[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.1.0-rc1-no-maxpause+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #198 SMP Tue Aug 16 08:31:11 CST 2011
[    0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1-no-maxpause+ 
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   Centaur CentaurHauls
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009cc00 (usable)
[    0.000000]  BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bcda4000 (usable)
[    0.000000]  BIOS-e820: 00000000bcda4000 - 00000000bcfdd000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bcfdd000 - 00000000bf6bd000 (usable)
[    0.000000]  BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved)
[    0.000000]  BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable)
[    0.000000]  BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable)
[    0.000000]  BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable)
[    0.000000]  BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.5 present.
[    0.000000] DMI:                  /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Scan SMP from ffff880000000000 for 1024 bytes.
[    0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes.
[    0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes.
[    0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0
[    0.000000]   mpc: ff4d0-ff6a8
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000bf800000
[    0.000000]  0000000000 - 00bf800000 page 4k
[    0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000
[    0.000000] log_buf_len: 8388608
[    0.000000] early log buf free: 258293(98%)
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
[    0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL  DX58SO   0000084F      01000013)
[    0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560)
[    0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610)
[    0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: FACS 00000000bf726000 00040
[    0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL  SSDT  PM 0000084F MSFT 0100000D)
[    0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL  PerfTune 0000084F MSFT 0100000D)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] mapped APIC to ffffffffff5fb000 (        fee00000)
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-00000000bf800000
[    0.000000] Initmem setup node 0 0000000000000000-00000000bf800000
[    0.000000]   NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff]
[    0.000000]  [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800b9c00000-ffff8800bc5fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[6] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009c
[    0.000000]     0: 0x00000100 -> 0x000bcda4
[    0.000000]     0: 0x000bcfdd -> 0x000bf6bd
[    0.000000]     0: 0x000bf6bf -> 0x000bf714
[    0.000000]     0: 0x000bf7bf -> 0x000bf7e7
[    0.000000]     0: 0x000bf7ff -> 0x000bf800
[    0.000000] On node 0 totalpages: 783502
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3919 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10668 pages used for memmap
[    0.000000]   DMA32 zone: 768854 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] mapped APIC to ffffffffff5fb000 (        fee00000)
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs
[    0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000)
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bcda4000 - 00000000bcfdd000
[    0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000
[    0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000
[    0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1
[    0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915008 r8192 d22400 u2097152
[    0.000000] pcpu-alloc: s1915008 r8192 d22400 u2097152 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 
[    0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 772773
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1-no-maxpause+ 
[    0.000000] sysrq: sysrq always enabled.
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 3019044k/3137536k available (9445k kernel code, 3528k absent, 114964k reserved, 5641k data, 2768k init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU debugfs-based tracing is enabled.
[    0.000000] NR_IRQS:4352 nr_irqs:808 16
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] console [ttyS0] enabled
[    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.000000] ... MAX_LOCK_DEPTH:          48
[    0.000000] ... MAX_LOCKDEP_KEYS:        8191
[    0.000000] ... CLASSHASH_SIZE:          4096
[    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
[    0.000000] ... CHAINHASH_SIZE:          16384
[    0.000000]  memory used by lock dependency info: 6335 kB
[    0.000000]  per task-struct memory footprint: 2688 bytes
[    0.000000] allocated 25165824 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.001000] Fast TSC calibration using PIT
[    0.002000] Detected 3199.660 MHz processor.
[    0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.32 BogoMIPS (lpj=3199660)
[    0.000710] pid_max: default: 32768 minimum: 301
[    0.001933] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.004005] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.005019] Mount-cache hash table entries: 256
[    0.005741] Initializing cgroup subsys debug
[    0.006052] Initializing cgroup subsys cpuacct
[    0.006384] Initializing cgroup subsys memory
[    0.006724] Initializing cgroup subsys devices
[    0.007040] Initializing cgroup subsys freezer
[    0.007366] Initializing cgroup subsys blkio
[    0.007732] CPU: Physical Processor ID: 0
[    0.008032] CPU: Processor Core ID: 0
[    0.008330] mce: CPU supports 9 MCE banks
[    0.008636] CPU0: Thermal monitoring enabled (TM1)
[    0.008974] using mwait in idle threads.
[    0.010124] ACPI: Core revision 20110623
[    0.022149] ftrace: allocating 36036 entries in 142 pages
[    0.030662] Getting VERSION: 60015
[    0.030939] Getting VERSION: 60015
[    0.031225] Getting ID: 0
[    0.031470] Getting ID: 0
[    0.031717] Switched APIC routing to physical flat.
[    0.032046] enabled ExtINT on CPU#0
[    0.032490] ENABLING IO-APIC IRQs
[    0.032762] init IO_APIC IRQs
[    0.033020]  apic 8 pin 0 not connected
[    0.033326] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
[    0.033892] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
[    0.034466] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0)
[    0.035031] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0)
[    0.035598] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0)
[    0.036162] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0)
[    0.036729] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0)
[    0.037296] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0)
[    0.037861] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0)
[    0.038429] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0)
[    0.039000] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0)
[    0.039573] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0)
[    0.040143] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0)
[    0.040716] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0)
[    0.041288] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0)
[    0.041856]  apic 8 pin 16 not connected
[    0.042150]  apic 8 pin 17 not connected
[    0.042446]  apic 8 pin 18 not connected
[    0.042741]  apic 8 pin 19 not connected
[    0.043035]  apic 8 pin 20 not connected
[    0.043332]  apic 8 pin 21 not connected
[    0.043626]  apic 8 pin 22 not connected
[    0.043920]  apic 8 pin 23 not connected
[    0.044351] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.054722] CPU0: Genuine Intel(R) CPU             000  @ 3.20GHz stepping 04
[    0.055206] Using local APIC timer interrupts.
[    0.055207] calibrating APIC timer ...
[    0.157160] ... lapic delta = 833239
[    0.157442] ... PM-Timer delta = 357901
[    0.157733] ... PM-Timer result ok
[    0.158008] ..... delta 833239
[    0.158270] ..... mult: 35792783
[    0.158538] ..... calibration result: 133318
[    0.158846] ..... CPU clock speed is 3199.0635 MHz.
[    0.159175] ..... host bus clock speed is 133.0318 MHz.
[    0.159529] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver.
[    0.160291] ... version:                3
[    0.160590] ... bit width:              48
[    0.160890] ... generic registers:      4
[    0.161187] ... value mask:             0000ffffffffffff
[    0.161535] ... max period:             000000007fffffff
[    0.161880] ... fixed-purpose events:   3
[    0.162178] ... event mask:             000000070000000f
[    0.162918] lockdep: fixing up alternatives.
[    0.163290] Booting Node   0, Processors  #1
[    0.163509] smpboot cpu 1: start_ip = 97000
[    0.175081] masked ExtINT on CPU#1
[    0.254820] lockdep: fixing up alternatives.
[    0.255154]  #2
[    0.255246] smpboot cpu 2: start_ip = 97000
[    0.266819] masked ExtINT on CPU#2
[    0.346746] lockdep: fixing up alternatives.
[    0.347080]  #3
[    0.347172] smpboot cpu 3: start_ip = 97000
[    0.358744] masked ExtINT on CPU#3
[    0.438770] lockdep: fixing up alternatives.
[    0.439107]  #4
[    0.439199] smpboot cpu 4: start_ip = 97000
[    0.450772] masked ExtINT on CPU#4
[    0.530748] lockdep: fixing up alternatives.
[    0.531086]  #5
[    0.531178] smpboot cpu 5: start_ip = 97000
[    0.542748] masked ExtINT on CPU#5
[    0.622686] lockdep: fixing up alternatives.
[    0.623025]  #6
[    0.623117] smpboot cpu 6: start_ip = 97000
[    0.637655] masked ExtINT on CPU#6
[    0.717690] lockdep: fixing up alternatives.
[    0.718027]  #7
[    0.718119] smpboot cpu 7: start_ip = 97000
[    0.729688] masked ExtINT on CPU#7
[    0.809418] Brought up 8 CPUs
[    0.809681] Total of 8 processors activated (51187.01 BogoMIPS).
