[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 3.1.0-rc1-no-maxpause+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #198 SMP Tue Aug 16 08:31:11 CST 2011 [ 0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1-no-maxpause+ [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcda4000 (usable) [ 0.000000] BIOS-e820: 00000000bcda4000 - 00000000bcfdd000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcfdd000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf800000 [ 0.000000] 0000000000 - 00bf800000 page 4k [ 0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000 [ 0.000000] log_buf_len: 8388608 [ 0.000000] early log buf free: 258293(98%) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-00000000bf800000 [ 0.000000] Initmem setup node 0 0000000000000000-00000000bf800000 [ 0.000000] NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff] [ 0.000000] [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800b9c00000-ffff8800bc5fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x000bcda4 [ 0.000000] 0: 0x000bcfdd -> 0x000bf6bd [ 0.000000] 0: 0x000bf6bf -> 0x000bf714 [ 0.000000] 0: 0x000bf7bf -> 0x000bf7e7 [ 0.000000] 0: 0x000bf7ff -> 0x000bf800 [ 0.000000] On node 0 totalpages: 783502 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3919 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 10668 pages used for memmap [ 0.000000] DMA32 zone: 768854 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bcda4000 - 00000000bcfdd000 [ 0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915008 r8192 d22400 u2097152 [ 0.000000] pcpu-alloc: s1915008 r8192 d22400 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 772773 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1-no-maxpause+ [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Memory: 3019044k/3137536k available (9445k kernel code, 3528k absent, 114964k reserved, 5641k data, 2768k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] NR_IRQS:4352 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6335 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 25165824 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.001000] Fast TSC calibration using PIT [ 0.002000] Detected 3200.557 MHz processor. [ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6401.11 BogoMIPS (lpj=3200557) [ 0.000708] pid_max: default: 32768 minimum: 301 [ 0.001927] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.004003] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.005010] Mount-cache hash table entries: 256 [ 0.005730] Initializing cgroup subsys debug [ 0.006039] Initializing cgroup subsys cpuacct [ 0.006371] Initializing cgroup subsys memory [ 0.006710] Initializing cgroup subsys devices [ 0.007025] Initializing cgroup subsys freezer [ 0.007350] Initializing cgroup subsys blkio [ 0.007714] CPU: Physical Processor ID: 0 [ 0.008012] CPU: Processor Core ID: 0 [ 0.008309] mce: CPU supports 9 MCE banks [ 0.008614] CPU0: Thermal monitoring enabled (TM1) [ 0.008951] using mwait in idle threads. [ 0.010099] ACPI: Core revision 20110623 [ 0.022079] ftrace: allocating 36036 entries in 142 pages [ 0.030562] Getting VERSION: 60015 [ 0.030838] Getting VERSION: 60015 [ 0.031124] Getting ID: 0 [ 0.031370] Getting ID: 0 [ 0.031616] Switched APIC routing to physical flat. [ 0.031946] enabled ExtINT on CPU#0 [ 0.032390] ENABLING IO-APIC IRQs [ 0.032660] init IO_APIC IRQs [ 0.032919] apic 8 pin 0 not connected [ 0.033224] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0) [ 0.033786] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0) [ 0.034360] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) [ 0.034925] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0) [ 0.035491] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0) [ 0.036054] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0) [ 0.036619] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0) [ 0.037186] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 0.037749] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0) [ 0.038315] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0) [ 0.038886] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0) [ 0.039459] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0) [ 0.040029] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 0.040601] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0) [ 0.041172] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0) [ 0.041740] apic 8 pin 16 not connected [ 0.042033] apic 8 pin 17 not connected [ 0.042329] apic 8 pin 18 not connected [ 0.042623] apic 8 pin 19 not connected [ 0.042917] apic 8 pin 20 not connected [ 0.043213] apic 8 pin 21 not connected [ 0.043506] apic 8 pin 22 not connected [ 0.043799] apic 8 pin 23 not connected [ 0.044230] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.054572] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.055055] Using local APIC timer interrupts. [ 0.055055] calibrating APIC timer ... [ 0.156667] ... lapic delta = 833229 [ 0.156949] ... PM-Timer delta = 357897 [ 0.157239] ... PM-Timer result ok [ 0.157514] ..... delta 833229 [ 0.157776] ..... mult: 35792353 [ 0.158044] ..... calibration result: 133316 [ 0.158350] ..... CPU clock speed is 3199.0598 MHz. [ 0.158678] ..... host bus clock speed is 133.0316 MHz. [ 0.159033] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver. [ 0.159792] ... version: 3 [ 0.160092] ... bit width: 48 [ 0.160393] ... generic registers: 4 [ 0.160690] ... value mask: 0000ffffffffffff [ 0.161036] ... max period: 000000007fffffff [ 0.161381] ... fixed-purpose events: 3 [ 0.161678] ... event mask: 000000070000000f [ 0.162416] lockdep: fixing up alternatives. [ 0.162787] Booting Node 0, Processors #1 [ 0.163007] smpboot cpu 1: start_ip = 97000 [ 2.414616] masked ExtINT on CPU#1 [ 2.494424] lockdep: fixing up alternatives. [ 2.494758] #2 [ 2.494850] smpboot cpu 2: start_ip = 97000 [ 2.506292] masked ExtINT on CPU#2 [ 2.586091] lockdep: fixing up alternatives. [ 2.586426] #3 [ 2.586518] smpboot cpu 3: start_ip = 97000 [ 2.598057] masked ExtINT on CPU#3 [ 2.677751] lockdep: fixing up alternatives. [ 2.678088] #4 [ 2.678180] smpboot cpu 4: start_ip = 97000 [ 2.689718] masked ExtINT on CPU#4 [ 2.769386] lockdep: fixing up alternatives. [ 2.769722] #5 [ 2.769815] smpboot cpu 5: start_ip = 97000 [ 2.781353] masked ExtINT on CPU#5 [ 2.861164] lockdep: fixing up alternatives. [ 2.861502] #6 [ 2.861594] smpboot cpu 6: start_ip = 97000 [ 2.876088] masked ExtINT on CPU#6 [ 2.955796] lockdep: fixing up alternatives. [ 2.956131] #7 [ 2.956224] smpboot cpu 7: start_ip = 97000 [ 2.967760] masked ExtINT on CPU#7 [ 3.047265] Brought up 8 CPUs [ 3.047526] Total of 8 processors activated (51188.83 BogoMIPS). [ 3.051260] CPU0 attaching sched-domain: [ 3.051557] domain 0: span 0,4 level SIBLING [ 3.051901] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 3.052435] domain 1: span 0-7 level MC [ 3.052765] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 3.053718] CPU1 attaching sched-domain: [ 3.054012] domain 0: span 1,5 level SIBLING [ 3.054358] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 3.054887] domain 1: span 0-7 level MC [ 3.055221] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 3.056173] CPU2 attaching sched-domain: [ 3.056468] domain 0: span 2,6 level SIBLING [ 3.056811] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 3.057343] domain 1: span 0-7 level MC [ 3.057672] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 3.058624] CPU3 attaching sched-domain: [ 3.058918] domain 0: span 3,7 level SIBLING [ 3.059264] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 3.059793] domain 1: span 0-7 level MC [ 3.060126] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 3.061076] CPU4 attaching sched-domain: [ 3.061373] domain 0: span 0,4 level SIBLING [ 3.061716] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 3.062247] domain 1: span 0-7 level MC [ 3.062577] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 3.063529] CPU5 attaching sched-domain: [ 3.063823] domain 0: span 1,5 level SIBLING [ 3.064169] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 3.064697] domain 1: span 0-7 level MC [ 3.065029] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 3.065981] CPU6 attaching sched-domain: [ 3.066279] domain 0: span 2,6 level SIBLING [ 3.066621] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 3.067153] domain 1: span 0-7 level MC [ 3.067483] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 3.068437] CPU7 attaching sched-domain: [ 3.068731] domain 0: span 3,7 level SIBLING [ 3.069073] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 3.069604] domain 1: span 0-7 level MC [ 3.069934] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 3.071388] kworker/u:0 used greatest stack depth: 5288 bytes left [ 3.073662] PM: Registering ACPI NVS region at bcda4000 (2330624 bytes) [ 3.074160] PM: Registering ACPI NVS region at bf714000 (700416 bytes) [ 3.075274] xor: automatically using best checksumming function: generic_sse [ 3.080058] generic_sse: 11924.000 MB/sec [ 3.080367] xor: using function: