[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.0.0-next-20110802+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #556 SMP Thu Aug 11 16:49:45 CST 2011 [ 0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcde3000 (usable) [ 0.000000] BIOS-e820: 00000000bcde3000 - 00000000bcffb000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcffb000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf800000 [ 0.000000] 0000000000 - 00bf800000 page 4k [ 0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000 [ 0.000000] log_buf_len: 8388608 [ 0.000000] early log buf free: 258269(98%) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-00000000bf800000 [ 0.000000] Initmem setup node 0 0000000000000000-00000000bf800000 [ 0.000000] NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff] [ 0.000000] [ffffea0000000000-ffffea0002ffffff] PMD -> [ffff8800b9c00000-ffff8800bcbfffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x000bcde3 [ 0.000000] 0: 0x000bcffb -> 0x000bf6bd [ 0.000000] 0: 0x000bf6bf -> 0x000bf714 [ 0.000000] 0: 0x000bf7bf -> 0x000bf7e7 [ 0.000000] 0: 0x000bf7ff -> 0x000bf800 [ 0.000000] On node 0 totalpages: 783535 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3911 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 12192 pages used for memmap [ 0.000000] DMA32 zone: 767363 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bcde3000 - 00000000bcffb000 [ 0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915520 r8192 d21888 u2097152 [ 0.000000] pcpu-alloc: s1915520 r8192 d21888 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 771274 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Memory: 3012792k/3137536k available (9617k kernel code, 3396k absent, 121348k reserved, 5708k data, 2752k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=16, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] NR_IRQS:4352 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6335 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 25165824 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.001000] Fast TSC calibration using PIT [ 0.002000] Detected 3199.822 MHz processor. [ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.64 BogoMIPS (lpj=3199822) [ 0.000709] pid_max: default: 32768 minimum: 301 [ 0.001889] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003951] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.004951] Mount-cache hash table entries: 256 [ 0.005659] Initializing cgroup subsys debug [ 0.005969] Initializing cgroup subsys cpuacct [ 0.006303] Initializing cgroup subsys memory [ 0.006641] Initializing cgroup subsys devices [ 0.006957] Initializing cgroup subsys freezer [ 0.007283] Initializing cgroup subsys blkio [ 0.007647] CPU: Physical Processor ID: 0 [ 0.007945] CPU: Processor Core ID: 0 [ 0.008245] mce: CPU supports 9 MCE banks [ 0.008550] CPU0: Thermal monitoring enabled (TM1) [ 0.008889] using mwait in idle threads. [ 0.010042] ACPI: Core revision 20110623 [ 0.021789] ftrace: allocating 36662 entries in 144 pages [ 0.030391] Getting VERSION: 60015 [ 0.030669] Getting VERSION: 60015 [ 0.030945] Getting ID: 0 [ 0.031202] Getting ID: 0 [ 0.031449] Switched APIC routing to physical flat. [ 0.031781] enabled ExtINT on CPU#0 [ 0.032225] ENABLING IO-APIC IRQs [ 0.032498] init IO_APIC IRQs [ 0.032758] apic 8 pin 0 not connected [ 0.033058] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0) [ 0.033634] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0) [ 0.034209] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) [ 0.034775] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0) [ 0.035344] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0) [ 0.035910] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0) [ 0.036480] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0) [ 0.037046] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 0.037616] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0) [ 0.038185] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0) [ 0.038757] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0) [ 0.039332] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0) [ 0.039904] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 0.040478] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0) [ 0.041050] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0) [ 0.041622] apic 8 pin 16 not connected [ 0.041917] apic 8 pin 17 not connected [ 0.042217] apic 8 pin 18 not connected [ 0.042512] apic 8 pin 19 not connected [ 0.042807] apic 8 pin 20 not connected [ 0.043102] apic 8 pin 21 not connected [ 0.043399] apic 8 pin 22 not connected [ 0.043695] apic 8 pin 23 not connected [ 0.044125] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.054500] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.054981] Using local APIC timer interrupts. [ 0.054982] calibrating APIC timer ... [ 0.157161] ... lapic delta = 833233 [ 0.157444] ... PM-Timer delta = 357899 [ 0.157735] ... PM-Timer result ok [ 0.158011] ..... delta 833233 [ 0.158274] ..... mult: 35792525 [ 0.158543] ..... calibration result: 133317 [ 0.158851] ..... CPU clock speed is 3199.0616 MHz. [ 0.159181] ..... host bus clock speed is 133.0317 MHz. [ 0.159538] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver. [ 0.160301] ... version: 3 [ 0.160603] ... bit width: 48 [ 0.160905] ... generic registers: 4 [ 0.161204] ... value mask: 0000ffffffffffff [ 0.161553] ... max period: 000000007fffffff [ 0.161900] ... fixed-purpose events: 3 [ 0.162199] ... event mask: 000000070000000f [ 0.162829] lockdep: fixing up alternatives. [ 0.163193] Booting Node 0, Processors #1 [ 0.163412] smpboot cpu 1: start_ip = 97000 [ 0.174985] masked ExtINT on CPU#1 [ 0.254720] lockdep: fixing up alternatives. [ 0.255052] #2 [ 0.255145] smpboot cpu 2: start_ip = 97000 [ 0.266723] masked ExtINT on CPU#2 [ 0.346684] lockdep: fixing up alternatives. [ 0.347019] #3 [ 0.347111] smpboot cpu 3: start_ip = 97000 [ 0.358684] masked ExtINT on CPU#3 [ 0.438710] lockdep: fixing up alternatives. [ 0.439046] #4 [ 0.439139] smpboot cpu 4: start_ip = 97000 [ 0.450712] masked ExtINT on CPU#4 [ 0.530599] lockdep: fixing up alternatives. [ 0.530933] #5 [ 0.531026] smpboot cpu 5: start_ip = 97000 [ 0.542600] masked ExtINT on CPU#5 [ 0.622642] lockdep: fixing up alternatives. [ 0.622977] #6 [ 0.623069] smpboot cpu 6: start_ip = 97000 [ 0.637619] masked ExtINT on CPU#6 [ 0.717538] lockdep: fixing up alternatives. [ 0.717872] #7 [ 0.717964] smpboot cpu 7: start_ip = 97000 [ 0.729535] masked ExtINT on CPU#7 [ 0.809469] Brought up 8 CPUs [ 0.809732] Total of 8 processors activated (51187.32 BogoMIPS). [ 0.813412] CPU0 attaching sched-domain: [ 0.813711] domain 0: span 0,4 level SIBLING [ 0.814055] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 0.814589] domain 1: span 0-7 level MC [ 0.814920] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.815880] CPU1 attaching sched-domain: [ 0.816176] domain 0: span 1,5 level SIBLING [ 0.816524] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 0.817054] domain 1: span 0-7 level MC [ 0.817389] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.818344] CPU2 attaching sched-domain: [ 0.818642] domain 0: span 2,6 level SIBLING [ 0.818986] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 0.819520] domain 1: span 0-7 level MC [ 0.819852] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.820810] CPU3 attaching sched-domain: [ 0.821106] domain 0: span 3,7 level SIBLING [ 0.821454] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 0.821985] domain 1: span 0-7 level MC [ 0.822317] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.823275] CPU4 attaching sched-domain: [ 0.823573] domain 0: span 0,4 level SIBLING [ 0.823917] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 0.824451] domain 1: span 0-7 level MC [ 0.824783] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.825741] CPU5 attaching sched-domain: [ 0.826036] domain 0: span 1,5 level SIBLING [ 0.826383] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 0.826916] domain 1: span 0-7 level MC [ 0.827248] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.828675] CPU6 attaching sched-domain: [ 0.828970] domain 0: span 2,6 level SIBLING [ 0.829314] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 0.829849] domain 1: span 0-7 level MC [ 0.830181] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.831138] CPU7 attaching sched-domain: [ 0.831438] domain 0: span 3,7 level SIBLING [ 0.831783] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 0.832313] domain 1: span 0-7 level MC [ 0.832649] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.834035] devtmpfs: initialized [ 0.834484] kworker/u:0 used greatest stack depth: 5608 bytes left [ 0.834866] kworker/u:0 used greatest stack depth: 5192 bytes left [ 0.836631] PM: Registering ACPI NVS region at bcde3000 (2195456 bytes) [ 0.837088] PM: Registering ACPI NVS region at bf714000 (700416 bytes) [ 0.838147] xor: automatically using best checksumming function: generic_sse [ 0.843348] generic_sse: 11928.000 MB/sec [ 0.843657] xor: using function: generic_sse (11928.000 MB/sec) [ 0.844103] RTC time: 17:04:43, date: 08/11/11 [ 0.844515] NET: Registered protocol family 16 [ 0.845485] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.846039] ACPI: bus type pci registered [ 0.846534] dca service started, version 1.12.1 [ 0.846930] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.847549] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 0.859845] PCI: Using configuration type 1 for base access [ 0.882328] bio: create slab at 0 [ 0.899337] raid6: int64x1 3167 MB/s [ 0.916332] raid6: int64x2 3421 MB/s [ 0.933329] raid6: int64x4 2738 MB/s [ 0.950323] raid6: int64x8 2089 MB/s [ 0.967318] raid6: sse2x1 7921 MB/s [ 0.984314] raid6: sse2x2 9292 MB/s [ 1.001308] raid6: sse2x4 10753 MB/s [ 1.001598] raid6: using algorithm sse2x4 (10753 MB/s) [ 1.002019] ACPI: Added _OSI(Module Device) [ 1.002332] ACPI: Added _OSI(Processor Device) [ 1.002648] ACPI: Added _OSI(3.0 _SCP Extensions) [ 1.002973] ACPI: Added _OSI(Processor Aggregator Device) [ 1.007267] ACPI: EC: Look up EC in DSDT [ 1.028437] ACPI: Interpreter enabled [ 1.028724] ACPI: (supports S0 S1 S3 S4 S5) [ 1.029232] ACPI: Using IOAPIC for interrupt routing [ 1.041714] ACPI: No dock devices found. [ 1.042012] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.043230] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 1.044843] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 1.045239] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 1.045639] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.046176] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 1.046717] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 1.047255] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 1.047817] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 1.048256] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 1.048690] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.049068] pci 0000:00:01.0: PME# disabled [ 1.049401] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 1.049827] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 1.050205] pci 0000:00:03.0: PME# disabled [ 1.050541] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 1.050966] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 1.051348] pci 0000:00:07.0: PME# disabled [ 1.051682] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 1.052127] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 1.052578] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 1.053022] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 1.053473] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 1.053913] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 1.054366] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 1.054756] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 1.055141] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 1.055530] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 1.055938] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.056319] pci 0000:00:19.0: PME# disabled [ 1.056645] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 1.057066] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 1.057477] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 1.057899] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 1.058305] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 1.058728] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 1.059140] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 1.059534] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 1.059994] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 1.060376] pci 0000:00:1a.7: PME# disabled [ 1.060704] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 1.061091] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 1.061558] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.061936] pci 0000:00:1b.0: PME# disabled [ 1.062261] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 1.062702] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.063080] pci 0000:00:1c.0: PME# disabled [ 1.063411] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 1.063848] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.064226] pci 0000:00:1c.1: PME# disabled [ 1.064560] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 1.064998] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.065379] pci 0000:00:1c.4: PME# disabled [ 1.065711] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 1.066133] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 1.066540] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 1.066961] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 1.067368] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 1.067790] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 1.068205] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 1.068600] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 1.069061] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 1.069443] pci 0000:00:1d.7: PME# disabled [ 1.069767] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 1.070207] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 1.070679] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 1.071062] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 1.071614] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 1.072205] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 1.072599] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 1.072957] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 1.073319] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 1.073679] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 1.074038] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 1.074401] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 1.074815] pci 0000:00:1f.2: PME# supported from D3hot [ 1.075161] pci 0000:00:1f.2: PME# disabled [ 1.075489] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 1.075876] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 1.076299] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 1.076726] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.077132] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 1.077515] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 1.080878] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 1.081309] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 1.081725] pci 0000:02:00.0: supports D1 D2 [ 1.082055] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 1.082439] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 1.082880] pci 0000:02:00.1: supports D1 D2 [ 1.083206] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.083557] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.083962] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.084562] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.084962] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.085368] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.085795] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 1.086185] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 1.086554] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 1.086918] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 1.087285] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 1.087651] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 1.088016] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 1.088458] pci 0000:06:00.0: supports D1 [ 1.088756] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 1.089123] pci 0000:06:00.0: PME# disabled [ 1.089451] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.089798] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.090176] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.090628] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 1.091017] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 1.091407] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 1.091855] pci 0000:07:03.0: supports D1 D2 [ 1.092163] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 1.092550] pci 0000:07:03.0: PME# disabled [ 1.092908] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 1.093327] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.093735] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.094298] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.094858] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.095446] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 1.096031] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 1.096620] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 1.097241] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.098543] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 1.099172] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 1.099644] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 1.100110] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 1.100582] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 1.101050] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 1.101534] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 