[    0.813426] CPU0 attaching sched-domain:
[    0.813725]  domain 0: span 0,4 level SIBLING
[    0.814070]   groups: 0 (cpu_power = 589) 4 (cpu_power = 589)
[    0.814603]   domain 1: span 0-7 level MC
[    0.814934]    groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
[    0.815889] CPU1 attaching sched-domain:
[    0.816184]  domain 0: span 1,5 level SIBLING
[    0.816530]   groups: 1 (cpu_power = 589) 5 (cpu_power = 589)
[    0.817060]   domain 1: span 0-7 level MC
[    0.817392]    groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
[    0.818343] CPU2 attaching sched-domain:
[    0.818641]  domain 0: span 2,6 level SIBLING
[    0.818985]   groups: 2 (cpu_power = 589) 6 (cpu_power = 589)
[    0.819518]   domain 1: span 0-7 level MC
[    0.819848]    groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
[    0.820801] CPU3 attaching sched-domain:
[    0.821095]  domain 0: span 3,7 level SIBLING
[    0.821441]   groups: 3 (cpu_power = 589) 7 (cpu_power = 589)
[    0.821971]   domain 1: span 0-7 level MC
[    0.822302]    groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
[    0.823255] CPU4 attaching sched-domain:
[    0.823552]  domain 0: span 0,4 level SIBLING
[    0.823896]   groups: 4 (cpu_power = 589) 0 (cpu_power = 589)
[    0.824427]   domain 1: span 0-7 level MC
[    0.824759]    groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
[    0.825714] CPU5 attaching sched-domain:
[    0.826008]  domain 0: span 1,5 level SIBLING
[    0.826355]   groups: 5 (cpu_power = 589) 1 (cpu_power = 589)
[    0.826884]   domain 1: span 0-7 level MC
[    0.827215]    groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
[    0.828171] CPU6 attaching sched-domain:
[    0.828468]  domain 0: span 2,6 level SIBLING
[    0.828812]   groups: 6 (cpu_power = 589) 2 (cpu_power = 589)
[    0.829344]   domain 1: span 0-7 level MC
[    0.829676]    groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
[    0.830632] CPU7 attaching sched-domain:
[    0.830926]  domain 0: span 3,7 level SIBLING
[    0.831269]   groups: 7 (cpu_power = 589) 3 (cpu_power = 589)
[    0.831801]   domain 1: span 0-7 level MC
[    0.832132]    groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
[    0.833589] kworker/u:0 used greatest stack depth: 5288 bytes left
[    0.835866] PM: Registering ACPI NVS region at bcda4000 (2330624 bytes)
[    0.836363] PM: Registering ACPI NVS region at bf714000 (700416 bytes)
[    0.837480] xor: automatically using best checksumming function: generic_sse
[    0.842340]    generic_sse: 11928.000 MB/sec
[    0.842649] xor: using function: generic_sse (11928.000 MB/sec)
[    0.843098] RTC time: 21:27:46, date: 08/17/11
[    0.843534] NET: Registered protocol family 16
[    0.844618] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.845171] ACPI: bus type pci registered
[    0.845666] dca service started, version 1.12.1
[    0.846060] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.846675] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.860744] PCI: Using configuration type 1 for base access
[    0.883079] bio: create slab <bio-0> at 0
[    0.900330] raid6: int64x1   3171 MB/s
[    0.917320] raid6: int64x2   3402 MB/s
[    0.934317] raid6: int64x4   2738 MB/s
[    0.951334] raid6: int64x8   2085 MB/s
[    0.968307] raid6: sse2x1    7945 MB/s
[    0.985301] raid6: sse2x2    9289 MB/s
[    1.002299] raid6: sse2x4   10558 MB/s
[    1.002587] raid6: using algorithm sse2x4 (10558 MB/s)
[    1.003011] ACPI: Added _OSI(Module Device)
[    1.003325] ACPI: Added _OSI(Processor Device)
[    1.003640] ACPI: Added _OSI(3.0 _SCP Extensions)
[    1.003964] ACPI: Added _OSI(Processor Aggregator Device)
[    1.008277] ACPI: EC: Look up EC in DSDT
[    1.030503] ACPI: Interpreter enabled
[    1.030790] ACPI: (supports S0 S1 S3 S4 S5)
[    1.031302] ACPI: Using IOAPIC for interrupt routing
[    1.044195] ACPI: No dock devices found.
[    1.044498] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    1.045732] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d])
[    1.047413] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    1.047808] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    1.048202] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    1.048742] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff]
[    1.049278] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff]
[    1.049820] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff]
[    1.050382] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600
[    1.050821] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604
[    1.051245] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    1.051628] pci 0000:00:01.0: PME# disabled
[    1.051960] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604
[    1.052389] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[    1.052767] pci 0000:00:03.0: PME# disabled
[    1.053098] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604
[    1.053527] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    1.053904] pci 0000:00:07.0: PME# disabled
[    1.054238] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800
[    1.054686] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800
[    1.055134] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800
[    1.055581] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800
[    1.056025] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800
[    1.056473] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800
[    1.056922] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200
[    1.057314] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff]
[    1.057700] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff]
[    1.058084] pci 0000:00:19.0: reg 18: [io  0x2100-0x211f]
[    1.058496] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    1.058874] pci 0000:00:19.0: PME# disabled
[    1.059197] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03
[    1.059621] pci 0000:00:1a.0: reg 20: [io  0x20e0-0x20ff]
[    1.060025] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03
[    1.060450] pci 0000:00:1a.1: reg 20: [io  0x20c0-0x20df]
[    1.060853] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03
[    1.061274] pci 0000:00:1a.2: reg 20: [io  0x20a0-0x20bf]
[    1.061696] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03
[    1.062086] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff]
[    1.062550] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    1.062927] pci 0000:00:1a.7: PME# disabled
[    1.063255] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403
[    1.063643] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit]
[    1.064106] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    1.064487] pci 0000:00:1b.0: PME# disabled
[    1.064815] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604
[    1.065253] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.065636] pci 0000:00:1c.0: PME# disabled
[    1.065963] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604
[    1.066405] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    1.066781] pci 0000:00:1c.1: PME# disabled
[    1.067114] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604
[    1.067554] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    1.067932] pci 0000:00:1c.4: PME# disabled
[    1.068263] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03
[    1.068687] pci 0000:00:1d.0: reg 20: [io  0x2080-0x209f]
[    1.069093] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03
[    1.069517] pci 0000:00:1d.1: reg 20: [io  0x2060-0x207f]
[    1.069921] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03
[    1.070344] pci 0000:00:1d.2: reg 20: [io  0x2040-0x205f]
[    1.070759] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03
[    1.071148] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff]
[    1.071610] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    1.071989] pci 0000:00:1d.7: PME# disabled
[    1.072316] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[    1.072759] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601
[    1.073227] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    1.073613] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
[    1.074160] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
[    1.074754] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106
[    1.075142] pci 0000:00:1f.2: reg 10: [io  0x2128-0x212f]
[    1.075504] pci 0000:00:1f.2: reg 14: [io  0x2134-0x2137]
[    1.075862] pci 0000:00:1f.2: reg 18: [io  0x2120-0x2127]
[    1.076219] pci 0000:00:1f.2: reg 1c: [io  0x2130-0x2133]
[    1.076581] pci 0000:00:1f.2: reg 20: [io  0x2020-0x203f]
[    1.076939] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff]
[    1.077356] pci 0000:00:1f.2: PME# supported from D3hot
[    1.077704] pci 0000:00:1f.2: PME# disabled
[    1.078028] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05
[    1.078418] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit]
[    1.078839] pci 0000:00:1f.3: reg 20: [io  0x2000-0x201f]
[    1.079264] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    1.079672] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300
[    1.080052] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff]
[    1.080438] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref]
[    1.080867] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
[    1.081283] pci 0000:02:00.0: supports D1 D2
[    1.084589] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403
[    1.084968] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff]
[    1.085414] pci 0000:02:00.1: supports D1 D2
[    1.085738] pci 0000:00:03.0: PCI bridge to [bus 02-02]
[    1.086085] pci 0000:00:03.0:   bridge window [mem 0xe0200000-0xe02fffff]
[    1.086492] pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.087090] pci 0000:00:07.0: PCI bridge to [bus 03-03]
[    1.087494] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
[    1.087895] pci 0000:00:1c.1: PCI bridge to [bus 05-05]
[    1.088323] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101
[    1.088712] pci 0000:06:00.0: reg 10: [io  0x1018-0x101f]
[    1.089075] pci 0000:06:00.0: reg 14: [io  0x1024-0x1027]
[    1.089443] pci 0000:06:00.0: reg 18: [io  0x1010-0x1017]
[    1.089806] pci 0000:06:00.0: reg 1c: [io  0x1020-0x1023]
[    1.090169] pci 0000:06:00.0: reg 20: [io  0x1000-0x100f]
[    1.090537] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff]
[    1.090975] pci 0000:06:00.0: supports D1
[    1.091274] pci 0000:06:00.0: PME# supported from D0 D1 D3hot
[    1.091641] pci 0000:06:00.0: PME# disabled
[    1.091965] pci 0000:00:1c.4: PCI bridge to [bus 06-06]
[    1.092313] pci 0000:00:1c.4:   bridge window [io  0x1000-0x1fff]
[    1.092691] pci 0000:00:1c.4:   bridge window [mem 0xe0100000-0xe01fffff]
[    1.093144] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00
[    1.093535] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff]
[    1.093920] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff]
[    1.094371] pci 0000:07:03.0: supports D1 D2
[    1.094680] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot
[    1.095062] pci 0000:07:03.0: PME# disabled
[    1.095425] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
[    1.095839] pci 0000:00:1e.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    1.096245] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    1.096807] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    1.097368] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    1.097952] pci 0000:00:1e.0:   bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode)
[    1.098538] pci 0000:00:1e.0:   bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode)
[    1.099123] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode)
[    1.099747] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    1.101105] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[    1.101746] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
[    1.102218] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
[    1.102695] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
[    1.103165] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[    1.103641] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[    1.104124] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[    1.104696]  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19)
[    1.129047] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    1.130134] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    1.131216] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    1.132307] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    1.133393] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    1.134474] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    1.135556] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    1.136643] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    1.137915] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[    1.138491] vgaarb: loaded
[    1.138741] vgaarb: bridge control possible 0000:02:00.0
[    1.139392] SCSI subsystem initialized
[    1.139847] libata version 3.00 loaded.