generic_sse (11924.000 MB/sec) [ 3.080815] RTC time: 22:02:17, date: 08/17/11 [ 3.081252] NET: Registered protocol family 16 [ 3.082257] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 3.082807] ACPI: bus type pci registered [ 3.083302] dca service started, version 1.12.1 [ 3.083698] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 3.084314] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 3.097853] PCI: Using configuration type 1 for base access [ 3.120210] bio: create slab at 0 [ 3.136874] raid6: int64x1 3171 MB/s [ 3.153815] raid6: int64x2 3402 MB/s [ 3.170751] raid6: int64x4 2738 MB/s [ 3.187712] raid6: int64x8 2101 MB/s [ 3.204640] raid6: sse2x1 7921 MB/s [ 3.221575] raid6: sse2x2 9269 MB/s [ 3.238518] raid6: sse2x4 10292 MB/s [ 3.238807] raid6: using algorithm sse2x4 (10292 MB/s) [ 3.239231] ACPI: Added _OSI(Module Device) [ 3.239541] ACPI: Added _OSI(Processor Device) [ 3.239856] ACPI: Added _OSI(3.0 _SCP Extensions) [ 3.240179] ACPI: Added _OSI(Processor Aggregator Device) [ 3.244482] ACPI: EC: Look up EC in DSDT [ 3.266634] ACPI: Interpreter enabled [ 3.266921] ACPI: (supports S0 S1 S3 S4 S5) [ 3.267432] ACPI: Using IOAPIC for interrupt routing [ 3.280343] ACPI: No dock devices found. [ 3.280646] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 3.281875] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 3.283552] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 3.283947] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 3.284340] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 3.284879] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 3.285420] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 3.285956] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 3.286519] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 3.286955] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 3.287385] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 3.287763] pci 0000:00:01.0: PME# disabled [ 3.288093] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 3.288522] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 3.288899] pci 0000:00:03.0: PME# disabled [ 3.289228] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 3.289656] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 3.290031] pci 0000:00:07.0: PME# disabled [ 3.290367] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 3.290811] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 3.291257] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 3.291707] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 3.292151] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 3.292594] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 3.293043] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 3.293435] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 3.293819] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 3.294203] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 3.294614] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 3.294992] pci 0000:00:19.0: PME# disabled [ 3.295315] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 3.295743] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 3.296148] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 3.296572] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 3.296975] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 3.297400] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 3.297814] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 3.298203] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 3.298665] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 3.299043] pci 0000:00:1a.7: PME# disabled [ 3.299377] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 3.299762] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 3.300224] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 3.300605] pci 0000:00:1b.0: PME# disabled [ 3.300931] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 3.301372] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 3.301749] pci 0000:00:1c.0: PME# disabled [ 3.302075] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 3.302514] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 3.302891] pci 0000:00:1c.1: PME# disabled [ 3.303222] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 3.303663] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 3.304039] pci 0000:00:1c.4: PME# disabled [ 3.304373] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 3.304793] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 3.305197] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 3.305621] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 3.306023] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 3.306445] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 3.306859] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 3.307248] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 3.307710] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 3.308087] pci 0000:00:1d.7: PME# disabled [ 3.308414] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 3.308855] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 3.309326] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 3.309708] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 3.310256] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 3.310852] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 3.311242] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 3.311604] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 3.311961] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 3.312322] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 3.312680] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 3.313038] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 3.313454] pci 0000:00:1f.2: PME# supported from D3hot [ 3.313799] pci 0000:00:1f.2: PME# disabled [ 3.314123] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 3.314513] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 3.314933] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 3.315361] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 3.315766] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 3.316145] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 3.316531] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 3.316959] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 3.317376] pci 0000:02:00.0: supports D1 D2 [ 3.320662] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 3.321041] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 3.321486] pci 0000:02:00.1: supports D1 D2 [ 3.321810] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 3.322156] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 3.322564] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 3.323159] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 3.323564] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 3.323965] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 3.324393] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 3.324783] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 3.325146] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 3.325513] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 3.325876] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 3.326242] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 3.326606] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 3.327044] pci 0000:06:00.0: supports D1 [ 3.327344] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 3.327710] pci 0000:06:00.0: PME# disabled [ 3.328033] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 3.328381] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 3.328758] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 3.329213] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 3.329601] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 3.329984] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 3.330434] pci 0000:07:03.0: supports D1 D2 [ 3.330741] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 3.331123] pci 0000:07:03.0: PME# disabled [ 3.331483] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 3.331898] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 3.332306] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 3.332863] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 3.333423] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 3.334005] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 3.334592] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 3.335175] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 3.335797] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 3.337151] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 3.337791] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 3.338269] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 3.338740] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 3.339214] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 3.339686] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 3.340171] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 