1.102093] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19) [ 1.124728] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.125813] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.126894] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.127976] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.129060] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.130144] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.131224] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.132314] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.133622] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.134196] vgaarb: loaded [ 1.134453] vgaarb: bridge control possible 0000:02:00.0 [ 1.135008] SCSI subsystem initialized [ 1.135472] libata version 3.00 loaded. [ 1.136017] usbcore: registered new interface driver usbfs [ 1.136434] usbcore: registered new interface driver hub [ 1.136854] usbcore: registered new device driver usb [ 1.137620] wmi: Mapper loaded [ 1.137946] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 1.138337] PCI: Using ACPI for IRQ routing [ 1.140210] PCI: Discovered peer bus 3f [ 1.140581] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600 [ 1.140980] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600 [ 1.141391] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600 [ 1.141788] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600 [ 1.142189] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600 [ 1.142590] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600 [ 1.142988] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600 [ 1.143390] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600 [ 1.143786] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600 [ 1.144183] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600 [ 1.144583] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600 [ 1.144983] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600 [ 1.145387] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600 [ 1.145783] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600 [ 1.146180] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600 [ 1.146584] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600 [ 1.146979] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600 [ 1.147379] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600 [ 1.147778] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600 [ 1.149529] PCI: pci_cache_line_size set to 64 bytes [ 1.150093] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 1.150360] reserve RAM buffer: 00000000bcde3000 - 00000000bfffffff [ 1.150781] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff [ 1.151201] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff [ 1.151625] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff [ 1.152044] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff [ 1.178107] pnp: PnP ACPI init [ 1.178555] ACPI: bus type pnp registered [ 1.179475] pnp 00:00: [bus 00-3d] [ 1.179754] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.180057] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.180388] pnp 00:00: [io 0x0d00-0xffff window] [ 1.180714] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.181064] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 1.181421] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 1.181773] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 1.182123] pnp 00:00: [mem 0x00000000 window] [ 1.182576] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 1.183247] pnp 00:01: [io 0x0000-0x000f] [ 1.183555] pnp 00:01: [io 0x0081-0x0083] [ 1.183858] pnp 00:01: [io 0x0087] [ 1.184138] pnp 00:01: [io 0x0089-0x008b] [ 1.184444] pnp 00:01: [io 0x008f] [ 1.184724] pnp 00:01: [io 0x00c0-0x00df] [ 1.185025] pnp 00:01: [dma 4] [ 1.185389] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.185796] pnp 00:02: [io 0x0070-0x0071] [ 1.186098] pnp 00:02: [io 0x0074-0x0077] [ 1.186412] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 1.186977] pnp 00:02: [irq 8] [ 1.187341] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.187756] pnp 00:03: [io 0x00f0] [ 1.188038] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 1.188613] pnp 00:03: [irq 13] [ 1.188971] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.189388] pnp 00:04: [io 0x0061] [ 1.189760] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.190169] pnp 00:05: [io 0x0500-0x053f] [ 1.190475] pnp 00:05: [io 0x0400-0x047f] [ 1.190777] pnp 00:05: [io 0x0092] [ 1.191057] pnp 00:05: [io 0x0680-0x06ff] [ 1.191363] pnp 00:05: [io 0x0010-0x001f] [ 1.191665] pnp 00:05: [io 0x0072-0x0073] [ 1.191967] pnp 00:05: [io 0x0080] [ 1.192246] pnp 00:05: [io 0x0084-0x0086] [ 1.192552] pnp 00:05: [io 0x0088] [ 1.192832] pnp 00:05: [io 0x008c-0x008e] [ 1.193134] pnp 00:05: [io 0x0090-0x009f] [ 1.193619] system 00:05: [io 0x0500-0x053f] has been reserved [ 1.193991] system 00:05: [io 0x0400-0x047f] has been reserved [ 1.194366] system 00:05: [io 0x0680-0x06ff] has been reserved [ 1.194739] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.195220] pnp 00:06: [io 0x0060] [ 1.195505] pnp 00:06: [io 0x0064] [ 1.195944] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.196888] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 1.197332] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 1.197858] pnp: PnP ACPI: found 8 devices [ 1.198161] ACPI: ACPI bus type pnp unregistered [ 1.209129] Switching to clocksource acpi_pm [ 1.209576] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 1.210191] PCI: max bus depth: 1 pci_try_num: 2 [ 1.210299] Switched to NOHz mode on CPU #6 [ 1.210306] Switched to NOHz mode on CPU #4 [ 1.210336] Switched to NOHz mode on CPU #2 [ 1.210340] Switched to NOHz mode on CPU #1 [ 1.210352] Switched to NOHz mode on CPU #7 [ 1.210367] Switched to NOHz mode on CPU #5 [ 1.210391] Switched to NOHz mode on CPU #3 [ 1.212671] Switched to NOHz mode on CPU #0 [ 1.213037] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.213392] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 1.216908] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.217255] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.217668] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.218225] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.218577] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.218936] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.219290] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.219644] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.220023] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.220432] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 1.220788] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.221210] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0) [ 1.221792] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.222194] pci 0000:00:01.0: setting latency timer to 64 [ 1.222549] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.222954] pci 0000:00:03.0: setting latency timer to 64 [ 1.223310] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.223720] pci 0000:00:07.0: setting latency timer to 64 [ 1.224080] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0) [ 1.224659] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.225061] pci 0000:00:1c.0: setting latency timer to 64 [ 1.225417] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 1.225828] pci 0000:00:1c.1: setting latency timer to 64 [ 1.226184] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.226584] pci 0000:00:1c.4: setting latency timer to 64 [ 1.226946] pci 0000:00:1e.0: setting latency timer to 64 [ 1.227299] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.227665] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.228021] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.228403] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.228794] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.229176] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.229557] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 1.229945] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.230480] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 1.230842] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 1.231224] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 1.231606] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 1.231968] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 1.232324] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 1.232716] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.233097] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.233479] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.233868] pci_bus 0000:3f: resource 0 [io 0x0000-0xffff] [ 1.234223] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff] [ 1.234677] NET: Registered protocol family 2 [ 1.235302] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.237717] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.241456] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) [ 