[    1.140407] usbcore: registered new interface driver usbfs
[    1.140817] usbcore: registered new interface driver hub
[    1.141234] usbcore: registered new device driver usb
[    1.142012] wmi: Mapper loaded
[    1.142343] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    1.142729] PCI: Using ACPI for IRQ routing
[    1.144618] PCI: Discovered peer bus 3f
[    1.144989] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600
[    1.145394] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600
[    1.145798] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600
[    1.146195] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600
[    1.146602] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600
[    1.146998] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600
[    1.147402] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600
[    1.147801] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600
[    1.148198] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600
[    1.148599] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600
[    1.148996] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600
[    1.149403] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600
[    1.149802] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600
[    1.150197] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600
[    1.150599] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600
[    1.150999] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600
[    1.151401] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600
[    1.151797] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600
[    1.152194] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600
[    1.153978] PCI: pci_cache_line_size set to 64 bytes
[    1.154560] reserve RAM buffer: 000000000009cc00 - 000000000009ffff 
[    1.154823] reserve RAM buffer: 00000000bcda4000 - 00000000bfffffff 
[    1.155242] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff 
[    1.155666] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff 
[    1.156084] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff 
[    1.156507] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff 
[    1.187930] pnp: PnP ACPI init
[    1.188373] ACPI: bus type pnp registered
[    1.189327] pnp 00:00: [bus 00-3d]
[    1.189606] pnp 00:00: [io  0x0cf8-0x0cff]
[    1.189910] pnp 00:00: [io  0x0000-0x0cf7 window]
[    1.190234] pnp 00:00: [io  0x0d00-0xffff window]
[    1.190569] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    1.190919] pnp 00:00: [mem 0x000c4000-0x000cbfff window]
[    1.191275] pnp 00:00: [mem 0xfed40000-0xfedfffff window]
[    1.191626] pnp 00:00: [mem 0xd0000000-0xf7ffffff window]
[    1.191976] pnp 00:00: [mem 0x00000000 window]
[    1.192432] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    1.193114] pnp 00:01: [io  0x0000-0x000f]
[    1.193420] pnp 00:01: [io  0x0081-0x0083]
[    1.193724] pnp 00:01: [io  0x0087]
[    1.194002] pnp 00:01: [io  0x0089-0x008b]
[    1.194307] pnp 00:01: [io  0x008f]
[    1.194586] pnp 00:01: [io  0x00c0-0x00df]
[    1.194889] pnp 00:01: [dma 4]
[    1.195249] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    1.195658] pnp 00:02: [io  0x0070-0x0071]
[    1.195959] pnp 00:02: [io  0x0074-0x0077]
[    1.196269] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0)
[    1.196833] pnp 00:02: [irq 8]
[    1.197190] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.197608] pnp 00:03: [io  0x00f0]
[    1.197889] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0)
[    1.198462] pnp 00:03: [irq 13]
[    1.198819] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    1.199230] pnp 00:04: [io  0x0061]
[    1.199610] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    1.200022] pnp 00:05: [io  0x0500-0x053f]
[    1.200328] pnp 00:05: [io  0x0400-0x047f]
[    1.200630] pnp 00:05: [io  0x0092]
[    1.200909] pnp 00:05: [io  0x0680-0x06ff]
[    1.201210] pnp 00:05: [io  0x0010-0x001f]
[    1.201514] pnp 00:05: [io  0x0072-0x0073]
[    1.201814] pnp 00:05: [io  0x0080]
[    1.202093] pnp 00:05: [io  0x0084-0x0086]
[    1.202398] pnp 00:05: [io  0x0088]
[    1.202677] pnp 00:05: [io  0x008c-0x008e]
[    1.202978] pnp 00:05: [io  0x0090-0x009f]
[    1.203467] system 00:05: [io  0x0500-0x053f] has been reserved
[    1.203837] system 00:05: [io  0x0400-0x047f] has been reserved
[    1.204207] system 00:05: [io  0x0680-0x06ff] has been reserved
[    1.204582] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.205064] pnp 00:06: [io  0x0060]
[    1.205352] pnp 00:06: [io  0x0064]
[    1.205798] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.206765] pnp 00:07: [mem 0xfec00000-0xfec000ff]
[    1.207201] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active)
[    1.207736] pnp: PnP ACPI: found 8 devices
[    1.208039] ACPI: ACPI bus type pnp unregistered
[    1.217975] Switching to clocksource acpi_pm
[    1.218475] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[    1.219090] PCI: max bus depth: 1 pci_try_num: 2
[    1.219295] Switched to NOHz mode on CPU #2
[    1.219300] Switched to NOHz mode on CPU #7
[    1.219313] Switched to NOHz mode on CPU #5
[    1.219328] Switched to NOHz mode on CPU #1
[    1.219344] Switched to NOHz mode on CPU #3
[    1.219350] Switched to NOHz mode on CPU #6
[    1.219363] Switched to NOHz mode on CPU #4
[    1.221587] Switched to NOHz mode on CPU #0
[    1.221953] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    1.222307] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref]
[    1.222848] pci 0000:00:03.0: PCI bridge to [bus 02-02]
[    1.223194] pci 0000:00:03.0:   bridge window [mem 0xe0200000-0xe02fffff]
[    1.226581] pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.227137] pci 0000:00:07.0: PCI bridge to [bus 03-03]
[    1.227488] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
[    1.227847] pci 0000:00:1c.1: PCI bridge to [bus 05-05]
[    1.228200] pci 0000:00:1c.4: PCI bridge to [bus 06-06]
[    1.228557] pci 0000:00:1c.4:   bridge window [io  0x1000-0x1fff]
[    1.228935] pci 0000:00:1c.4:   bridge window [mem 0xe0100000-0xe01fffff]
[    1.229343] pci 0000:00:1e.0: PCI bridge to [bus 07-07]
[    1.229703] pci 0000:00:1e.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    1.230124] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0)
[    1.230707] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.231108] pci 0000:00:01.0: setting latency timer to 64
[    1.231461] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.231866] pci 0000:00:03.0: setting latency timer to 64
[    1.232220] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.232633] pci 0000:00:07.0: setting latency timer to 64
[    1.232993] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0)
[    1.233573] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.233974] pci 0000:00:1c.0: setting latency timer to 64
[    1.234329] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    1.234743] pci 0000:00:1c.1: setting latency timer to 64
[    1.235098] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.235497] pci 0000:00:1c.4: setting latency timer to 64
[    1.235862] pci 0000:00:1e.0: setting latency timer to 64
[    1.236212] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    1.236581] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    1.236937] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    1.237318] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff]
[    1.237714] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff]
[    1.238095] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff]
[    1.238476] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff]
[    1.238863] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.239396] pci_bus 0000:06: resource 0 [io  0x1000-0x1fff]
[    1.239757] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff]
[    1.240138] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff]
[    1.240533] pci_bus 0000:07: resource 4 [io  0x0000-0x0cf7]
[    1.240889] pci_bus 0000:07: resource 5 [io  0x0d00-0xffff]
[    1.241245] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff]
[    1.241640] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff]
[    1.242022] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff]
[    1.242402] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff]
[    1.242789] pci_bus 0000:3f: resource 0 [io  0x0000-0xffff]
[    1.243144] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff]
[    1.243692] NET: Registered protocol family 2
[    1.244358] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    1.246917] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    1.250736] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes)
[    1.254131] TCP: Hash tables configured (established 524288 bind 65536)
[    1.254559] TCP reno registered
[    1.254896] UDP hash table entries: 2048 (order: 6, 393216 bytes)
[    1.255538] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes)
[    1.256333] NET: Registered protocol family 1
[    1.256927] RPC: Registered named UNIX socket transport module.