3.340738] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19) [ 3.365011] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 3.366100] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 3.367187] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 3.368273] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 3.369353] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 3.370435] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 3.371516] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 3.372600] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 3.373870] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 3.374448] vgaarb: loaded [ 3.374697] vgaarb: bridge control possible 0000:02:00.0 [ 3.375349] SCSI subsystem initialized [ 3.375802] libata version 3.00 loaded. [ 3.376359] usbcore: registered new interface driver usbfs [ 3.376769] usbcore: registered new interface driver hub [ 3.377188] usbcore: registered new device driver usb [ 3.377958] wmi: Mapper loaded [ 3.378291] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 3.378676] PCI: Using ACPI for IRQ routing [ 3.380561] PCI: Discovered peer bus 3f [ 3.380932] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600 [ 3.381336] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600 [ 3.381739] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600 [ 3.382138] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600 [ 3.382540] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600 [ 3.382936] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600 [ 3.383339] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600 [ 3.383738] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600 [ 3.384143] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600 [ 3.384538] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600 [ 3.384935] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600 [ 3.385338] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600 [ 3.385735] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600 [ 3.386134] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600 [ 3.386532] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600 [ 3.386931] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600 [ 3.387333] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600 [ 3.387728] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600 [ 3.388133] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600 [ 3.389902] PCI: pci_cache_line_size set to 64 bytes [ 3.390481] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 3.390744] reserve RAM buffer: 00000000bcda4000 - 00000000bfffffff [ 3.391168] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff [ 3.391587] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff [ 3.392007] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff [ 3.392426] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff [ 3.423804] pnp: PnP ACPI init [ 3.424249] ACPI: bus type pnp registered [ 3.425205] pnp 00:00: [bus 00-3d] [ 3.425482] pnp 00:00: [io 0x0cf8-0x0cff] [ 3.425784] pnp 00:00: [io 0x0000-0x0cf7 window] [ 3.426113] pnp 00:00: [io 0x0d00-0xffff window] [ 3.426443] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 3.426793] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 3.427150] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 3.427499] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 3.427849] pnp 00:00: [mem 0x00000000 window] [ 3.428302] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 3.428986] pnp 00:01: [io 0x0000-0x000f] [ 3.429288] pnp 00:01: [io 0x0081-0x0083] [ 3.429590] pnp 00:01: [io 0x0087] [ 3.429873] pnp 00:01: [io 0x0089-0x008b] [ 3.430175] pnp 00:01: [io 0x008f] [ 3.430454] pnp 00:01: [io 0x00c0-0x00df] [ 3.430756] pnp 00:01: [dma 4] [ 3.431113] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 3.431522] pnp 00:02: [io 0x0070-0x0071] [ 3.431822] pnp 00:02: [io 0x0074-0x0077] [ 3.432133] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 3.432696] pnp 00:02: [irq 8] [ 3.433054] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 3.433466] pnp 00:03: [io 0x00f0] [ 3.433747] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 3.434319] pnp 00:03: [irq 13] [ 3.434676] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 3.435093] pnp 00:04: [io 0x0061] [ 3.435467] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 3.435883] pnp 00:05: [io 0x0500-0x053f] [ 3.436184] pnp 00:05: [io 0x0400-0x047f] [ 3.436485] pnp 00:05: [io 0x0092] [ 3.436763] pnp 00:05: [io 0x0680-0x06ff] [ 3.437068] pnp 00:05: [io 0x0010-0x001f] [ 3.437368] pnp 00:05: [io 0x0072-0x0073] [ 3.437668] pnp 00:05: [io 0x0080] [ 3.437950] pnp 00:05: [io 0x0084-0x0086] [ 3.438250] pnp 00:05: [io 0x0088] [ 3.438528] pnp 00:05: [io 0x008c-0x008e] [ 3.438829] pnp 00:05: [io 0x0090-0x009f] [ 3.439313] system 00:05: [io 0x0500-0x053f] has been reserved [ 3.439683] system 00:05: [io 0x0400-0x047f] has been reserved [ 3.440059] system 00:05: [io 0x0680-0x06ff] has been reserved [ 3.440431] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 3.440919] pnp 00:06: [io 0x0060] [ 3.441202] pnp 00:06: [io 0x0064] [ 3.441647] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 3.442606] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 3.443045] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 3.443573] pnp: PnP ACPI: found 8 devices [ 3.443881] ACPI: ACPI bus type pnp unregistered [ 3.453803] Switching to clocksource acpi_pm [ 3.454246] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 3.454842] Switched to NOHz mode on CPU #4 [ 3.454844] Switched to NOHz mode on CPU #0 [ 3.454867] Switched to NOHz mode on CPU #7 [ 3.454886] Switched to NOHz mode on CPU #6 [ 3.454888] Switched to NOHz mode on CPU #3 [ 3.454897] PCI: max bus depth: 1 pci_try_num: 2 [ 3.454909] Switched to NOHz mode on CPU #2 [ 3.454920] Switched to NOHz mode on CPU #1 [ 3.454930] Switched to NOHz mode on CPU #5 [ 3.454959] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 3.454975] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 3.454979] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 3.454983] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 3.454987] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 3.454994] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 3.455006] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 3.455023] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 3.455042] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 3.455047] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 3.455053] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 3.455066] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 3.455073] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 3.455104] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0) [ 3.455110] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.455116] pci 0000:00:01.0: setting latency timer to 64 [ 3.455125] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.455130] pci 0000:00:03.0: setting latency timer to 64 [ 3.455140] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.455146] pci 0000:00:07.0: setting latency timer to 64 [ 3.455165] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0) [ 3.455170] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.455176] pci 0000:00:1c.0: setting latency timer to 64 [ 3.455185] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 3.455191] pci 0000:00:1c.1: setting latency timer to 64 [ 3.455199] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.455204] pci 0000:00:1c.4: setting latency timer to 64 [ 3.455213] pci 0000:00:1e.0: setting latency timer to 64 [ 3.455217] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 3.455219] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 3.455221] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 3.455223] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 3.455225] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 3.455227] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 3.455229] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 3.455231] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 3.455234] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 3.455235] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 3.455238] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 3.455239] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 3.455242] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 3.455244] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 3.455246] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 3.455248] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 3.455250] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 3.455252] pci_bus 0000:3f: resource 0 [io 0x0000-0xffff] [ 3.455254] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff] [ 3.479070] NET: Registered protocol family 2 [ 3.479749] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 3.482298] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 3.486111] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) [ 3.489499] TCP: Hash tables configured (established 524288 bind 65536) [ 3.489909] TCP reno registered [ 3.490255] UDP hash table entries: 2048 (order: 6, 393216 bytes) [ 3.490882] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes) [ 3.491689] NET: Registered protocol family 1 [ 3.492297] RPC: Registered named UNIX socket transport module. [ 3.492667] RPC: Registered udp transport module. [ 3.492990] RPC: Registered tcp transport module. [ 3.493324] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.493754] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 3.494145] pci 0000:00:1a.0: Performing full reset [ 3.494498] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 3.494890] pci 0000:00:1a.1: Performing full reset [ 3.495247] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 3.495637] pci 0000:00:1a.2: Performing full reset [ 3.496135] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 3.496533] pci 0000:00:1d.0: Performing full reset [ 3.496880] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 3.497292] pci 0000:00:1d.1: Performing full reset [ 3.497642] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 3.498034] pci 0000:00:1d.2: Performing full reset [ 3.498528] pci 0000:02:00.0: Boot video device [ 3.498905] PCI: CLS 64 bytes, default 64 [ 3.503077] Machine check injector initialized [ 3.504932] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 3.505320] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 3.505693] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 3.506063] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 3.506433] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 3.506808] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 3.507182] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 3.507551] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 3.507995] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 3.509057] audit: initializing netlink socket (disabled) [ 3.509443] type=2000 audit(1313618534.169:1): initialized [ 3.539809] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 3.541760] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 3.542489] fuse init (API version 7.16) [ 3.542987] JFS: nTxBlock = 8192, nTxLock = 65536 [ 3.546468] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 3.547816] NILFS version 2 loaded [ 3.548405] Btrfs loaded [ 3.548654] msgmni has been set to 5896 [ 3.549793] async_tx: api initialized (async) [ 3.550223] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 3.550814] io scheduler noop registered [ 3.551125] io scheduler deadline registered [ 3.551487] io scheduler cfq registered (default) [ 3.552260] pcieport 0000:00:1c.0: setting latency timer to 64 [ 3.552678] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 3.553168] pcieport 0000:00:1c.1: setting latency timer to 64 [ 3.553582] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 3.554074] pcieport 0000:00:1c.4: setting latency timer to 64 [ 3.554489] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 3.555212] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 3.556041] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 3.556623] ACPI: Sleep Button [SLPB] [ 3.557062] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 3.557605] ACPI: Power Button [PWRF] [ 3.558637] ACPI: acpi_idle registered with cpuidle [ 3.559403] Monitor-Mwait will be used to enter C-1 state [ 3.559799] Monitor-Mwait will be used to enter C-3 state [ 3.567476] ioatdma: Intel(R) QuickData Technology Driver 4.00 [ 3.611686] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.633848] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 3.682901] Initializing Nozomi driver 2.1d [ 3.683713] Non-volatile memory driver v1.3 [ 3.684454] Linux agpgart interface v0.103 [ 3.684851] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 3.685449] Hangcheck: Using getrawmonotonic(). [ 3.685841] [drm] Initialized drm 1.1.0 20060810 [ 3.686163] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 4.498133] Refined TSC clocksource calibration: 3200.113 MHz. [ 4.498502] Switching to clocksource tsc [ 6.697365] floppy0: no floppy controllers found [ 6.828800] brd: module loaded [ 6.830595] loop: module loaded [ 6.831349] Loading iSCSI transport class v2.0-870. [ 6.832278] Loading Adaptec I2O RAID: Version 2.4 Build 5go [ 6.832634] Detecting Adaptec I2O RAID controllers... [ 6.833158] Adaptec aacraid driver 1.1-7[28000]-ms [ 6.834046] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 6.834665] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.03-k. [ 6.835411] iscsi: registered transport (qla4xxx) [ 6.835810] QLogic iSCSI HBA Driver [ 6.836173] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) [ 6.836780] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) [ 6.837271] megasas: 00.00.05.40-rc1 Tue. Jul. 26 17:00:00 PDT 2011 [ 6.837735] mpt2sas version 09.100.00.00 loaded [ 6.838451] ahci 0000:00:1f.2: version 3.0 [ 6.838781] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0) [ 6.839354] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 6.839805] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 6.840224] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 6.840794] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 6.841360] ahci 0000:00:1f.2: setting latency timer to 64 [ 6.852103] scsi0 : ahci [ 6.852568] scsi1 : ahci [ 6.852977] scsi2 : ahci [ 6.853373] scsi3 : ahci [ 6.853808] scsi4 : ahci [ 6.854207] scsi5 : ahci [ 6.854878] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43 [ 6.855419] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43 [ 6.855963] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 6.856504] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 6.857047] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 6.857587] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 6.858158] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.861533] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 6.862196] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 6.862601] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 6.863010] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 6.863380] ahci: SSS flag set, parallel bus scan disabled [ 6.863774] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 6.864336] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 6.864709] ahci 0000:06:00.0: setting latency timer to 64 [ 6.865942] scsi6 : ahci [ 6.866343] scsi7 : ahci [ 6.866741] scsi8 : ahci [ 6.867123] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 6.867663] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 6.868206] ata9: DUMMY [ 6.870445] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 6.870858] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 6.871300] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k [ 6.871667] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 6.872069] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0) [ 6.872637] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 6.873052] e1000e 0000:00:19.0: setting latency timer to 64 [ 6.873520] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 7.063621] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54 [ 7.064188] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 7.064624] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 7.065099] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k [ 7.065493] Copyright (c) 2007-2011 Intel Corporation. [ 7.065913] Intel(R) Virtual Function Network Driver - version 2.0.0-k [ 7.066312] Copyright (c) 2009 - 2010 Intel Corporation. [ 7.066736] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k [ 7.067289] ixgbe: Copyright (c) 1999-2011 Intel Corporation. [ 7.067727] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 7.068143] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 7.068868] jme: JMicron JMC2XX ethernet driver version 1.0.8 [ 7.069307] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI [ 7.069682] e100: Copyright(c) 1999-2006 Intel Corporation [ 7.070338] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 7.070959] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011) [ 7.071607] sky2: driver version 1.29 [ 7.072886] tun: Universal TUN/TAP device driver, 1.6 [ 7.073228] tun: (C) 1999-2004 Max Krasnyansky [ 7.073883] usbcore: registered new interface driver catc [ 7.074236] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 7.074655] usbcore: registered new interface driver kaweth [ 7.075011] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 7.075609] usbcore: registered new interface driver pegasus [ 7.075969] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 7.076424] usbcore: registered new interface driver rtl8150 [ 7.076829] usbcore: registered new interface driver asix [ 7.077227] usbcore: registered new interface driver cdc_ether [ 7.077640] usbcore: registered new interface driver cdc_eem [ 7.078047] usbcore: registered new interface driver dm9601 [ 7.078473] usbcore: registered new interface driver smsc75xx [ 7.078887] usbcore: registered new interface driver smsc95xx [ 7.079307] usbcore: registered new interface