1.244373] TCP: Hash tables configured (established 524288 bind 65536) [ 1.244798] TCP reno registered [ 1.245131] UDP hash table entries: 2048 (order: 6, 393216 bytes) [ 1.245743] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes) [ 1.246452] NET: Registered protocol family 1 [ 1.246983] RPC: Registered named UNIX socket transport module. [ 1.247355] RPC: Registered udp transport module. [ 1.247695] RPC: Registered tcp transport module. [ 1.248020] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.248452] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.248854] pci 0000:00:1a.0: Performing full reset [ 1.249204] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.249596] pci 0000:00:1a.1: Performing full reset [ 1.249951] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.250343] pci 0000:00:1a.2: Performing full reset [ 1.250852] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.251245] pci 0000:00:1d.0: Performing full reset [ 1.251592] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.252004] pci 0000:00:1d.1: Performing full reset [ 1.252356] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.252761] pci 0000:00:1d.2: Performing full reset [ 1.253254] pci 0000:02:00.0: Boot video device [ 1.253638] PCI: CLS 64 bytes, default 64 [ 1.257786] Machine check injector initialized [ 1.259968] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 1.260342] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 1.260723] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 1.261093] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 1.261465] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 1.261844] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 1.262216] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 1.262586] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 1.263046] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 1.264147] audit: initializing netlink socket (disabled) [ 1.264521] type=2000 audit(1313082283.015:1): initialized [ 1.294349] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.306409] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.307363] fuse init (API version 7.16) [ 1.308288] JFS: nTxBlock = 8192, nTxLock = 65536 [ 1.311849] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.314714] NILFS version 2 loaded [ 1.316037] Btrfs loaded [ 1.316288] msgmni has been set to 5884 [ 1.317741] async_tx: api initialized (async) [ 1.318268] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.318883] io scheduler noop registered [ 1.319181] io scheduler deadline registered [ 1.319650] io scheduler cfq registered (default) [ 1.320395] pcieport 0000:00:1c.0: setting latency timer to 64 [ 1.320837] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 1.321314] pcieport 0000:00:1c.1: setting latency timer to 64 [ 1.321748] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 1.322222] pcieport 0000:00:1c.4: setting latency timer to 64 [ 1.322656] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 1.323350] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.324163] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 1.324766] ACPI: Sleep Button [SLPB] [ 1.325178] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.325742] ACPI: Power Button [PWRF] [ 1.326756] ACPI: acpi_idle registered with cpuidle [ 1.327491] Monitor-Mwait will be used to enter C-1 state [ 1.327904] Monitor-Mwait will be used to enter C-3 state [ 1.335381] ioatdma: Intel(R) QuickData Technology Driver 4.00 [ 1.386682] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.408719] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 1.456916] Initializing Nozomi driver 2.1d [ 1.457749] Non-volatile memory driver v1.3 [ 1.458495] Linux agpgart interface v0.103 [ 1.458892] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 1.459491] Hangcheck: Using getrawmonotonic(). [ 1.459883] [drm] Initialized drm 1.1.0 20060810 [ 1.460205] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 2.255710] Refined TSC clocksource calibration: 3200.113 MHz. [ 2.256079] Switching to clocksource tsc [ 4.479844] floppy0: no floppy controllers found [ 4.611713] brd: module loaded [ 4.613588] loop: module loaded [ 4.614316] Loading iSCSI transport class v2.0-870. [ 4.615218] Loading Adaptec I2O RAID: Version 2.4 Build 5go [ 4.615575] Detecting Adaptec I2O RAID controllers... [ 4.616090] Adaptec aacraid driver 1.1-7[28000]-ms [ 4.616970] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 4.617556] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.03-k. [ 4.618279] iscsi: registered transport (qla4xxx) [ 4.618674] QLogic iSCSI HBA Driver [ 4.619036] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) [ 4.619655] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) [ 4.620144] megasas: 00.00.05.40-rc1 Tue. Jul. 26 17:00:00 PDT 2011 [ 4.620606] mpt2sas version 09.100.00.00 loaded [ 4.621310] ahci 0000:00:1f.2: version 3.0 [ 4.621643] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0) [ 4.622220] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.622666] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 4.623081] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 4.623652] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 4.624219] ahci 0000:00:1f.2: setting latency timer to 64 [ 4.634999] scsi0 : ahci [ 4.635437] scsi1 : ahci [ 4.635840] scsi2 : ahci [ 4.636242] scsi3 : ahci [ 4.636633] scsi4 : ahci [ 4.637035] scsi5 : ahci [ 4.637675] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43 [ 4.638221] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43 [ 4.638766] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 4.639307] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 4.639853] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 4.643377] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 4.643951] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.644366] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 4.645033] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 4.645440] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 4.645852] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 4.646223] ahci: SSS flag set, parallel bus scan disabled [ 4.646616] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 4.647184] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 4.647559] ahci 0000:06:00.0: setting latency timer to 64 [ 4.648703] scsi6 : ahci [ 4.649114] scsi7 : ahci [ 4.649511] scsi8 : ahci [ 4.649889] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 4.650433] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 4.650977] ata9: DUMMY [ 4.653557] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 4.653975] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 4.654426] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k [ 4.654801] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 4.655198] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0) [ 4.655771] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 4.656184] e1000e 0000:00:19.0: setting latency timer to 64 [ 4.656652] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 4.847265] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54 [ 4.847836] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.848275] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 4.848767] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k [ 4.849159] Copyright (c) 2007-2011 Intel Corporation. [ 4.849584] Intel(R) Virtual Function Network Driver - version 2.0.0-k [ 4.849982] Copyright (c) 2009 - 2010 Intel Corporation. [ 4.850413] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k [ 4.850969] ixgbe: Copyright (c) 1999-2011 Intel Corporation. [ 4.851416] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 4.851837] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 4.852594] jme: JMicron JMC2XX ethernet driver version 1.0.8 [ 4.853276] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 4.853937] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011) [ 4.854607] sky2: driver version 1.29 [ 4.855942] tun: Universal TUN/TAP device driver, 1.6 [ 4.856281] tun: (C) 1999-2004 Max Krasnyansky [ 4.856993] usbcore: registered new interface driver catc [ 4.857345] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 4.857776] usbcore: registered new interface driver kaweth [ 4.858134] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 4.858746] usbcore: registered new interface driver pegasus [ 4.859106] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 4.859570] usbcore: registered new interface driver rtl8150 [ 4.859992] usbcore: registered new interface driver asix [ 4.860396] usbcore: registered new interface driver cdc_ether [ 4.860825] usbcore: registered new interface driver cdc_eem [ 4.861242] usbcore: registered new interface driver dm9601 [ 4.861666] usbcore: registered new interface driver smsc75xx [ 4.862098] usbcore: registered new interface driver smsc95xx [ 4.862520] usbcore: registered new interface driver gl620a [ 4.862937] usbcore: registered new interface driver net1080 [ 4.863356] usbcore: registered new interface driver plusb [ 4.863843] usbcore: registered new interface driver rndis_host [ 4.864269] usbcore: registered new interface driver cdc_subset [ 4.864692] usbcore: registered new interface driver zaurus [ 4.865111] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 4.865712] usbcore: registered new interface driver int51x1 [ 4.866078] cdc_ncm: 01-June-2011 [ 4.866406] usbcore: registered new interface driver cdc_ncm [ 4.866773] netconsole: local port 6665 [ 4.867066] netconsole: local IP 10.0.0.0 [ 4.867364] netconsole: interface 'eth0' [ 4.867660] netconsole: remote port 6666 [ 4.867959] netconsole: remote IP 192.168.1.1 [ 4.868271] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 4.868647] netconsole: device eth0 not up yet, forcing it [ 4.948780] ata5: SATA link down (SStatus 0 SControl 300) [ 4.949152] ata4: SATA link down (SStatus 0 SControl 300) [ 4.949526] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.949934] ata3: SATA link down (SStatus 0 SControl 300) [ 4.950307] ata6: SATA link down (SStatus 0 SControl 300) [ 4.955784] ata7: SATA link down (SStatus 0 SControl 300) [ 4.964028] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 4.995966] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 4.996327] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 5.014833] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.054267] ata1.00: configured for UDMA/133 [ 5.054764] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 5.055664] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 5.056326] sd 0:0:0:0: [sda] Write Protect is off [ 5.056656] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.057048] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.146300] sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 > [ 5.147819] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.306887] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 5.383631] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 5.384027] ata2.00: applying bridge limits [ 5.414875] ata2.00: configured for UDMA/33 [ 5.416157] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 5.721811] ata8: SATA link down (SStatus 0 SControl 300) [ 7.733743] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 7.736022] console [netcon0] enabled [ 7.736311] netconsole: network logging started [ 7.736696] Fusion MPT base driver 3.04.19 [ 7.737005] Copyright (c) 1999-2008 LSI Corporation [ 7.737345] Fusion MPT SPI Host driver 3.04.19 [ 7.737742] Fusion MPT FC Host driver 3.04.19 [ 7.738140] Fusion MPT SAS Host driver 3.04.19 [ 7.738534] Fusion MPT misc device (ioctl) driver 3.04.19 [ 7.738980] mptctl: Registered with Fusion MPT base driver [ 7.739336] mptctl: /dev/mptctl @ (major,minor=10,220) [ 7.739778] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.740176] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 7.740587] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0) [ 7.741163] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 7.741591] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 7.741964] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 7.742371] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file 'devices' [ 7.742928] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.743349] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 7.743905] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 7.744507] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 7.745161] ehci_hcd 0000:00:1a.7: debug port 1 [ 7.745484] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.749968] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 7.750371] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 7.750755] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 7.751122] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.755611] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 7.761866] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 7.762301] usb usb1: default language 0x0409 [ 7.762623] usb usb1: udev 1, busnum 1, minor = 0 [ 7.762954] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.763358] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.763897] usb usb1: Product: EHCI Host Controller [ 7.764230] usb usb1: Manufacturer: Linux 3.0.0-next-20110802+ ehci_hcd [ 7.764627] usb usb1: SerialNumber: 0000:00:1a.7 [ 7.765102] usb usb1: usb_probe_device [ 7.765395] usb usb1: configuration #1 chosen from 1 choice [ 7.765780] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 7.766230] hub 1-0:1.0: usb_probe_interface [ 7.766542] hub 1-0:1.0: usb_probe_interface - got id [ 7.766886] hub 1-0:1.0: USB hub found [ 7.767183] hub 1-0:1.0: 6 ports detected [ 7.767483] hub 1-0:1.0: standalone hub [ 7.767779] hub 1-0:1.0: no power switching (usb 1.0) [ 7.768120] hub 1-0:1.0: individual port over-current protection [ 7.768495] hub 1-0:1.0: power on to power good time: 20ms [ 7.768871] hub 1-0:1.0: local power source is good [ 7.769205] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 7.769656] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.770186] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0) [ 7.770760] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 7.771192] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 7.771562] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 7.771917] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '002' [ 7.772332] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 7.772885] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 7.776468] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 7.777109] ehci_hcd 0000:00:1d.7: debug port 1 [ 7.777430] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.781921] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 7.782325] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 7.782709] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 7.783077] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.787564] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 7.793864] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 7.794282] usb usb2: default language 0x0409 [ 7.794603] usb usb2: udev 1, busnum 2, minor = 128 [ 7.794940] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.795343] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.795882] usb usb2: Product: EHCI Host Controller [ 7.796215] usb usb2: Manufacturer: Linux 3.0.0-next-20110802+ ehci_hcd [ 7.796611] usb usb2: SerialNumber: 0000:00:1d.7 [ 7.797073] usb usb2: usb_probe_device [ 7.797366] usb usb2: configuration #1 chosen from 1 choice [ 7.797731] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 7.798163] hub 2-0:1.0: usb_probe_interface [ 7.798474] hub 2-0:1.0: usb_probe_interface - got id [ 7.798813] hub 2-0:1.0: USB hub found [ 7.799110] hub 2-0:1.0: 6 ports detected [ 7.799410] hub 2-0:1.0: standalone hub [ 7.799704] hub 2-0:1.0: no power switching (usb 1.0) [ 7.800047] hub 2-0:1.0: individual port over-current protection [ 7.800421] hub 2-0:1.0: power on to power good time: 20ms [ 7.800781] hub 2-0:1.0: local power source is good [ 7.801116] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 7.801564] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.802122] uhci_hcd: USB Universal Host Controller Interface driver [ 7.802554] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 7.802980] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 7.803350] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 7.803701] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '003' [ 7.804118] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 7.804665] uhci_hcd 0000:00:1a.0: detected 2 ports [ 7.805003] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.805402] uhci_hcd 0000:00:1a.0: Performing full reset [ 7.805763] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 7.806133] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 7.806549] usb usb3: default language 0x0409 [ 7.806875] usb usb3: udev 1, busnum 3, minor = 256 [ 7.807208] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.807611] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.808152] usb usb3: Product: UHCI Host Controller [ 7.808485] usb usb3: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.808884] usb usb3: SerialNumber: 0000:00:1a.0 [ 7.809344] usb usb3: usb_probe_device [ 7.809637] usb usb3: configuration #1 chosen from 1 choice [ 7.810006] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 7.810436] hub 3-0:1.0: usb_probe_interface [ 7.810747] hub 3-0:1.0: usb_probe_interface - got id [ 7.811090] hub 3-0:1.0: USB hub found [ 7.811385] hub 3-0:1.0: 2 ports detected [ 7.811686] hub 3-0:1.0: standalone hub [ 7.811983] hub 3-0:1.0: no power switching (usb 1.0) [ 7.812323] hub 3-0:1.0: individual port over-current protection [ 7.812698] hub 3-0:1.0: power on to power good time: 2ms [ 7.813058] hub 3-0:1.0: local power source is good [ 7.813392] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 7.813820] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.814281] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 