[    1.257298] RPC: Registered udp transport module.
[    1.257641] RPC: Registered tcp transport module.
[    1.257966] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.258397] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10
[    1.258795] pci 0000:00:1a.0: Performing full reset
[    1.259142] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010
[    1.259541] pci 0000:00:1a.1: Performing full reset
[    1.259887] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010
[    1.260277] pci 0000:00:1a.2: Performing full reset
[    1.260785] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
[    1.261176] pci 0000:00:1d.0: Performing full reset
[    1.261547] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
[    1.261939] pci 0000:00:1d.1: Performing full reset
[    1.262286] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
[    1.262688] pci 0000:00:1d.2: Performing full reset
[    1.263179] pci 0000:02:00.0: Boot video device
[    1.263566] PCI: CLS 64 bytes, default 64
[    1.267777] Machine check injector initialized
[    1.269646] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6
[    1.270018] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6
[    1.270391] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6
[    1.270762] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6
[    1.271133] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6
[    1.271508] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6
[    1.271878] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6
[    1.272248] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6
[    1.272702] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.273787] audit: initializing netlink socket (disabled)
[    1.274166] type=2000 audit(1313616466.025:1): initialized
[    1.304627] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.306590] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.307304] fuse init (API version 7.16)
[    1.307815] JFS: nTxBlock = 8192, nTxLock = 65536
[    1.311313] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    1.312683] NILFS version 2 loaded
[    1.313262] Btrfs loaded
[    1.313527] msgmni has been set to 5896
[    1.314676] async_tx: api initialized (async)
[    1.315085] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.315697] io scheduler noop registered
[    1.315994] io scheduler deadline registered
[    1.316355] io scheduler cfq registered (default)
[    1.317138] pcieport 0000:00:1c.0: setting latency timer to 64
[    1.317576] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    1.318052] pcieport 0000:00:1c.1: setting latency timer to 64
[    1.318467] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[    1.318952] pcieport 0000:00:1c.4: setting latency timer to 64
[    1.319367] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X
[    1.320093] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.320927] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0
[    1.321508] ACPI: Sleep Button [SLPB]
[    1.321944] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    1.322487] ACPI: Power Button [PWRF]
[    1.323503] ACPI: acpi_idle registered with cpuidle
[    1.324267] Monitor-Mwait will be used to enter C-1 state
[    1.324688] Monitor-Mwait will be used to enter C-3 state
[    1.332392] ioatdma: Intel(R) QuickData Technology Driver 4.00
[    1.376783] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.395618] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[    1.443821] Initializing Nozomi driver 2.1d
[    1.444634] Non-volatile memory driver v1.3
[    1.445377] Linux agpgart interface v0.103
[    1.445776] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[    1.446373] Hangcheck: Using getrawmonotonic().
[    1.446771] [drm] Initialized drm 1.1.0 20060810
[    1.447092] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module!
[    2.265617] Refined TSC clocksource calibration: 3200.113 MHz.
[    2.265987] Switching to clocksource tsc
[    4.463712] floppy0: no floppy controllers found
[    4.595577] brd: module loaded
[    4.597378] loop: module loaded
[    4.598133] Loading iSCSI transport class v2.0-870.
[    4.599058] Loading Adaptec I2O RAID: Version 2.4 Build 5go
[    4.599414] Detecting Adaptec I2O RAID controllers...
[    4.599939] Adaptec aacraid driver 1.1-7[28000]-ms
[    4.600828] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[    4.601449] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.03-k.
[    4.602195] iscsi: registered transport (qla4xxx)
[    4.602594] QLogic iSCSI HBA Driver
[    4.602955] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    4.603564] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    4.604055] megasas: 00.00.05.40-rc1 Tue. Jul. 26 17:00:00 PDT 2011
[    4.604519] mpt2sas version 09.100.00.00 loaded
[    4.605235] ahci 0000:00:1f.2: version 3.0
[    4.605567] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0)
[    4.606141] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    4.606593] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
[    4.607014] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[    4.607585] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems 
[    4.608153] ahci 0000:00:1f.2: setting latency timer to 64
[    4.618961] scsi0 : ahci
[    4.619427] scsi1 : ahci
[    4.619837] scsi2 : ahci
[    4.620234] scsi3 : ahci
[    4.620655] scsi4 : ahci
[    4.621054] scsi5 : ahci
[    4.621728] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43
[    4.622270] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43
[    4.622814] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43
[    4.623356] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43
[    4.623900] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43
[    4.624440] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43
[    4.625012] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.628395] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
[    4.629059] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ
[    4.629466] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP
[    4.629875] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3
[    4.630247] ahci: SSS flag set, parallel bus scan disabled
[    4.630640] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
[    4.631203] ahci 0000:06:00.0: flags: 64bit stag led slum part 
[    4.631576] ahci 0000:06:00.0: setting latency timer to 64
[    4.632838] scsi6 : ahci
[    4.633237] scsi7 : ahci
[    4.633640] scsi8 : ahci
[    4.634015] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16
[    4.634557] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16
[    4.635101] ata9: DUMMY
[    4.637359] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    4.637773] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    4.638217] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k
[    4.638585] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[    4.638985] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0)
[    4.639553] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    4.639968] e1000e 0000:00:19.0: setting latency timer to 64
[    4.640437] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    4.831156] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54
[    4.831724] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    4.832160] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF
[    4.832640] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k
[    4.833031] Copyright (c) 2007-2011 Intel Corporation.
[    4.833447] Intel(R) Virtual Function Network Driver - version 2.0.0-k
[    4.833843] Copyright (c) 2009 - 2010 Intel Corporation.
[    4.834271] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k
[    4.834825] ixgbe: Copyright (c) 1999-2011 Intel Corporation.