driver gl620a [ 7.079711] usbcore: registered new interface driver net1080 [ 7.080122] usbcore: registered new interface driver plusb [ 7.080524] usbcore: registered new interface driver rndis_host [ 7.080941] usbcore: registered new interface driver cdc_subset [ 7.081365] usbcore: registered new interface driver zaurus [ 7.081771] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 7.082371] usbcore: registered new interface driver int51x1 [ 7.082730] cdc_ncm: 04-Aug-2011 [ 7.083047] usbcore: registered new interface driver cdc_ncm [ 7.083411] netconsole: local port 6665 [ 7.083703] netconsole: local IP 10.0.0.0 [ 7.084000] netconsole: interface 'eth0' [ 7.084301] netconsole: remote port 6666 [ 7.084595] netconsole: remote IP 192.168.1.1 [ 7.084905] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 7.085283] netconsole: device eth0 not up yet, forcing it [ 7.161846] ata4: SATA link down (SStatus 0 SControl 300) [ 7.162224] ata5: SATA link down (SStatus 0 SControl 300) [ 7.162594] ata6: SATA link down (SStatus 0 SControl 300) [ 7.162967] ata3: SATA link down (SStatus 0 SControl 300) [ 7.163339] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 7.171818] ata7: SATA link down (SStatus 0 SControl 300) [ 7.178243] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 7.209183] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 7.209543] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 7.228680] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 7.267305] ata1.00: configured for UDMA/133 [ 7.267803] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 7.268728] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 7.269351] sd 0:0:0:0: [sda] Write Protect is off [ 7.269684] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 7.270050] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.359050] sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 > [ 7.360303] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.517840] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 7.598386] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 7.598783] ata2.00: applying bridge limits [ 7.629542] ata2.00: configured for UDMA/33 [ 7.630850] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 7.935465] ata8: SATA link down (SStatus 0 SControl 300) [ 9.939106] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 9.941595] console [netcon0] enabled [ 9.941885] netconsole: network logging started [ 9.942270] Fusion MPT base driver 3.04.19 [ 9.942575] Copyright (c) 1999-2008 LSI Corporation [ 9.942917] Fusion MPT SPI Host driver 3.04.19 [ 9.943322] Fusion MPT FC Host driver 3.04.19 [ 9.943718] Fusion MPT SAS Host driver 3.04.19 [ 9.944118] Fusion MPT misc device (ioctl) driver 3.04.19 [ 9.944545] mptctl: Registered with Fusion MPT base driver [ 9.944901] mptctl: /dev/mptctl @ (major,minor=10,220) [ 9.945345] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 9.945740] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 9.946160] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0) [ 9.946735] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 9.947163] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 9.947535] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 9.947950] /c/wfg/linux/drivers/usb/core/inode.c: creating file 'devices' [ 9.948375] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 9.948780] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 9.949332] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 9.949932] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 9.950584] ehci_hcd 0000:00:1a.7: debug port 1 [ 9.950905] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.955389] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 9.955792] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 9.956180] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 9.956543] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.961014] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 9.967132] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 9.967581] usb usb1: default language 0x0409 [ 9.967904] usb usb1: udev 1, busnum 1, minor = 0 [ 9.968235] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 9.968637] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 9.969175] usb usb1: Product: EHCI Host Controller [ 9.969507] usb usb1: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ ehci_hcd [ 9.969909] usb usb1: SerialNumber: 0000:00:1a.7 [ 9.970352] usb usb1: usb_probe_device [ 9.970645] usb usb1: configuration #1 chosen from 1 choice [ 9.971029] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 9.971478] hub 1-0:1.0: usb_probe_interface [ 9.971790] hub 1-0:1.0: usb_probe_interface - got id [ 9.972132] hub 1-0:1.0: USB hub found [ 9.972428] hub 1-0:1.0: 6 ports detected [ 9.972728] hub 1-0:1.0: standalone hub [ 9.973021] hub 1-0:1.0: no power switching (usb 1.0) [ 9.973363] hub 1-0:1.0: individual port over-current protection [ 9.973737] hub 1-0:1.0: power on to power good time: 20ms [ 9.974113] hub 1-0:1.0: local power source is good [ 9.974447] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 9.974901] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 9.975420] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0) [ 9.975991] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 9.976424] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 9.976794] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 9.977149] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002' [ 9.977547] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 9.978099] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 9.978700] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 9.982309] ehci_hcd 0000:00:1d.7: debug port 1 [ 9.982630] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.987091] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 9.987493] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 9.987878] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 9.988246] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 9.992715] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 9.999036] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 9.999444] usb usb2: default language 0x0409 [ 9.999766] usb usb2: udev 1, busnum 2, minor = 128 [ 10.000102] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.000505] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.001042] usb usb2: Product: EHCI Host Controller [ 10.001374] usb usb2: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ ehci_hcd [ 10.001775] usb usb2: SerialNumber: 0000:00:1d.7 [ 10.002221] usb usb2: usb_probe_device [ 10.002512] usb usb2: configuration #1 chosen from 1 choice [ 10.002876] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 10.003310] hub 2-0:1.0: usb_probe_interface [ 10.003619] hub 2-0:1.0: usb_probe_interface - got id [ 10.003956] hub 2-0:1.0: USB hub found [ 10.004255] hub 2-0:1.0: 6 ports detected [ 10.004555] hub 2-0:1.0: standalone hub [ 10.004847] hub 2-0:1.0: no power switching (usb 1.0) [ 10.005189] hub 2-0:1.0: individual port over-current protection [ 10.005563] hub 2-0:1.0: power on to power good time: 20ms [ 10.005923] hub 2-0:1.0: local power source is good [ 10.006257] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 10.006710] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.007262] uhci_hcd: USB Universal Host Controller Interface driver [ 10.007702] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 10.008127] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 10.008496] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 10.008846] /c/wfg/linux/drivers/usb/core/inode.c: creating file '003' [ 10.009247] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 10.009796] uhci_hcd 0000:00:1a.0: detected 2 ports [ 10.010134] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 10.010533] uhci_hcd 0000:00:1a.0: Performing full reset [ 10.010893] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 10.011264] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 10.011681] usb usb3: default language 0x0409 [ 10.012008] usb usb3: udev 1, busnum 3, minor = 256 [ 10.012340] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.012742] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.013283] usb usb3: Product: UHCI Host Controller [ 10.013616] usb usb3: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd [ 10.014023] usb usb3: SerialNumber: 0000:00:1a.0 [ 10.014479] usb usb3: usb_probe_device [ 10.014772] usb usb3: configuration #1 chosen from 1 choice [ 10.015141] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 10.015578] hub 3-0:1.0: usb_probe_interface [ 10.015889] hub 3-0:1.0: usb_probe_interface - got id [ 10.016232] hub 3-0:1.0: USB hub found [ 10.016528] hub 3-0:1.0: 2 ports detected [ 10.016828] hub 3-0:1.0: standalone hub [ 10.017125] hub 3-0:1.0: no power switching (usb 1.0) [ 10.017465] hub 3-0:1.0: individual port over-current protection [ 10.017839] hub 3-0:1.0: power on to power good time: 2ms [ 10.018198] hub 3-0:1.0: local power source is good [ 