result_common: failed with status 440000 [ 11.657196] usb 3-2: uhci_result_common: failed with status 440000 [ 11.857524] usb 3-2: device not accepting address 4, error -71 [ 11.929410] svc: failed to register lockdv1 RPC service (errno 97). [ 11.931494] mount.nfs used greatest stack depth: 3104 bytes left [ 11.959162] usb 3-2: new low speed USB device number 5 using uhci_hcd [ 11.963247] usb 3-2: uhci_result_common: failed with status 440000 [ 12.167610] usb 3-2: uhci_result_common: failed with status 440000 [ 12.367840] usb 3-2: device not accepting address 5, error -71 [ 12.368245] hub 3-0:1.0: unable to enumerate USB device on port 2 [ 12.368650] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.369065] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 12.369446] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 18.114997] eth0: no IPv6 routers present [ 46.628273] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)