[    4.835266] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[    4.835682] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[    4.836401] jme: JMicron JMC2XX ethernet driver version 1.0.8
[    4.836840] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    4.837215] e100: Copyright(c) 1999-2006 Intel Corporation
[    4.837875] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
[    4.838492] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011)
[    4.839146] sky2: driver version 1.29
[    4.840429] tun: Universal TUN/TAP device driver, 1.6
[    4.840771] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    4.841418] usbcore: registered new interface driver catc
[    4.841772] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[    4.842186] usbcore: registered new interface driver kaweth
[    4.842543] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[    4.843138] usbcore: registered new interface driver pegasus
[    4.843499] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[    4.843956] usbcore: registered new interface driver rtl8150
[    4.844367] usbcore: registered new interface driver asix
[    4.844770] usbcore: registered new interface driver cdc_ether
[    4.845182] usbcore: registered new interface driver cdc_eem
[    4.845591] usbcore: registered new interface driver dm9601
[    4.846007] usbcore: registered new interface driver smsc75xx
[    4.846422] usbcore: registered new interface driver smsc95xx
[    4.846839] usbcore: registered new interface driver gl620a
[    4.847246] usbcore: registered new interface driver net1080
[    4.847659] usbcore: registered new interface driver plusb
[    4.848062] usbcore: registered new interface driver rndis_host
[    4.848479] usbcore: registered new interface driver cdc_subset
[    4.848901] usbcore: registered new interface driver zaurus
[    4.849306] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    4.849903] usbcore: registered new interface driver int51x1
[    4.850263] cdc_ncm: 04-Aug-2011
[    4.850578] usbcore: registered new interface driver cdc_ncm
[    4.850944] netconsole: local port 6665
[    4.851235] netconsole: local IP 10.0.0.0
[    4.851534] netconsole: interface 'eth0'
[    4.851831] netconsole: remote port 6666
[    4.852126] netconsole: remote IP 192.168.1.1
[    4.852437] netconsole: remote ethernet address 00:30:48:fe:19:95
[    4.852815] netconsole: device eth0 not up yet, forcing it
[    4.929667] ata6: SATA link down (SStatus 0 SControl 300)
[    4.930041] ata3: SATA link down (SStatus 0 SControl 300)
[    4.930419] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    4.930822] ata5: SATA link down (SStatus 0 SControl 300)
[    4.931193] ata4: SATA link down (SStatus 0 SControl 300)
[    4.939678] ata7: SATA link down (SStatus 0 SControl 300)
[    4.948144] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    4.971428] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
[    4.971793] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    4.998734] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    5.029731] ata1.00: configured for UDMA/133
[    5.030222] scsi 0:0:0:0: Direct-Access     ATA      ST3320620AS      3.AA PQ: 0 ANSI: 5
[    5.031145] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    5.031782] sd 0:0:0:0: [sda] Write Protect is off
[    5.032111] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.032475] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.121766]  sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 >
[    5.123005] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.286787] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.362521] ata2.00: ATAPI: PLEXTOR DVDR   PX-712A, 1.07, max UDMA/33
[    5.362918] ata2.00: applying bridge limits
[    5.393753] ata2.00: configured for UDMA/33
[    5.395032] scsi 1:0:0:0: CD-ROM            PLEXTOR  DVDR   PX-712A   1.07 PQ: 0 ANSI: 5
[    5.700712] ata8: SATA link down (SStatus 0 SControl 300)
[    7.755673] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[    7.758015] console [netcon0] enabled
[    7.758303] netconsole: network logging started
[    7.758683] Fusion MPT base driver 3.04.19
[    7.758996] Copyright (c) 1999-2008 LSI Corporation
[    7.759341] Fusion MPT SPI Host driver 3.04.19
[    7.759746] Fusion MPT FC Host driver 3.04.19
[    7.760147] Fusion MPT SAS Host driver 3.04.19
[    7.760551] Fusion MPT misc device (ioctl) driver 3.04.19
[    7.760983] mptctl: Registered with Fusion MPT base driver
[    7.761342] mptctl: /dev/mptctl @ (major,minor=10,220)
[    7.761791] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.762188] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96
[    7.762604] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0)
[    7.763186] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    7.763619] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    7.763995] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    7.764412] /c/wfg/linux/drivers/usb/core/inode.c: creating file 'devices'
[    7.764841] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.765254] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    7.765810] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[    7.766413] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch
[    7.767070] ehci_hcd 0000:00:1a.7: debug port 1
[    7.767395] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.771881] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[    7.772286] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[    7.772672] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000
[    7.773042] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.777524] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[    7.783762] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    7.784236] usb usb1: default language 0x0409
[    7.784562] usb usb1: udev 1, busnum 1, minor = 0
[    7.784896] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.785301] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.785842] usb usb1: Product: EHCI Host Controller
[    7.786176] usb usb1: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ ehci_hcd
[    7.786581] usb usb1: SerialNumber: 0000:00:1a.7
[    7.787032] usb usb1: usb_probe_device
[    7.787329] usb usb1: configuration #1 chosen from 1 choice
[    7.787714] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    7.788164] hub 1-0:1.0: usb_probe_interface
[    7.788480] hub 1-0:1.0: usb_probe_interface - got id
[    7.788826] hub 1-0:1.0: USB hub found
[    7.789124] hub 1-0:1.0: 6 ports detected
[    7.789426] hub 1-0:1.0: standalone hub
[    7.789722] hub 1-0:1.0: no power switching (usb 1.0)
[    7.790067] hub 1-0:1.0: individual port over-current protection
[    7.790444] hub 1-0:1.0: power on to power good time: 20ms
[    7.790823] hub 1-0:1.0: local power source is good
[    7.791160] hub 1-0:1.0: trying to enable port power on non-switchable hub
[    7.791617] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.792142] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0)
[    7.792717] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    7.793152] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    7.793524] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    7.793881] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002'
[    7.794281] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    7.794838] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[    7.795441] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch
[    7.799061] ehci_hcd 0000:00:1d.7: debug port 1
[    7.799385] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.803864] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    7.804269] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[    7.804656] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000
[    7.805025] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.809507] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[    7.815761] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    7.816175] usb usb2: default language 0x0409
[    7.816500] usb usb2: udev 1, busnum 2, minor = 128
[    7.816839] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    7.817244] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.817784] usb usb2: Product: EHCI Host Controller
[    7.818117] usb usb2: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ ehci_hcd
[    7.818522] usb usb2: SerialNumber: 0000:00:1d.7
[    7.818966] usb usb2: usb_probe_device
[    7.819261] usb usb2: configuration #1 chosen from 1 choice
[    7.819628] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[    7.820062] hub 2-0:1.0: usb_probe_interface
[    7.820375] hub 2-0:1.0: usb_probe_interface - got id
[    7.820715] hub 2-0:1.0: USB hub found
[    7.821015] hub 2-0:1.0: 6 ports detected
[    7.821318] hub 2-0:1.0: standalone hub
[    7.821613] hub 2-0:1.0: no power switching (usb 1.0)
[    7.821957] hub 2-0:1.0: individual port over-current protection
[    7.822333] hub 2-0:1.0: power on to power good time: 20ms
[    7.822695] hub 2-0:1.0: local power source is good
[    7.823032] hub 2-0:1.0: trying to enable port power on non-switchable hub
[    7.823486] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.824040] uhci_hcd: USB Universal Host Controller Interface driver
[    7.824480] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    7.824910] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    7.825280] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    7.825635] /c/wfg/linux/drivers/usb/core/inode.c: creating file '003'
[    7.826039] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    7.826591] uhci_hcd 0000:00:1a.0: detected 2 ports
[    7.826932] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[    7.827333] uhci_hcd 0000:00:1a.0: Performing full reset
[    7.827695] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[    7.828069] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0
[    7.828490] usb usb3: default language 0x0409
[    7.828821] usb usb3: udev 1, busnum 3, minor = 256
[    7.829155] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    7.829560] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.830100] usb usb3: Product: UHCI Host Controller
[    7.830435] usb usb3: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd
[    7.830843] usb usb3: SerialNumber: 0000:00:1a.0
[    7.831294] usb usb3: usb_probe_device
[    7.831589] usb usb3: configuration #1 chosen from 1 choice
[    7.831961] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[    7.832396] hub 3-0:1.0: usb_probe_interface