10.018530] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 10.018962] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.019409] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 10.019847] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0) [ 10.020423] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 10.020845] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 10.021218] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 10.021571] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004' [ 10.021973] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 10.022523] uhci_hcd 0000:00:1a.1: detected 2 ports [ 10.022857] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 10.023280] uhci_hcd 0000:00:1a.1: Performing full reset [ 10.023639] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 10.024027] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 10.024434] usb usb4: default language 0x0409 [ 10.024756] usb usb4: udev 1, busnum 4, minor = 384 [ 10.025093] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.025495] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.026032] usb usb4: Product: UHCI Host Controller [ 10.026363] usb usb4: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd [ 10.026765] usb usb4: SerialNumber: 0000:00:1a.1 [ 10.027205] usb usb4: usb_probe_device [ 10.027497] usb usb4: configuration #1 chosen from 1 choice [ 10.027861] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 10.028294] hub 4-0:1.0: usb_probe_interface [ 10.028604] hub 4-0:1.0: usb_probe_interface - got id [ 10.028946] hub 4-0:1.0: USB hub found [ 10.029242] hub 4-0:1.0: 2 ports detected [ 10.029541] hub 4-0:1.0: standalone hub [ 10.029834] hub 4-0:1.0: no power switching (usb 1.0) [ 10.030176] hub 4-0:1.0: individual port over-current protection [ 10.030550] hub 4-0:1.0: power on to power good time: 2ms [ 10.030906] hub 4-0:1.0: local power source is good [ 10.031242] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 10.031671] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.032121] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 10.032551] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 10.032975] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 10.033343] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 10.033697] /c/wfg/linux/drivers/usb/core/inode.c: creating file '005' [ 10.034102] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 10.034653] uhci_hcd 0000:00:1a.2: detected 2 ports [ 10.034992] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 10.035392] uhci_hcd 0000:00:1a.2: Performing full reset [ 10.035752] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 10.036140] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 10.036546] usb usb5: default language 0x0409 [ 10.036868] usb usb5: udev 1, busnum 5, minor = 512 [ 10.037206] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.037611] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.038150] usb usb5: Product: UHCI Host Controller [ 10.038482] usb usb5: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd [ 10.038885] usb usb5: SerialNumber: 0000:00:1a.2 [ 10.039325] usb usb5: usb_probe_device [ 10.039616] usb usb5: configuration #1 chosen from 1 choice [ 10.039986] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 10.040416] hub 5-0:1.0: usb_probe_interface [ 10.040727] hub 5-0:1.0: usb_probe_interface - got id [ 10.041069] hub 5-0:1.0: USB hub found [ 10.041364] hub 5-0:1.0: 2 ports detected [ 10.041663] hub 5-0:1.0: standalone hub [ 10.041960] hub 5-0:1.0: no power switching (usb 1.0) [ 10.042297] hub 5-0:1.0: individual port over-current protection [ 10.042671] hub 5-0:1.0: power on to power good time: 2ms [ 10.043031] hub 5-0:1.0: local power source is good [ 10.043363] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 10.043795] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.044243] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 10.044676] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 10.045101] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 10.045469] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 10.045818] /c/wfg/linux/drivers/usb/core/inode.c: creating file '006' [ 10.046218] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 10.046768] uhci_hcd 0000:00:1d.0: detected 2 ports [ 10.047106] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 10.047505] uhci_hcd 0000:00:1d.0: Performing full reset [ 10.047867] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 10.048236] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 10.048641] usb usb6: default language 0x0409 [ 10.048967] usb usb6: udev 1, busnum 6, minor = 640 [ 10.049300] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.049702] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.050240] usb usb6: Product: UHCI Host Controller [ 10.050573] usb usb6: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd [ 10.050978] usb usb6: SerialNumber: 0000:00:1d.0 [ 10.051416] usb usb6: usb_probe_device [ 10.051708] usb usb6: configuration #1 chosen from 1 choice [ 10.052077] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 10.052510] hub 6-0:1.0: usb_probe_interface [ 10.052821] hub 6-0:1.0: usb_probe_interface - got id [ 10.053162] hub 6-0:1.0: USB hub found [ 10.053458] hub 6-0:1.0: 2 ports detected [ 10.053758] hub 6-0:1.0: standalone hub [ 10.054055] hub 6-0:1.0: no power switching (usb 1.0) [ 10.054394] hub 6-0:1.0: individual port over-current protection [ 10.054768] hub 6-0:1.0: power on to power good time: 2ms [ 10.055129] hub 6-0:1.0: local power source is good [ 10.055462] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 10.055895] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.056348] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 10.056770] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 10.057195] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 10.057564] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 10.057921] /c/wfg/linux/drivers/usb/core/inode.c: creating file '007' [ 10.058320] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 10.058874] uhci_hcd 0000:00:1d.1: detected 2 ports [ 10.062168] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 10.062566] uhci_hcd 0000:00:1d.1: Performing full reset [ 10.062929] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 10.063296] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 10.063698] usb usb7: default language 0x0409 [ 10.064024] usb usb7: udev 1, busnum 7, minor = 768 [ 10.064356] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.064757] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.065295] usb usb7: Product: UHCI Host Controller [ 10.065627] usb usb7: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd [ 10.066031] usb usb7: SerialNumber: 0000:00:1d.1 [ 10.066469] usb usb7: usb_probe_device [ 10.066760] usb usb7: configuration #1 chosen from 1 choice [ 10.067128] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 10.067558] hub 7-0:1.0: usb_probe_interface [ 10.067871] hub 7-0:1.0: usb_probe_interface - got id [ 10.068210] hub 7-0:1.0: USB hub found [ 10.068507] hub 7-0:1.0: 2 ports detected [ 10.068810] hub 7-0:1.0: standalone hub [ 10.069103] hub 7-0:1.0: no power switching (usb 1.0) [ 10.069441] hub 7-0:1.0: individual port over-current protection [ 10.069817] hub 7-0:1.0: power on to power good time: 2ms [ 10.070173] hub 7-0:1.0: local power source is good [ 10.070504] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 10.070935] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.071393] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 10.071819] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 10.072239] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 10.072607] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 10.072960] /c/wfg/linux/drivers/usb/core/inode.c: creating file '008' [ 10.073358] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 10.073931] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 10.074529] hub 1-0:1.0: port 1: status 0501 change 0001 [ 10.074893] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 10.074897] uhci_hcd 0000:00:1d.2: detected 2 ports [ 10.074903] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 10.074904] uhci_hcd 0000:00:1d.2: Performing full reset [ 10.074918] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 10.074926] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 10.074988] usb usb8: default language 0x0409 [ 10.075001] usb usb8: udev 1, busnum 8, minor = 896 [ 10.075003] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.075005] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.075007] usb usb8: Product: UHCI Host Controller [ 10.075009] usb usb8: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd [ 10.075010] usb usb8: SerialNumber: 0000:00:1d.2 [ 10.075168] usb usb8: usb_probe_device [ 10.075170] usb usb8: configuration #1 chosen from 1 choice [ 10.075181] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 10.075283] hub 8-0:1.0: usb_probe_interface [ 10.075285] hub 8-0:1.0: usb_probe_interface - got id [ 10.075287] hub 