7.814715] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0) [ 7.815293] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 7.815714] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 7.816087] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 7.816439] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '004' [ 7.816856] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 7.817403] uhci_hcd 0000:00:1a.1: detected 2 ports [ 7.817738] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.818141] uhci_hcd 0000:00:1a.1: Performing full reset [ 7.818502] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 7.818887] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 7.819287] usb usb4: default language 0x0409 [ 7.819608] usb usb4: udev 1, busnum 4, minor = 384 [ 7.819944] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.820347] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.820885] usb usb4: Product: UHCI Host Controller [ 7.821218] usb usb4: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.821614] usb usb4: SerialNumber: 0000:00:1a.1 [ 7.822074] usb usb4: usb_probe_device [ 7.822366] usb usb4: configuration #1 chosen from 1 choice [ 7.822730] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 7.823163] hub 4-0:1.0: usb_probe_interface [ 7.823473] hub 4-0:1.0: usb_probe_interface - got id [ 7.823811] hub 4-0:1.0: USB hub found [ 7.824111] hub 4-0:1.0: 2 ports detected [ 7.824411] hub 4-0:1.0: standalone hub [ 7.824705] hub 4-0:1.0: no power switching (usb 1.0) [ 7.825046] hub 4-0:1.0: individual port over-current protection [ 7.825420] hub 4-0:1.0: power on to power good time: 2ms [ 7.825777] hub 4-0:1.0: local power source is good [ 7.826113] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 7.826541] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.827004] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 7.827433] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 7.827858] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 7.828228] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 7.828579] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '005' [ 7.828996] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 7.829550] uhci_hcd 0000:00:1a.2: detected 2 ports [ 7.829889] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.830290] uhci_hcd 0000:00:1a.2: Performing full reset [ 7.830651] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 7.831038] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 7.831444] usb usb5: default language 0x0409 [ 7.831765] usb usb5: udev 1, busnum 5, minor = 512 [ 7.832103] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.832507] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.833049] usb usb5: Product: UHCI Host Controller [ 7.833383] usb usb5: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.833780] usb usb5: SerialNumber: 0000:00:1a.2 [ 7.834239] usb usb5: usb_probe_device [ 7.834531] usb usb5: configuration #1 chosen from 1 choice [ 7.834899] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 7.835328] hub 5-0:1.0: usb_probe_interface [ 7.835638] hub 5-0:1.0: usb_probe_interface - got id [ 7.835980] hub 5-0:1.0: USB hub found [ 7.836275] hub 5-0:1.0: 2 ports detected [ 7.836575] hub 5-0:1.0: standalone hub [ 7.836872] hub 5-0:1.0: no power switching (usb 1.0) [ 7.837211] hub 5-0:1.0: individual port over-current protection [ 7.837584] hub 5-0:1.0: power on to power good time: 2ms [ 7.837942] hub 5-0:1.0: local power source is good [ 7.838274] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 7.838701] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.839165] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 7.839596] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 7.840020] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 7.840390] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 7.840740] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '006' [ 7.841157] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 7.841704] uhci_hcd 0000:00:1d.0: detected 2 ports [ 7.842042] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.842441] uhci_hcd 0000:00:1d.0: Performing full reset [ 7.842800] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 7.843175] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 7.843575] usb usb6: default language 0x0409 [ 7.843900] usb usb6: udev 1, busnum 6, minor = 640 [ 7.844233] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.844637] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.845177] usb usb6: Product: UHCI Host Controller [ 7.845511] usb usb6: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.845910] usb usb6: SerialNumber: 0000:00:1d.0 [ 7.846382] usb usb6: usb_probe_device [ 7.846675] usb usb6: configuration #1 chosen from 1 choice [ 7.847045] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 7.847471] hub 6-0:1.0: usb_probe_interface [ 7.847782] hub 6-0:1.0: usb_probe_interface - got id [ 7.848125] hub 6-0:1.0: USB hub found [ 7.848419] hub 6-0:1.0: 2 ports detected [ 7.848719] hub 6-0:1.0: standalone hub [ 7.849015] hub 6-0:1.0: no power switching (usb 1.0) [ 7.849354] hub 6-0:1.0: individual port over-current protection [ 7.849728] hub 6-0:1.0: power on to power good time: 2ms [ 7.850088] hub 6-0:1.0: local power source is good [ 7.850421] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 7.850854] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.851320] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 7.851738] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 7.852163] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 7.852533] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 7.852885] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '007' [ 7.853300] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 7.856826] uhci_hcd 0000:00:1d.1: detected 2 ports [ 7.857163] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.857562] uhci_hcd 0000:00:1d.1: Performing full reset [ 7.857925] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 7.858293] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 7.858693] usb usb7: default language 0x0409 [ 7.859019] usb usb7: udev 1, busnum 7, minor = 768 [ 7.859352] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.859755] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.860294] usb usb7: Product: UHCI Host Controller [ 7.860627] usb usb7: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.861026] usb usb7: SerialNumber: 0000:00:1d.1 [ 7.861483] usb usb7: usb_probe_device [ 7.861774] usb usb7: configuration #1 chosen from 1 choice [ 7.862143] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 7.862568] hub 7-0:1.0: usb_probe_interface [ 7.862883] hub 7-0:1.0: usb_probe_interface - got id [ 7.863221] hub 7-0:1.0: USB hub found [ 7.863515] hub 7-0:1.0: 2 ports detected [ 7.863814] hub 7-0:1.0: standalone hub [ 7.864111] hub 7-0:1.0: no power switching (usb 1.0) [ 7.864449] hub 7-0:1.0: individual port over-current protection [ 7.864823] hub 7-0:1.0: power on to power good time: 2ms [ 7.865182] hub 7-0:1.0: local power source is good [ 7.865515] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 7.865947] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.866413] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 7.866831] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 7.867257] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 7.867626] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 7.867978] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '008' [ 7.868392] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 7.868966] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 7.869563] hub 1-0:1.0: port 1: status 0501 change 0001 [ 7.869925] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 7.869942] uhci_hcd 0000:00:1d.2: detected 2 ports [ 7.869948] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.869949] uhci_hcd 0000:00:1d.2: Performing full reset [ 7.869963] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 7.869971] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 7.870023] usb usb8: default language 0x0409 [ 7.870036] usb usb8: udev 1, busnum 8, minor = 896 [ 7.870038] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.870040] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.870043] usb usb8: Product: UHCI Host Controller [ 7.870045] usb usb8: Manufacturer: Linux 3.0.0-next-20110802+ uhci_hcd [ 7.870047] usb usb8: SerialNumber: 0000:00:1d.2 [ 7.870207] usb usb8: usb_probe_device [ 7.870209] usb usb8: configuration #1 chosen from 1 choice [ 7.870222] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 7.870307] hub 8-0:1.0: usb_probe_interface [ 7.870308] hub 8-0:1.0: usb_probe_interface - got id [ 7.870310] hub 8-0:1.0: USB hub found [ 7.870319] hub 8-0:1.0: 2 ports detected [ 7.870321] hub 8-0:1.0: standalone hub [ 7.870322] hub 8-0:1.0: no power switching (usb 1.0) [ 7.870324] hub 8-0:1.0: individual port over-current protection [ 7.870327] hub 8-0:1.0: power