[    7.832710] hub 3-0:1.0: usb_probe_interface - got id
[    7.833055] hub 3-0:1.0: USB hub found
[    7.833353] hub 3-0:1.0: 2 ports detected
[    7.833656] hub 3-0:1.0: standalone hub
[    7.833957] hub 3-0:1.0: no power switching (usb 1.0)
[    7.834298] hub 3-0:1.0: individual port over-current protection
[    7.834674] hub 3-0:1.0: power on to power good time: 2ms
[    7.835038] hub 3-0:1.0: local power source is good
[    7.835374] hub 3-0:1.0: trying to enable port power on non-switchable hub
[    7.835809] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.836261] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0
[    7.836703] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0)
[    7.837280] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    7.837703] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    7.838077] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    7.838430] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004'
[    7.838835] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    7.839389] uhci_hcd 0000:00:1a.1: detected 2 ports
[    7.839726] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[    7.840131] uhci_hcd 0000:00:1a.1: Performing full reset
[    7.840493] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[    7.840884] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0
[    7.841290] usb usb4: default language 0x0409
[    7.841615] usb usb4: udev 1, busnum 4, minor = 384
[    7.841953] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    7.842359] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.842898] usb usb4: Product: UHCI Host Controller
[    7.843232] usb usb4: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd
[    7.843637] usb usb4: SerialNumber: 0000:00:1a.1
[    7.844079] usb usb4: usb_probe_device
[    7.844375] usb usb4: configuration #1 chosen from 1 choice
[    7.844745] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[    7.845178] hub 4-0:1.0: usb_probe_interface
[    7.845492] hub 4-0:1.0: usb_probe_interface - got id
[    7.845836] hub 4-0:1.0: USB hub found
[    7.846133] hub 4-0:1.0: 2 ports detected
[    7.846436] hub 4-0:1.0: standalone hub
[    7.846731] hub 4-0:1.0: no power switching (usb 1.0)
[    7.847075] hub 4-0:1.0: individual port over-current protection
[    7.847451] hub 4-0:1.0: power on to power good time: 2ms
[    7.847813] hub 4-0:1.0: local power source is good
[    7.848147] hub 4-0:1.0: trying to enable port power on non-switchable hub
[    7.848579] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.849036] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1
[    7.849473] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    7.849901] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    7.850273] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    7.850628] /c/wfg/linux/drivers/usb/core/inode.c: creating file '005'
[    7.851034] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    7.851586] uhci_hcd 0000:00:1a.2: detected 2 ports
[    7.851926] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
[    7.852328] uhci_hcd 0000:00:1a.2: Performing full reset
[    7.852689] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
[    7.853079] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0
[    7.853489] usb usb5: default language 0x0409
[    7.853818] usb usb5: udev 1, busnum 5, minor = 512
[    7.854155] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    7.854561] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.855103] usb usb5: Product: UHCI Host Controller
[    7.855437] usb usb5: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd
[    7.855846] usb usb5: SerialNumber: 0000:00:1a.2
[    7.856286] usb usb5: usb_probe_device
[    7.856581] usb usb5: configuration #1 chosen from 1 choice
[    7.856952] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[    7.857385] hub 5-0:1.0: usb_probe_interface
[    7.857699] hub 5-0:1.0: usb_probe_interface - got id
[    7.858042] hub 5-0:1.0: USB hub found
[    7.858340] hub 5-0:1.0: 2 ports detected
[    7.858642] hub 5-0:1.0: standalone hub
[    7.858940] hub 5-0:1.0: no power switching (usb 1.0)
[    7.859282] hub 5-0:1.0: individual port over-current protection
[    7.859657] hub 5-0:1.0: power on to power good time: 2ms
[    7.860020] hub 5-0:1.0: local power source is good
[    7.860354] hub 5-0:1.0: trying to enable port power on non-switchable hub
[    7.860788] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.861236] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2
[    7.861674] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    7.862101] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    7.862472] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    7.862830] /c/wfg/linux/drivers/usb/core/inode.c: creating file '006'
[    7.863234] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    7.863793] uhci_hcd 0000:00:1d.0: detected 2 ports
[    7.864130] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[    7.864532] uhci_hcd 0000:00:1d.0: Performing full reset
[    7.864897] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[    7.865268] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080
[    7.865673] usb usb6: default language 0x0409
[    7.866001] usb usb6: udev 1, busnum 6, minor = 640
[    7.866335] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    7.866739] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.867280] usb usb6: Product: UHCI Host Controller
[    7.867616] usb usb6: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd
[    7.868025] usb usb6: SerialNumber: 0000:00:1d.0
[    7.868465] usb usb6: usb_probe_device
[    7.868766] usb usb6: configuration #1 chosen from 1 choice
[    7.869132] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[    7.869566] hub 6-0:1.0: usb_probe_interface
[    7.869883] hub 6-0:1.0: usb_probe_interface - got id
[    7.870225] hub 6-0:1.0: USB hub found
[    7.870522] hub 6-0:1.0: 2 ports detected
[    7.870829] hub 6-0:1.0: standalone hub
[    7.871125] hub 6-0:1.0: no power switching (usb 1.0)
[    7.871468] hub 6-0:1.0: individual port over-current protection
[    7.871848] hub 6-0:1.0: power on to power good time: 2ms
[    7.872208] hub 6-0:1.0: local power source is good
[    7.872544] hub 6-0:1.0: trying to enable port power on non-switchable hub
[    7.872982] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.873441] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0
[    7.873872] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    7.874297] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    7.874668] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    7.875025] /c/wfg/linux/drivers/usb/core/inode.c: creating file '007'
[    7.875425] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    7.875982] uhci_hcd 0000:00:1d.1: detected 2 ports
[    7.879292] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[    7.879693] uhci_hcd 0000:00:1d.1: Performing full reset
[    7.880059] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[    7.880430] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
[    7.880846] usb usb7: default language 0x0409
[    7.881171] usb usb7: udev 1, busnum 7, minor = 768
[    7.881506] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    7.881914] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.882451] usb usb7: Product: UHCI Host Controller
[    7.882789] usb usb7: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd
[    7.883193] usb usb7: SerialNumber: 0000:00:1d.1
[    7.883635] usb usb7: usb_probe_device
[    7.883935] usb usb7: configuration #1 chosen from 1 choice
[    7.884302] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[    7.884735] hub 7-0:1.0: usb_probe_interface
[    7.885052] hub 7-0:1.0: usb_probe_interface - got id
[    7.885393] hub 7-0:1.0: USB hub found
[    7.885689] hub 7-0:1.0: 2 ports detected
[    7.885994] hub 7-0:1.0: standalone hub
[    7.886290] hub 7-0:1.0: no power switching (usb 1.0)
[    7.886630] hub 7-0:1.0: individual port over-current protection
[    7.887009] hub 7-0:1.0: power on to power good time: 2ms
[    7.887367] hub 7-0:1.0: local power source is good
[    7.887701] hub 7-0:1.0: trying to enable port power on non-switchable hub
[    7.888136] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.888595] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1
[    7.889023] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    7.889447] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    7.889822] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    7.890173] /c/wfg/linux/drivers/usb/core/inode.c: creating file '008'
[    7.890573] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    7.891149] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0  ACK POWER sig=j CSC CONNECT
[    7.891753] hub 1-0:1.0: port 1: status 0501 change 0001
[    7.891779] uhci_hcd 0000:00:1d.2: detected 2 ports
[    7.891784] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[    7.891786] uhci_hcd 0000:00:1d.2: Performing full reset
[    7.891799] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[    7.891807] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
[    7.891889] usb usb8: default language 0x0409
[    7.891903] usb usb8: udev 1, busnum 8, minor = 896
[    7.891904] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    7.891906] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.891909] usb usb8: Product: UHCI Host Controller
[    7.891910] usb usb8: Manufacturer: Linux 3.1.0-rc1-no-maxpause+ uhci_hcd
[    7.891912] usb usb8: SerialNumber: 0000:00:1d.2
[    7.892091] usb usb8: usb_probe_device
[    7.892095] usb usb8: configuration #1 chosen from 1 choice
[    7.892105] usb usb8: adding 8-0:1.0 (config #1, interface 0)
[    7.892190] hub 8-0:1.0: usb_probe_interface
[    7.892192] hub 8-0:1.0: usb_probe_interface - got id
[    7.892194] hub 8-0:1.0: USB hub found
[    7.892201] hub 8-0:1.0: 2 ports detected
[    7.892202] hub 8-0:1.0: standalone hub
[    7.892204] hub 8-0:1.0: no power switching (usb 1.0)
[    7.892205] hub 8-0:1.0: individual port over-current protection
[    7.892207] hub 8-0:1.0: power on to power good time: 2ms
[    7.892215] hub 8-0:1.0: local power source is good
[    7.892217] hub 8-0:1.0: trying to enable port power on non-switchable hub
[    7.892256] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.892387] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2
[    7.892562] Initializing USB Mass Storage driver...
[    7.892661] usbcore: registered new interface driver usb-storage
[    7.892663] USB Mass Storage support registered.