8-0:1.0: USB hub found [ 10.075295] hub 8-0:1.0: 2 ports detected [ 10.075296] hub 8-0:1.0: standalone hub [ 10.075298] hub 8-0:1.0: no power switching (usb 1.0) [ 10.075300] hub 8-0:1.0: individual port over-current protection [ 10.075301] hub 8-0:1.0: power on to power good time: 2ms [ 10.075314] hub 8-0:1.0: local power source is good [ 10.075316] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 10.075360] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 10.075497] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 10.075625] Initializing USB Mass Storage driver... [ 10.075730] usbcore: registered new interface driver usb-storage [ 10.075733] USB Mass Storage support registered. [ 10.075881] usbcore: registered new interface driver libusual [ 10.075947] usbcore: registered new interface driver ums-alauda [ 10.076016] usbcore: registered new interface driver ums-cypress [ 10.076091] usbcore: registered new interface driver ums-datafab [ 10.076163] usbcore: registered new interface driver ums-freecom [ 10.076239] usbcore: registered new interface driver ums-isd200 [ 10.076309] usbcore: registered new interface driver ums-jumpshot [ 10.076371] usbcore: registered new interface driver ums-karma [ 10.076437] usbcore: registered new interface driver ums-onetouch [ 10.076518] usbcore: registered new interface driver ums-sddr09 [ 10.076593] usbcore: registered new interface driver ums-sddr55 [ 10.076662] usbcore: registered new interface driver ums-usbat [ 10.076818] usbcore: registered new interface driver usbserial [ 10.076904] USB Serial support registered for generic [ 10.076991] usbcore: registered new interface driver usbserial_generic [ 10.076994] usbserial: USB Serial Driver core [ 10.077048] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 10.077119] usbcore: registered new interface driver belkin [ 10.077121] belkin_sa: v1.3:USB Belkin Serial converter driver [ 10.077180] USB Serial support registered for MCT U232 [ 10.077271] usbcore: registered new interface driver mct_u232 [ 10.077273] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver [ 10.077507] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 10.080800] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 10.080826] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 10.081109] mousedev: PS/2 mouse device common for all mice [ 10.081726] rtc_cmos 00:02: RTC can wake from S4 [ 10.081944] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 10.081984] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 10.082042] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 10.082225] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 10.082344] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 10.082348] iTCO_vendor_support: vendor-support=0 [ 10.082350] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 10.082359] md: linear personality registered for level -1 [ 10.082360] md: raid0 personality registered for level 0 [ 10.082362] md: raid1 personality registered for level 1 [ 10.082363] md: raid10 personality registered for level 10 [ 10.082364] md: raid6 personality registered for level 6 [ 10.082366] md: raid5 personality registered for level 5 [ 10.082367] md: raid4 personality registered for level 4 [ 10.082368] md: multipath personality registered for level -4 [ 10.082370] md: faulty personality registered for level -5 [ 10.102090] hub 1-0:1.0: port 2: status 0501 change 0001 [ 10.102456] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0 ACK POWER sig=j CSC CONNECT [ 10.103056] hub 1-0:1.0: port 4: status 0501 change 0001 [ 10.103405] device-mapper: uevent: version 1.0.3 [ 10.103857] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com [ 10.104588] device-mapper: multipath: version 1.3.0 loaded [ 10.104956] device-mapper: multipath round-robin: version 1.0.0 loaded [ 10.105350] device-mapper: multipath queue-length: version 0.1.0 loaded [ 10.105734] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 10.106106] device-mapper: multipath service-time: version 0.2.0 loaded [ 10.106598] device-mapper: dm-log-userspace: version 1.1.0 loaded [ 10.108281] cpuidle: using governor ladder [ 10.111238] cpuidle: using governor menu [ 10.111749] usbcore: registered new interface driver usbhid [ 10.112108] usbhid: USB HID core driver [ 10.112828] dell_wmi: No known WMI GUID found [ 10.113142] acer_wmi: Acer Laptop ACPI-WMI Extras [ 10.113469] acer_wmi: No or unsupported WMI interface, unable to load [ 10.114211] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0) [ 10.114794] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 10.115395] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 10.115798] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 10.116184] ALSA hda_intel.c:2598 chipset global capabilities = 0x4401 [ 10.116587] ALSA hda_intel.c:1091 Clearing TCSEL [ 10.117689] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 10.118054] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 10.124704] ALSA hda_intel.c:945 codec_mask = 0x4 [ 10.125248] ALSA hda_intel.c:1392 codec #2 probed OK [ 10.130661] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00 [ 10.130751] ALSA hda_codec.c:3955 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 10.130753] hda_codec: ALC889: SKU not ready 0x411111f0 [ 10.130973] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 10.133799] ALSA hda_codec.c:2339 Cannot find slave Side Playback Volume, skipped [ 10.134345] ALSA hda_codec.c:2339 Cannot find slave Headphone Playback Volume, skipped [ 10.134912] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Volume, skipped [ 10.135457] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Volume, skipped [ 10.136023] ALSA hda_codec.c:2339 Cannot find slave Side Playback Switch, skipped [ 10.136570] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Switch, skipped [ 10.137120] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Switch, skipped [ 10.138298] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 10.139263] ALSA device list: [ 10.139526] #0: HDA Intel at 0xf7f00000 irq 45 [ 10.139854] oprofile: using NMI interrupt. [ 10.140222] netem: version 1.3 [ 10.140488] Netfilter messages via NETLINK v0.30. [ 10.140899] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 10.141989] ctnetlink v0.93: registering with nfnetlink. [ 10.142374] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 10.142650] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 10.143197] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 10.144044] xt_time: kernel timezone is -0000 [ 10.145732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.149171] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 10.149584] arp_tables: (C) 2002 David S. Miller [ 10.149944] TCP bic registered [ 10.150209] TCP cubic registered [ 10.150478] TCP westwood registered [ 10.150807] TCP highspeed registered [ 10.151090] TCP hybla registered [ 10.151362] TCP htcp registered [ 10.151663] TCP vegas registered [ 10.151932] TCP veno registered [ 10.152199] TCP scalable registered [ 10.152478] TCP lp registered [ 10.152791] TCP yeah registered [ 10.153057] TCP illinois registered [ 10.153336] Initializing XFRM netlink socket [ 10.153666] NET: Registered protocol family 17 [ 10.153990] NET: Registered protocol family 15 [ 10.154623] Bridge firewalling registered [ 10.154933] Ebtables v2.0 registered [ 10.155304] [ 10.155304] printing PIC contents [ 10.155618] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 10.156143] ... PIC IMR: ffff [ 10.156408] ... PIC IRR: 0c21 [ 10.156734] ... PIC ISR: 0000 [ 10.157000] ... PIC ELCR: 0c20 [ 10.157266] printing local APIC contents on CPU#0/0: [ 10.157600] ... APIC ID: 00000000 (0) [ 10.157901] ... APIC VERSION: 00060015 [ 10.158189] ... APIC TASKPRI: 00000000 (00) [ 10.158493] ... APIC PROCPRI: 00000000 [ 10.158781] ... APIC LDR: 01000000 [ 10.159056] ... APIC DFR: ffffffff [ 10.159331] ... APIC SPIV: 000001ff [ 10.159609] ... APIC ISR field: [ 10.159875] 0000000000000000000000000000000000000000000000000000000000000000 [ 10.160555] ... APIC TMR field: [ 10.160820] 0000000000000000000000000000000000020000000000000000000000000000 [ 10.161501] ... APIC IRR field: [ 10.161767] 0000000000010000000000000000000000000200000000000000000000000000 [ 10.162449] ... APIC ESR: 00000000 [ 10.162724] ... APIC ICR: 000000ef [ 10.163000] ... APIC ICR2: 05000000 [ 10.163278] ... APIC LVTT: 000000ef [ 10.163559] ... APIC LVTPC: 00000400 [ 10.163840] ... APIC LVT0: 00010700 [ 10.164119] ... APIC LVT1: 00000400 [ 10.164398] ... APIC LVTERR: 000000fe [ 10.164683] ... APIC TMICT: 00063883 [ 10.164964] ... APIC TMCCT: 000136ab [ 10.165246] ... APIC TDCR: 00000003 [ 10.165524] [ 10.165730] number of MP IRQ sources: 15. [ 10.166048] number of IO-APIC #8 registers: 24. [ 10.166378] testing the IO APIC....................... [ 10.166779] [ 10.167001] IO APIC #8...... [ 10.167272] .... register #00: 08000000 [ 10.167593] ....... : physical APIC id: 08 [ 10.167916] ....... : Delivery Type: 0 [ 10.168229] ....... : LTS : 0 [ 10.168624] .... register #01: 00170020 [ 