on to power good time: 2ms [ 7.870335] hub 8-0:1.0: local power source is good [ 7.870337] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 7.870371] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '001' [ 7.870453] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 7.870577] Initializing USB Mass Storage driver... [ 7.870664] usbcore: registered new interface driver usb-storage [ 7.870665] USB Mass Storage support registered. [ 7.870778] usbcore: registered new interface driver libusual [ 7.870862] usbcore: registered new interface driver ums-alauda [ 7.870930] usbcore: registered new interface driver ums-cypress [ 7.870993] usbcore: registered new interface driver ums-datafab [ 7.871058] usbcore: registered new interface driver ums-freecom [ 7.871125] usbcore: registered new interface driver ums-isd200 [ 7.871192] usbcore: registered new interface driver ums-jumpshot [ 7.871263] usbcore: registered new interface driver ums-karma [ 7.871329] usbcore: registered new interface driver ums-onetouch [ 7.871396] usbcore: registered new interface driver ums-sddr09 [ 7.871462] usbcore: registered new interface driver ums-sddr55 [ 7.871531] usbcore: registered new interface driver ums-usbat [ 7.871673] usbcore: registered new interface driver usbserial [ 7.871735] USB Serial support registered for generic [ 7.871807] usbcore: registered new interface driver usbserial_generic [ 7.871809] usbserial: USB Serial Driver core [ 7.871871] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 7.871946] usbcore: registered new interface driver belkin [ 7.871948] belkin_sa: v1.3:USB Belkin Serial converter driver [ 7.872010] USB Serial support registered for MCT U232 [ 7.872077] usbcore: registered new interface driver mct_u232 [ 7.872079] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver [ 7.872314] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 7.875510] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 7.875526] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 7.875879] mousedev: PS/2 mouse device common for all mice [ 7.876504] rtc_cmos 00:02: RTC can wake from S4 [ 7.876735] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 7.876773] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 7.876827] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 7.877012] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 7.877142] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 7.877146] iTCO_vendor_support: vendor-support=0 [ 7.877148] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 7.877157] md: linear personality registered for level -1 [ 7.877158] md: raid0 personality registered for level 0 [ 7.877160] md: raid1 personality registered for level 1 [ 7.877161] md: raid10 personality registered for level 10 [ 7.877163] md: raid6 personality registered for level 6 [ 7.877164] md: raid5 personality registered for level 5 [ 7.877165] md: raid4 personality registered for level 4 [ 7.877167] md: multipath personality registered for level -4 [ 7.877168] md: faulty personality registered for level -5 [ 7.877442] device-mapper: uevent: version 1.0.3 [ 7.877697] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com [ 7.877823] device-mapper: multipath: version 1.3.0 loaded [ 7.877834] device-mapper: multipath round-robin: version 1.0.0 loaded [ 7.877836] device-mapper: multipath queue-length: version 0.1.0 loaded [ 7.877837] device-mapper: multipath service-time: version 0.2.0 loaded [ 7.878029] device-mapper: dm-log-userspace: version 1.1.0 loaded [ 7.879295] cpuidle: using governor ladder [ 7.900262] hub 1-0:1.0: port 2: status 0501 change 0001 [ 7.900625] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0 ACK POWER sig=j CSC CONNECT [ 7.901227] hub 1-0:1.0: port 4: status 0501 change 0001 [ 7.901624] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 7.902757] cpuidle: using governor menu [ 7.903272] usbcore: registered new interface driver usbhid [ 7.903636] usbhid: USB HID core driver [ 7.904297] dell_wmi: No known WMI GUID found [ 7.904617] acer_wmi: Acer Laptop ACPI-WMI Extras [ 7.904961] acer_wmi: No or unsupported WMI interface, unable to load [ 7.905734] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0) [ 7.906323] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 7.906936] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 7.907330] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 7.907719] ALSA hda_intel.c:2598 chipset global capabilities = 0x4401 [ 7.908143] ALSA hda_intel.c:1091 Clearing TCSEL [ 7.912894] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 7.913304] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 7.915940] ALSA hda_intel.c:945 codec_mask = 0x4 [ 7.916422] ALSA hda_intel.c:1392 codec #2 probed OK [ 7.922011] ALSA hda_codec.c:3955 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 7.922633] hda_codec: ALC889: SKU not ready 0x411111f0 [ 7.923144] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 7.925875] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00 [ 7.926495] ALSA hda_codec.c:2339 Cannot find slave Side Playback Volume, skipped [ 7.927059] ALSA hda_codec.c:2339 Cannot find slave Headphone Playback Volume, skipped [ 7.927626] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Volume, skipped [ 7.928186] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Volume, skipped [ 7.928754] ALSA hda_codec.c:2339 Cannot find slave Side Playback Switch, skipped [ 7.929316] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Switch, skipped [ 7.929877] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Switch, skipped [ 7.931138] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 7.932181] ALSA device list: [ 7.932449] #0: HDA Intel at 0xf7f00000 irq 45 [ 7.932777] oprofile: using NMI interrupt. [ 7.933141] netem: version 1.3 [ 7.933412] Netfilter messages via NETLINK v0.30. [ 7.933771] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 7.934894] ctnetlink v0.93: registering with nfnetlink. [ 7.935281] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 7.935694] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 7.936394] xt_time: kernel timezone is -0000 [ 7.939728] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.941032] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.941452] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 7.941911] arp_tables: (C) 2002 David S. Miller [ 7.942263] TCP bic registered [ 7.942533] TCP cubic registered [ 7.942807] TCP westwood registered [ 7.943146] TCP highspeed registered [ 7.943434] TCP hybla registered [ 7.943707] TCP htcp registered [ 7.944035] TCP vegas registered [ 7.944309] TCP veno registered [ 7.944579] TCP scalable registered [ 7.944918] TCP lp registered [ 7.945184] TCP yeah registered [ 7.945455] TCP illinois registered [ 7.945738] Initializing XFRM netlink socket [ 7.946749] NET: Registered protocol family 10 [ 7.949960] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.950319] IPv6 over IPv4 tunneling driver [ 7.952227] NET: Registered protocol family 17 [ 7.952557] NET: Registered protocol family 15 [ 7.953110] Bridge firewalling registered [ 7.953425] Ebtables v2.0 registered [ 7.953794] [ 7.953794] printing PIC contents [ 7.954333] ... PIC IMR: ffff [ 7.954600] ... PIC IRR: 0c21 [ 7.954924] ... PIC ISR: 0000 [ 7.955195] ... PIC ELCR: 0c20 [ 7.955462] printing local APIC contents on CPU#0/0: [ 7.955796] ... APIC ID: 00000000 (0) [ 7.956099] ... APIC VERSION: 00060015 [ 7.956388] ... APIC TASKPRI: 00000000 (00) [ 7.956694] ... APIC PROCPRI: 00000000 [ 7.956984] ... APIC LDR: 01000000 [ 7.957260] ... APIC DFR: ffffffff [ 7.957536] ... APIC SPIV: 000001ff [ 7.957815] ... APIC ISR field: [ 7.958082] 0000000000000000000000000000000000000000000000000000000000000000 [ 7.958766] ... APIC TMR field: [ 7.959033] 0000000000000000000000000000000000020000000000000000000000000000 [ 7.959720] ... APIC IRR field: [ 7.959988] 0000000000030000000000000000000000000200000000000000000000008000 [ 7.960673] ... APIC ESR: 00000000 [ 7.960949] ... APIC ICR: 000000ef [ 7.961225] ... APIC ICR2: 03000000 [ 7.961505] ... APIC LVTT: 000000ef [ 7.961784] ... APIC LVTPC: 00000400 [ 7.962067] ... APIC LVT0: 00010700 [ 7.962347] ... APIC LVT1: 00000400 [ 7.962626] ... APIC LVTERR: 000000fe [ 7.962912] ... APIC TMICT: 00001fc2 [ 7.963194] ... APIC TMCCT: 00000000 [ 7.963476] ... APIC TDCR: 00000003 [ 7.963755] [ 7.964041] number of MP IRQ sources: 15. [ 7.964346] number of IO-APIC #8 registers: 24. [ 7.964668] testing the IO APIC....................... [ 7.965068] [ 7.965278] IO APIC #8...... [ 7.965539] .... register #00: 08000000 [ 7.965835] ....... : physical APIC id: 08 [ 7.966257] ....... : Delivery Type: 0 [ 7.966343] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.967018] ....... : LTS : 0 [ 7.967321] .... register #01: 00170020 [ 7.967618] ....... : max redirection entries: 17 [ 7.968009] ....... : PRQ implemented: 0 [ 7.968322] ....... : IO APIC version: 20 [ 7.968638] .... IRQ redirection table: [ 7.968986] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 