[    7.892814] usbcore: registered new interface driver libusual
[    7.892892] usbcore: registered new interface driver ums-alauda
[    7.892970] usbcore: registered new interface driver ums-cypress
[    7.893035] usbcore: registered new interface driver ums-datafab
[    7.893110] usbcore: registered new interface driver ums-freecom
[    7.893183] usbcore: registered new interface driver ums-isd200
[    7.893255] usbcore: registered new interface driver ums-jumpshot
[    7.893320] usbcore: registered new interface driver ums-karma
[    7.893385] usbcore: registered new interface driver ums-onetouch
[    7.893459] usbcore: registered new interface driver ums-sddr09
[    7.893529] usbcore: registered new interface driver ums-sddr55
[    7.893606] usbcore: registered new interface driver ums-usbat
[    7.893754] usbcore: registered new interface driver usbserial
[    7.893828] USB Serial support registered for generic
[    7.893921] usbcore: registered new interface driver usbserial_generic
[    7.893924] usbserial: USB Serial Driver core
[    7.893989] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[    7.894063] usbcore: registered new interface driver belkin
[    7.894065] belkin_sa: v1.3:USB Belkin Serial converter driver
[    7.894123] USB Serial support registered for MCT U232
[    7.894202] usbcore: registered new interface driver mct_u232
[    7.894203] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
[    7.894436] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    7.911576] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0  ACK POWER sig=k CSC CONNECT
[    7.912213] hub 1-0:1.0: port 2: status 0501 change 0001
[    7.912595] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0  ACK POWER sig=j CSC CONNECT
[    7.912666] serio: i8042 KBD port at 0x60,0x64 irq 1
[    7.912686] serio: i8042 AUX port at 0x60,0x64 irq 12
[    7.913085] mousedev: PS/2 mouse device common for all mice
[    7.914268] hub 1-0:1.0: port 4: status 0501 change 0001
[    7.914492] rtc_cmos 00:02: RTC can wake from S4
[    7.914726] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    7.914762] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    7.914814] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[    7.914986] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460)
[    7.915088] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    7.915091] iTCO_vendor_support: vendor-support=0
[    7.915093] SoftDog: cannot register miscdev on minor=130 (err=-16)
[    7.915102] md: linear personality registered for level -1
[    7.915103] md: raid0 personality registered for level 0
[    7.915104] md: raid1 personality registered for level 1
[    7.915106] md: raid10 personality registered for level 10
[    7.915107] md: raid6 personality registered for level 6
[    7.915109] md: raid5 personality registered for level 5
[    7.915110] md: raid4 personality registered for level 4
[    7.915111] md: multipath personality registered for level -4
[    7.915113] md: faulty personality registered for level -5
[    7.920749] device-mapper: uevent: version 1.0.3
[    7.921192] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
[    7.921914] device-mapper: multipath: version 1.3.0 loaded
[    7.922279] device-mapper: multipath round-robin: version 1.0.0 loaded
[    7.922671] device-mapper: multipath queue-length: version 0.1.0 loaded
[    7.922790] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[    7.923425] device-mapper: multipath service-time: version 0.2.0 loaded
[    7.923920] device-mapper: dm-log-userspace: version 1.1.0 loaded
[    7.925420] cpuidle: using governor ladder
[    7.928053] cpuidle: using governor menu
[    7.928537] usbcore: registered new interface driver usbhid
[    7.928902] usbhid: USB HID core driver
[    7.929510] dell_wmi: No known WMI GUID found
[    7.929858] acer_wmi: Acer Laptop ACPI-WMI Extras
[    7.930215] acer_wmi: No or unsupported WMI interface, unable to load
[    7.930961] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0)
[    7.931561] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    7.932188] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[    7.932607] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[    7.933027] ALSA hda_intel.c:2598 chipset global capabilities = 0x4401
[    7.933462] ALSA hda_intel.c:1091 Clearing TCSEL
[    7.935820] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00
[    7.936191] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00
[    7.941793] ALSA hda_intel.c:945 codec_mask = 0x4
[    7.942307] ALSA hda_intel.c:1392 codec #2 probed OK
[    7.947837] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00
[    7.948197] ALSA hda_codec.c:3955 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO)
[    7.948815] hda_codec: ALC889: SKU not ready 0x411111f0
[    7.949369] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2
[    7.952878] ALSA hda_codec.c:2339 Cannot find slave Side Playback Volume, skipped
[    7.953424] ALSA hda_codec.c:2339 Cannot find slave Headphone Playback Volume, skipped
[    7.953995] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Volume, skipped
[    7.954542] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Volume, skipped
[    7.955112] ALSA hda_codec.c:2339 Cannot find slave Side Playback Switch, skipped
[    7.955661] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Switch, skipped
[    7.956213] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Switch, skipped
[    7.957502] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3
[    7.958457] ALSA device list:
[    7.958721]   #0: HDA Intel at 0xf7f00000 irq 45
[    7.959048] oprofile: using NMI interrupt.
[    7.959449] netem: version 1.3
[    7.959716] Netfilter messages via NETLINK v0.30.
[    7.960079] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    7.960786] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    7.961063] ctnetlink v0.93: registering with nfnetlink.
[    7.961120] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    7.961121] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    7.962323] xt_time: kernel timezone is -0000
[    7.963975] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.967382] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[    7.967796] arp_tables: (C) 2002 David S. Miller
[    7.968152] TCP bic registered
[    7.968418] TCP cubic registered
[    7.968688] TCP westwood registered
[    7.968972] TCP highspeed registered
[    7.969255] TCP hybla registered
[    7.969527] TCP htcp registered
[    7.969802] TCP vegas registered
[    7.970073] TCP veno registered
[    7.970340] TCP scalable registered
[    7.970619] TCP lp registered
[    7.970885] TCP yeah registered
[    7.971152] TCP illinois registered
[    7.971432] Initializing XFRM netlink socket
[    7.971761] NET: Registered protocol family 17
[    7.972086] NET: Registered protocol family 15
[    7.972556] Bridge firewalling registered
[    7.972806] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    7.973264] Ebtables v2.0 registered
[    7.973638] 
[    7.973639] printing PIC contents
[    7.974156] ... PIC  IMR: ffff
[    7.974448] ... PIC  IRR: 0c21
[    7.974742] ... PIC  ISR: 0000
[    7.975066] ... PIC ELCR: 0c20
[    7.975387] printing local APIC contents on CPU#0/0:
[    7.975722] ... APIC ID:      00000000 (0)
[    7.976023] ... APIC VERSION: 00060015
[    7.976312] ... APIC TASKPRI: 00000000 (00)
[    7.976617] ... APIC PROCPRI: 00000000
[    7.976905] ... APIC LDR: 01000000
[    7.977181] ... APIC DFR: ffffffff
[    7.977456] ... APIC SPIV: 000001ff
[    7.977734] ... APIC ISR field:
[    7.978001] 0000000000000000000000000000000000000000000000000000000000000000
[    7.978683] ... APIC TMR field:
[    7.978949] 0000000000000000000000000000000000020000000000000000000000000000
[    7.979631] ... APIC IRR field:
[    7.979897] 0000000000010000000000000000000000000200000000000000000000000000
[    7.980577] ... APIC ESR: 00000000
[    7.980855] ... APIC ICR: 000000ef
[    7.981131] ... APIC ICR2: 07000000
[    7.981410] ... APIC LVTT: 000000ef
[    7.981688] ... APIC LVTPC: 00000400
[    7.981970] ... APIC LVT0: 00010700
[    7.982249] ... APIC LVT1: 00000400
[    7.982529] ... APIC LVTERR: 000000fe
[    7.982814] ... APIC TMICT: 00000000
[    7.983097] ... APIC TMCCT: 00000000
[    7.983379] ... APIC TDCR: 00000003
[    7.983658] 
[    7.983864] number of MP IRQ sources: 15.
[    7.984191] number of IO-APIC #8 registers: 24.
[    7.984537] testing the IO APIC.......................
[    7.984893] 
[    7.985099] IO APIC #8......
[    7.985357] .... register #00: 08000000
[    7.985651] .......    : physical APIC id: 08
[    7.985968] .......    : Delivery Type: 0
[    7.986269] .......    : LTS          : 0
[    7.986569] .... register #01: 00170020
[    7.986913] .......     : max redirection entries: 17
[    7.987276] .......     : PRQ implemented: 0
[    7.987584] .......     : IO APIC version: 20
[    7.987856] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    7.988320] .... IRQ redirection table:
[    7.988613]  NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
[    7.988980]  00 00  1    0    0   0   0    0    0    00
[    7.989417]  01 00  0    0    0   0   0    0    0    31
[    7.989863]  02 00  0    0    0   0   0    0    0    30
[    7.990309]  03 00  0    0    0   0   0    0    0    33
[    7.990748]  04 00  0    0    0   0   0    0    0    34
[    7.991208]  05 00  0    0    0   0   0    0    0    35
[    7.991648]  06 00  1    0    0   0   0    0    0    36
[    7.991886] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    7.992507]  07 00  0    0    0   0   0    0    0    37
[    7.992959]  08 00  0    0    0   0   0    0    0    38
[    7.993396]  09 00  0    1    0   0   0    0    0    39
[    7.993808]  0a 00  0    0    0   0   0    0    0    3A
[    7.994190]  0b 00  0    0    0   0   0    0    0    3B
[    7.994571]  0c 00  0    0    0   0   0    0    0    3C
[    7.994955]  0d 00  0    0    0   0   0    0    0    3D
[    7.995336]  0e 00  0    0    0   0   0    0    0    3E
[    7.995718]  0f 00  0    0    0   0   0    0    0    3F
[    7.996126]  10 00  0    1    0   1   0    0    0    29
[    7.996507]  11 00  1    1    0   1   0    0    0    41
[    7.996898]  12 00  0    1    0   1   0    0    0    91
[    7.997280]  13 00  0    1    0   1   0    0    0    61
[    7.997661]  14 00  1    1    0   1   0    0    0    71
[    7.998048]  15 00  0    1    0   1   0    0    0    A1
[    7.998430]  16 00  1    1    0   1   0    0    0    A9
[    7.998817]  17 00  0    1    0   1   0    0    0    99
[    7.999196] IRQ to pin mappings:
[    7.999467] IRQ0 -> 0:2
[    7.999782] IRQ1 -> 0:1
[    8.000095] IRQ3 -> 0:3
[    8.000404] IRQ4 -> 0:4
[    8.000714] IRQ5 -> 0:5
[    8.001044] IRQ6 -> 0:6
[    8.001353] IRQ7 -> 0:7
[    8.001663] IRQ8 -> 0:8
[    8.001980] IRQ9 -> 0:9
[    8.002290] IRQ10 -> 0:10
[    8.002607] IRQ11 -> 0:11
[    8.002953] IRQ12 -> 0:12
[    8.003270] IRQ13 -> 0:13
[    8.003587] IRQ14 -> 0:14
[    8.003945] IRQ15 -> 0:15
[    8.004261] IRQ16 -> 0:16
[    8.004579] IRQ17 -> 0:17
[    8.004898] IRQ18 -> 0:18
[    8.005216] IRQ19 -> 0:19
[    8.005533] IRQ20 -> 0:20
[    8.005852] IRQ21 -> 0:21
[    8.006170] IRQ22 -> 0:22
[    8.006486] IRQ23 -> 0:23
[    8.006805] .................................... done.