10.168931] ....... : max redirection entries: 17 [ 10.169269] ....... : PRQ implemented: 0 [ 10.169637] ....... : IO APIC version: 20 [ 10.169950] .... IRQ redirection table: [ 10.170242] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 10.170585] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 10.171012] 00 00 1 0 0 0 0 0 0 00 [ 10.171396] 01 00 0 0 0 0 0 0 0 31 [ 10.171862] 02 00 0 0 0 0 0 0 0 30 [ 10.172245] 03 00 0 0 0 0 0 0 0 33 [ 10.172677] 04 00 0 0 0 0 0 0 0 34 [ 10.173061] 05 00 0 0 0 0 0 0 0 35 [ 10.173442] 06 00 1 0 0 0 0 0 0 36 [ 10.173879] 07 00 0 0 0 0 0 0 0 37 [ 10.174258] 08 00 0 0 0 0 0 0 0 38 [ 10.174567] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 10.175051] 09 00 0 1 0 0 0 0 0 39 [ 10.175445] 0a 00 0 0 0 0 0 0 0 3A [ 10.175891] 0b 00 0 0 0 0 0 0 0 3B [ 10.176297] 0c 00 0 0 0 0 0 0 0 3C [ 10.176760] 0d 00 0 0 0 0 0 0 0 3D [ 10.177166] 0e 00 0 0 0 0 0 0 0 3E [ 10.177623] 0f 00 0 0 0 0 0 0 0 3F [ 10.178004] 10 00 0 1 0 1 0 0 0 29 [ 10.178384] 11 00 1 1 0 1 0 0 0 41 [ 10.178841] 12 00 0 1 0 1 0 0 0 91 [ 10.179221] 13 00 0 1 0 1 0 0 0 61 [ 10.179657] 14 00 1 1 0 1 0 0 0 71 [ 10.180039] 15 00 0 1 0 1 0 0 0 A1 [ 10.180419] 16 00 1 1 0 1 0 0 0 A9 [ 10.180879] 17 00 0 1 0 1 0 0 0 99 [ 10.181257] IRQ to pin mappings: [ 10.181581] IRQ0 -> 0:2 [ 10.181892] IRQ1 -> 0:1 [ 10.182201] IRQ3 -> 0:3 [ 10.182556] IRQ4 -> 0:4 [ 10.182865] IRQ5 -> 0:5 [ 10.183174] IRQ6 -> 0:6 [ 10.183552] IRQ7 -> 0:7 [ 10.183861] IRQ8 -> 0:8 [ 10.184170] IRQ9 -> 0:9 [ 10.184482] IRQ10 -> 0:10 [ 10.184828] IRQ11 -> 0:11 [ 10.185143] IRQ12 -> 0:12 [ 10.185548] IRQ13 -> 0:13 [ 10.185864] IRQ14 -> 0:14 [ 10.186181] IRQ15 -> 0:15 [ 10.186552] IRQ16 -> 0:16 [ 10.186869] IRQ17 -> 0:17 [ 10.187186] IRQ18 -> 0:18 [ 10.187551] IRQ19 -> 0:19 [ 10.187867] IRQ20 -> 0:20 [ 10.188181] IRQ21 -> 0:21 [ 10.188542] IRQ22 -> 0:22 [ 10.188856] IRQ23 -> 0:23 [ 10.189172] .................................... done. [ 10.190029] PM: Hibernation image not present or could not be loaded. [ 10.190450] registered taskstats version 1 [ 10.191508] Magic number: 7:585:47 [ 10.192103] rtc_cmos 00:02: setting system clock to 2011-08-17 22:02:24 UTC (1313618544) [ 10.202480] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000 [ 10.202871] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 10.206489] IP-Config: Complete: [ 10.206775] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 10.207361] host=fat, domain=, nis-domain=(none), [ 10.207800] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 10.253634] ehci_hcd 0000:00:1a.7: port 1 high speed [ 10.253971] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 10.305206] usb 1-1: new high speed USB device number 2 using ehci_hcd [ 10.358311] ehci_hcd 0000:00:1a.7: port 1 high speed [ 10.358668] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 10.428879] usb 1-1: default language 0x0409 [ 10.436027] usb 1-1: udev 2, busnum 1, minor = 1 [ 10.436375] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 10.436820] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.437304] usb 1-1: Product: AX88178 [ 10.437615] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 10.437986] usb 1-1: SerialNumber: 000013 [ 10.438561] usb 1-1: usb_probe_device [ 10.438921] usb 1-1: configuration #1 chosen from 1 choice [ 10.440013] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 10.441223] asix 1-1:1.0: usb_probe_interface [ 10.441559] asix 1-1:1.0: usb_probe_interface - got id [ 11.151725] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 11.152474] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002' [ 11.152944] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 11.152992] md: Waiting for all devices to be available before autodetect [ 11.152995] md: If you don't use raid, use raid=noautodetect [ 11.153765] md: Autodetecting RAID arrays. [ 11.153769] md: Scanned 0 and added 0 devices. [ 11.153770] md: autorun ... [ 11.153772] md: ... autorun DONE. [ 11.155426] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 11.162260] VFS: Mounted root (nfs filesystem) on device 0:15. [ 11.162746] debug: unmapping init memory ffffffff81ebe000..ffffffff82172000 [ 11.206326] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 11.206998] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s [ 11.255673] stty used greatest stack depth: 4544 bytes left [ 11.259393] ehci_hcd 0000:00:1a.7: port 4 high speed [ 11.259767] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 11.270142] usb usb5: suspend_rh (auto-stop) [ 11.270147] usb usb8: suspend_rh (auto-stop) [ 11.270838] usb usb6: suspend_rh (auto-stop) [ 11.271243] usb usb7: suspend_rh (auto-stop) [ 11.271633] usb usb4: suspend_rh (auto-stop) [ 11.284532] uname used greatest stack depth: 3872 bytes left [ 11.292916] sed used greatest stack depth: 3728 bytes left [ 11.312030] usb 1-4: new high speed USB device number 4 using ehci_hcd [ 11.325559] sh used greatest stack depth: 3696 bytes left [ 11.345983] mountpoint used greatest stack depth: 3600 bytes left [ 11.363073] ehci_hcd 0000:00:1a.7: port 4 high speed [ 11.363430] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 12.361867] usb 1-4: default language 0x0409 [ 12.363763] usb 1-4: udev 4, busnum 1, minor = 3 [ 12.364095] usb 1-4: New USB device found, idVendor=1307, idProduct=0165 [ 12.364498] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.364973] usb 1-4: Product: USB Mass Storage Device [ 12.365315] usb 1-4: Manufacturer: Teclast Technology [ 12.365655] usb 1-4: SerialNumber: 0000000000020D [ 12.366207] usb 1-4: usb_probe_device [ 12.366509] usb 1-4: configuration #1 chosen from 1 choice [ 12.367112] usb 1-4: adding 1-4:1.0 (config #1, interface 0) [ 12.367538] usb-storage 1-4:1.0: usb_probe_interface [ 12.367954] usb-storage 1-4:1.0: usb_probe_interface - got id [ 12.368508] scsi9 : usb-storage 1-4:1.0 [ 12.369160] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004' [ 12.369584] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 12.370047] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 12.370403] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 12.475412] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 12.577113] usb 3-2: new low speed USB device number 2 using uhci_hcd [ 12.580762] usb 3-2: uhci_result_common: failed with status 440000 [ 12.584754] usb 3-2: uhci_result_common: failed with status 440000 [ 12.586212] S04ssh used greatest stack depth: 3552 bytes left [ 12.588691] usb 3-2: uhci_result_common: failed with status 440000 [ 12.690728] usb 3-2: device descriptor read/64, error -71 [ 12.795052] usb 3-2: uhci_result_common: failed with status 440000 [ 12.799044] usb 3-2: uhci_result_common: failed with status 440000 [ 12.803030] usb 3-2: uhci_result_common: failed with status 440000 [ 12.905050] usb 3-2: device descriptor read/64, error -71 [ 13.056787] EXT4-fs (sda5): recovery complete [ 13.057203] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 13.107516] usb 3-2: new low speed USB device number 3 using uhci_hcd [ 13.112069] usb 3-2: uhci_result_common: failed with status 440000 [ 13.116056] usb 3-2: uhci_result_common: failed with status 440000 [ 13.120044] usb 3-2: uhci_result_common: failed with status 440000 [ 13.222155] usb 3-2: device descriptor read/64, error -71 [ 13.326406] usb 3-2: uhci_result_common: failed with status 440000 [ 13.330392] usb 3-2: uhci_result_common: failed with status 440000 [ 13.334429] usb 3-2: uhci_result_common: failed with status 440000 [ 13.367853] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 13.436506] usb 3-2: device descriptor read/64, error -71 [ 13.483067] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 13.484438] sd 9:0:0:0: [sdb] Write Protect is off [ 13.484798] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 13.485802] sd 9:0:0:0: [sdb] Asking for cache data failed [ 13.486197] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 13.491028] sd 9:0:0:0: [sdb] Asking for cache data failed [ 13.491432] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 13.625343] sdb: sdb1 sdb2 sdb3 [ 13.628830] sd 9:0:0:0: [sdb] Asking for cache data failed [ 13.629186] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 13.629559] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 13.638867] usb 3-2: new low speed USB device number 4 using uhci_hcd [ 13.642426] usb 3-2: uhci_result_common: failed with status 440000 [ 13.770856] mount.nfs used greatest stack depth: 3152 bytes left [ 13.846792] usb 3-2: uhci_result_common: failed with status 440000 [ 14.048507] usb 3-2: device not accepting address 4, error -71 [ 14.150206] usb 3-2: new low speed USB device number 5 using uhci_hcd [ 14.153841] usb 3-2: uhci_result_common: failed with status 440000 [ 14.358251] usb 3-2: uhci_result_common: failed with status 440000 [ 14.558954] usb 3-2: device not accepting address 5, error -71 [ 14.559376] hub 3-0:1.0: unable to enumerate USB device on port 2 [ 14.559784] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 14.560175] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 46.726732] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)