7.969347] 00 00 1 0 0 0 0 0 0 00 [ 7.969736] 01 00 0 0 0 0 0 0 0 31 [ 7.970229] 02 00 [ 7.970238] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.970855] 0 0 0 0 0 0 0 30 [ 7.971280] 03 00 0 0 0 0 0 0 0 33 [ 7.971670] 04 00 0 0 0 0 0 0 0 34 [ 7.972109] 05 00 0 0 0 0 0 0 0 35 [ 7.972499] 06 00 1 0 0 0 0 0 0 36 [ 7.972936] 07 00 0 0 0 0 0 0 0 37 [ 7.973325] 08 00 0 0 0 0 0 0 0 38 [ 7.973712] 09 00 0 1 0 0 0 0 0 39 [ 7.974151] 0a 00 0 0 0 0 0 0 0 3A [ 7.974541] 0b 00 0 0 0 0 0 0 0 3B [ 7.974978] 0c 00 0 0 0 0 0 0 0 3C [ 7.975369] 0d 00 0 0 0 0 0 0 0 3D [ 7.975757] 0e 00 0 0 0 0 0 0 0 3E [ 7.976195] 0f 00 0 0 0 0 0 0 0 3F [ 7.976583] 10 00 0 1 0 1 0 0 0 29 [ 7.977024] 11 00 1 1 0 1 0 0 0 41 [ 7.977414] 12 00 0 1 0 1 0 0 0 91 [ 7.977801] 13 00 0 1 0 1 0 0 0 61 [ 7.978243] 14 00 1 1 0 1 0 0 0 71 [ 7.978631] 15 00 0 1 0 1 0 0 0 A1 [ 7.979072] 16 00 1 1 0 1 0 0 0 A9 [ 7.979460] 17 00 0 1 0 1 0 0 0 99 [ 7.979845] IRQ to pin mappings: [ 7.980167] IRQ0 -> 0:2 [ 7.980482] IRQ1 -> 0:1 [ 7.980799] IRQ3 -> 0:3 [ 7.981168] IRQ4 -> 0:4 [ 7.981485] IRQ5 -> 0:5 [ 7.981802] IRQ6 -> 0:6 [ 7.982168] IRQ7 -> 0:7 [ 7.982485] IRQ8 -> 0:8 [ 7.982802] IRQ9 -> 0:9 [ 7.983169] IRQ10 -> 0:10 [ 7.983493] IRQ11 -> 0:11 [ 7.983816] IRQ12 -> 0:12 [ 7.984190] IRQ13 -> 0:13 [ 7.984514] IRQ14 -> 0:14 [ 7.984837] IRQ15 -> 0:15 [ 7.985215] IRQ16 -> 0:16 [ 7.985539] IRQ17 -> 0:17 [ 7.985915] IRQ18 -> 0:18 [ 7.986240] IRQ19 -> 0:19 [ 7.986563] IRQ20 -> 0:20 [ 7.986937] IRQ21 -> 0:21 [ 7.987263] IRQ22 -> 0:22 [ 7.987586] IRQ23 -> 0:23 [ 7.987962] .................................... done. [ 7.988647] PM: Hibernation image not present or could not be loaded. [ 7.989074] registered taskstats version 1 [ 7.990102] Magic number: 7:155:87 [ 7.990481] button LNXPWRBN:00: hash matches [ 7.991013] rtc_cmos 00:02: setting system clock to 2011-08-11 17:04:50 UTC (1313082290) [ 8.000957] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000 [ 8.001330] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 8.006964] IP-Config: Complete: [ 8.007240] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 8.007783] host=fat, domain=, nis-domain=(none), [ 8.008178] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 8.052149] ehci_hcd 0000:00:1a.7: port 1 high speed [ 8.052490] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 8.103937] usb 1-1: new high speed USB device number 2 using ehci_hcd [ 8.157152] ehci_hcd 0000:00:1a.7: port 1 high speed [ 8.157489] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 8.212649] md: Waiting for all devices to be available before autodetect [ 8.213068] md: If you don't use raid, use raid=noautodetect [ 8.227671] usb 1-1: default language 0x0409 [ 8.234423] usb 1-1: udev 2, busnum 1, minor = 1 [ 8.234748] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 8.235164] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.235579] usb 1-1: Product: AX88178 [ 8.235887] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 8.236220] usb 1-1: SerialNumber: 000013 [ 8.236695] usb 1-1: usb_probe_device [ 8.237010] usb 1-1: configuration #1 chosen from 1 choice [ 8.238117] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 8.239255] asix 1-1:1.0: usb_probe_interface [ 8.239573] asix 1-1:1.0: usb_probe_interface - got id [ 8.951975] usb usb8: suspend_rh (auto-stop) [ 8.952063] usb usb5: suspend_rh (auto-stop) [ 8.952089] usb usb6: suspend_rh (auto-stop) [ 8.952112] usb usb7: suspend_rh (auto-stop) [ 8.952135] usb usb3: suspend_rh (auto-stop) [ 8.952166] usb usb4: suspend_rh (auto-stop) [ 8.954119] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 8.954851] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '002' [ 8.955452] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 8.955977] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 8.956359] md: Autodetecting RAID arrays. [ 8.956362] md: Scanned 0 and added 0 devices. [ 8.956364] md: autorun ... [ 8.956366] md: ... autorun DONE. [ 8.957752] usb usb3: wakeup_rh (auto-start) [ 8.965041] VFS: Mounted root (nfs filesystem) on device 0:16. [ 8.965467] debug: unmapping init memory ffffffff81efa000..ffffffff821aa000 [ 9.009924] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 9.010602] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s [ 9.059346] stty used greatest stack depth: 4624 bytes left [ 9.062185] ehci_hcd 0000:00:1a.7: port 4 high speed [ 9.062193] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.091788] uname used greatest stack depth: 3872 bytes left [ 9.098439] sed used greatest stack depth: 3728 bytes left [ 9.113015] usb 1-4: new high speed USB device number 4 using ehci_hcd [ 9.132179] sh used greatest stack depth: 3696 bytes left [ 9.153380] mountpoint used greatest stack depth: 3616 bytes left [ 9.164191] ehci_hcd 0000:00:1a.7: port 4 high speed [ 9.164564] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.575180] amixer used greatest stack depth: 3552 bytes left [ 10.166571] usb 1-4: default language 0x0409 [ 10.168320] usb 1-4: udev 4, busnum 1, minor = 3 [ 10.168667] usb 1-4: New USB device found, idVendor=1307, idProduct=0165 [ 10.169103] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.169590] usb 1-4: Product: USB Mass Storage Device [ 10.170025] usb 1-4: Manufacturer: Teclast Technology [ 10.170414] usb 1-4: SerialNumber: 0000000000020D [ 10.170953] usb 1-4: usb_probe_device [ 10.171293] usb 1-4: configuration #1 chosen from 1 choice [ 10.171753] usb 1-4: adding 1-4:1.0 (config #1, interface 0) [ 10.172253] usb-storage 1-4:1.0: usb_probe_interface [ 10.172596] usb-storage 1-4:1.0: usb_probe_interface - got id [ 10.173234] scsi9 : usb-storage 1-4:1.0 [ 10.173794] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '004' [ 10.174310] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 10.174671] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 10.175034] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 10.282011] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 10.383988] usb 3-2: new low speed USB device number 2 using uhci_hcd [ 10.581229] usb 3-2: skipped 1 descriptor after interface [ 10.581615] usb 3-2: skipped 1 descriptor after interface [ 10.588218] usb 3-2: default language 0x0409 [ 10.619180] usb 3-2: udev 2, busnum 3, minor = 257 [ 10.619551] usb 3-2: New USB device found, idVendor=0557, idProduct=2220 [ 10.620014] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 10.620455] usb 3-2: Product: ATEN CS-1758/54 [ 10.620788] usb 3-2: Manufacturer: ATEN [ 10.621421] usb 3-2: usb_probe_device [ 10.621755] usb 3-2: configuration #1 chosen from 1 choice [ 10.625248] usb 3-2: adding 3-2:1.0 (config #1, interface 0) [ 10.665337] usbserial_generic 3-2:1.0: usb_probe_interface [ 10.665847] usbserial_generic 3-2:1.0: usb_probe_interface - got id [ 10.666344] usbhid 3-2:1.0: usb_probe_interface [ 10.666689] usbhid 3-2:1.0: usb_probe_interface - got id [ 10.698928] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input4 [ 10.699721] uhci_hcd 0000:00:1a.0: reserve dev 2 ep81-INT, period 8, phase 4, 118 us [ 10.700595] generic-usb 0003:0557:2220.0001: input: USB HID v1.10 Keyboard [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input0 [ 10.701440] usb 3-2: adding 3-2:1.1 (config #1, interface 1) [ 10.711282] usbserial_generic 3-2:1.1: usb_probe_interface [ 10.711669] usbserial_generic 3-2:1.1: usb_probe_interface - got id [ 10.712188] usbhid 3-2:1.1: usb_probe_interface [ 10.712192] usbhid 3-2:1.1: usb_probe_interface - got id [ 10.739551] input: ATEN ATEN CS-1758/54 as /devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.1/input/input5 [ 10.740618] generic-usb 0003:0557:2220.0002: input: USB HID v1.10 Mouse [ATEN ATEN CS-1758/54] on usb-0000:00:1a.0-2/input1 [ 10.741498] /c/wfg/linux-next/drivers/usb/core/inode.c: creating file '002' [ 10.742100] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 10.742518] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 10.742922] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 10.936422] EXT4-fs (sda5): recovery complete [ 10.936815] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 11.174499] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 11.289829] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 11.291081] sd 9:0:0:0: [sdb] Write Protect is off [ 11.291428] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 11.292450] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.292841] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.297681] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.298070] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.432422] sdb: sdb1 sdb2 sdb3 [ 11.435921] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.436305] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.436685] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 11.617573] svc: failed to register lockdv1 RPC service (errno 97). [ 11.620427] mount.nfs used greatest stack depth: 3104 bytes left [ 14.494938] XFS (sda7): Mounting Filesystem [ 14.558275] XFS (sda7): Ending clean mount [ 18.650283] eth0: no IPv6 routers present