[    8.007520] PM: Hibernation image not present or could not be loaded.
[    8.007945] registered taskstats version 1
[    8.008996]   Magic number: 7:444:500
[    8.009490] rtc_cmos 00:02: setting system clock to 2011-08-17 21:27:53 UTC (1313616473)
[    8.019841] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000
[    8.020205] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[    8.023916] IP-Config: Complete:
[    8.024221]      device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1,
[    8.024854]      host=fat, domain=, nis-domain=(none),
[    8.025258]      bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath=
[    8.071060] ehci_hcd 0000:00:1a.7: port 1 high speed
[    8.071425] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    8.122907] usb 1-1: new high speed USB device number 2 using ehci_hcd
[    8.176064] ehci_hcd 0000:00:1a.7: port 1 high speed
[    8.176402] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    8.246711] usb 1-1: default language 0x0409
[    8.253637] usb 1-1: udev 2, busnum 1, minor = 1
[    8.253974] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780
[    8.254375] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    8.254851] usb 1-1: Product: AX88178 
[    8.255143] usb 1-1: Manufacturer: ASIX Elec. Corp.
[    8.255475] usb 1-1: SerialNumber: 000013
[    8.255936] usb 1-1: usb_probe_device
[    8.256229] usb 1-1: configuration #1 chosen from 1 choice
[    8.257211] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[    8.258181] asix 1-1:1.0: usb_probe_interface
[    8.258497] asix 1-1:1.0: usb_probe_interface - got id
[    8.951856] usb usb8: suspend_rh (auto-stop)
[    8.951859] usb usb5: suspend_rh (auto-stop)
[    8.951881] usb usb6: suspend_rh (auto-stop)
[    8.951901] usb usb7: suspend_rh (auto-stop)
[    8.951921] usb usb3: suspend_rh (auto-stop)
[    8.951940] usb usb4: suspend_rh (auto-stop)
[    8.970179] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83
[    8.970887] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002'
[    8.971312] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[    8.971366] md: Waiting for all devices to be available before autodetect
[    8.971368] md: If you don't use raid, use raid=noautodetect
[    8.971743] md: Autodetecting RAID arrays.
[    8.971744] md: Scanned 0 and added 0 devices.
[    8.971745] md: autorun ...
[    8.971746] md: ... autorun DONE.
[    8.973627] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion
[    8.974018] usb usb3: wakeup_rh (auto-start)
[    8.980183] VFS: Mounted root (nfs filesystem) on device 0:15.
[    8.980572] debug: unmapping init memory ffffffff81ebe000..ffffffff82172000
[    9.024851] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0  ACK POWER OWNER sig=se0 CSC
[    9.025479] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s
[    9.077096] ehci_hcd 0000:00:1a.7: port 4 high speed
[    9.077433] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    9.128826] usb 1-4: new high speed USB device number 4 using ehci_hcd
[    9.180100] ehci_hcd 0000:00:1a.7: port 4 high speed
[    9.180437] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    9.754483] stty used greatest stack depth: 4544 bytes left
[    9.849972] uname used greatest stack depth: 3872 bytes left
[    9.862122] sed used greatest stack depth: 3728 bytes left
[    9.909394] sh used greatest stack depth: 3696 bytes left
[    9.922107] mountpoint used greatest stack depth: 3600 bytes left
[   10.182224] usb 1-4: default language 0x0409
[   10.184081] usb 1-4: udev 4, busnum 1, minor = 3
[   10.184410] usb 1-4: New USB device found, idVendor=1307, idProduct=0165
[   10.184811] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   10.185240] usb 1-4: Product: USB Mass Storage Device
[   10.185583] usb 1-4: Manufacturer: Teclast Technology
[   10.185935] usb 1-4: SerialNumber: 0000000000020D
[   10.186389] usb 1-4: usb_probe_device
[   10.186680] usb 1-4: configuration #1 chosen from 1 choice
[   10.187159] usb 1-4: adding 1-4:1.0 (config #1, interface 0)
[   10.187566] usb-storage 1-4:1.0: usb_probe_interface
[   10.187922] usb-storage 1-4:1.0: usb_probe_interface - got id
[   10.188458] scsi9 : usb-storage 1-4:1.0
[   10.188966] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004'
[   10.189389] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
[   10.189753] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00
[   10.190155] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
[   10.293879] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
[   10.395860] usb 3-2: new low speed USB device number 2 using uhci_hcd
[   10.399392] usb 3-2: uhci_result_common: failed with status 440000
[   10.403388] usb 3-2: uhci_result_common: failed with status 440000
[   10.407387] usb 3-2: uhci_result_common: failed with status 440000
[   10.508912] usb 3-2: device descriptor read/64, error -71
[   10.613395] usb 3-2: uhci_result_common: failed with status 440000
[   10.617394] usb 3-2: uhci_result_common: failed with status 440000
[   10.621393] usb 3-2: uhci_result_common: failed with status 440000
[   10.722921] usb 3-2: device descriptor read/64, error -71
[   10.925882] usb 3-2: new low speed USB device number 3 using uhci_hcd
[   10.929409] usb 3-2: uhci_result_common: failed with status 440000
[   10.933428] usb 3-2: uhci_result_common: failed with status 440000
[   10.937424] usb 3-2: uhci_result_common: failed with status 440000
[   11.040903] usb 3-2: device descriptor read/64, error -71
[   11.145417] usb 3-2: uhci_result_common: failed with status 440000
[   11.149414] usb 3-2: uhci_result_common: failed with status 440000
[   11.153415] usb 3-2: uhci_result_common: failed with status 440000
[   11.189970] scsi 9:0:0:0: Direct-Access     Teclast  CoolFlash        0.00 PQ: 0 ANSI: 2
[   11.254887] usb 3-2: device descriptor read/64, error -71
[   11.300627] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB)
[   11.301840] sd 9:0:0:0: [sdb] Write Protect is off
[   11.302188] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00
[   11.303221] sd 9:0:0:0: [sdb] Asking for cache data failed
[   11.303584] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[   11.308217] sd 9:0:0:0: [sdb] Asking for cache data failed
[   11.308578] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[   11.442853]  sdb: sdb1 sdb2 sdb3
[   11.446582] sd 9:0:0:0: [sdb] Asking for cache data failed
[   11.446954] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[   11.447336] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[   11.458925] usb 3-2: new low speed USB device number 4 using uhci_hcd
[   11.462427] usb 3-2: uhci_result_common: failed with status 440000
[   11.666432] usb 3-2: uhci_result_common: failed with status 440000
[   11.866913] usb 3-2: device not accepting address 4, error -71
[   11.969014] usb 3-2: new low speed USB device number 5 using uhci_hcd
[   11.972501] usb 3-2: uhci_result_common: failed with status 440000
[   12.177456] usb 3-2: uhci_result_common: failed with status 440000
[   12.377947] usb 3-2: device not accepting address 5, error -71
[   12.378356] hub 3-0:1.0: unable to enumerate USB device on port 2
[   12.378769] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   12.379170] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004
[   12.379557] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
[   12.442001] fstab_import used greatest stack depth: 3344 bytes left
[   14.718732] EXT4-fs (sda5): recovery complete
[   14.719194] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   16.067003] mount.nfs used greatest stack depth: 3152 bytes left
[   18.014005] XFS (sda7): Mounting Filesystem
[   18.081710] XFS (sda7): Ending clean mount