[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Linux version 3.1.0-rc1+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #203 SMP Wed Aug 17 12:15:08 CST 2011 [ 0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1+ [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009cc00 (usable) [ 0.000000] BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bcda4000 (usable) [ 0.000000] BIOS-e820: 00000000bcda4000 - 00000000bcfdd000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bcfdd000 - 00000000bf6bd000 (usable) [ 0.000000] BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved) [ 0.000000] BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable) [ 0.000000] BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable) [ 0.000000] BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable) [ 0.000000] BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI 2.5 present. [ 0.000000] DMI: /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008 [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-DFFFF write-protect [ 0.000000] E0000-FFFFF uncachable [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F80000000 write-back [ 0.000000] 1 base 080000000 mask FC0000000 write-back [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scan SMP from ffff880000000000 for 1024 bytes. [ 0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes. [ 0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0 [ 0.000000] mpc: ff4d0-ff6a8 [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf800000 [ 0.000000] 0000000000 - 00bf800000 page 4k [ 0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000 [ 0.000000] log_buf_len: 8388608 [ 0.000000] early log buf free: 258317(98%) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL ) [ 0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL DX58SO 0000084F 01000013) [ 0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560) [ 0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610) [ 0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: FACS 00000000bf726000 00040 [ 0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL SSDT PM 0000084F MSFT 0100000D) [ 0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL DX58SO 0000084F MSFT 0100000D) [ 0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL PerfTune 0000084F MSFT 0100000D) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-00000000bf800000 [ 0.000000] Initmem setup node 0 0000000000000000-00000000bf800000 [ 0.000000] NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff] [ 0.000000] [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800b9c00000-ffff8800bc5fffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009c [ 0.000000] 0: 0x00000100 -> 0x000bcda4 [ 0.000000] 0: 0x000bcfdd -> 0x000bf6bd [ 0.000000] 0: 0x000bf6bf -> 0x000bf714 [ 0.000000] 0: 0x000bf7bf -> 0x000bf7e7 [ 0.000000] 0: 0x000bf7ff -> 0x000bf800 [ 0.000000] On node 0 totalpages: 783502 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 5 pages reserved [ 0.000000] DMA zone: 3919 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 10668 pages used for memmap [ 0.000000] DMA32 zone: 768854 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] mapped APIC to ffffffffff5fb000 ( fee00000) [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09 [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01 [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07 [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08 [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e [ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs [ 0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000) [ 0.000000] nr_irqs_gsi: 40 [ 0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000 [ 0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bcda4000 - 00000000bcfdd000 [ 0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000 [ 0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915008 r8192 d22400 u2097152 [ 0.000000] pcpu-alloc: s1915008 r8192 d22400 u2097152 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 [ 0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 772773 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1+ [ 0.000000] sysrq: sysrq always enabled. [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Memory: 3019044k/3137536k available (9445k kernel code, 3528k absent, 114964k reserved, 5641k data, 2768k init) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU debugfs-based tracing is enabled. [ 0.000000] NR_IRQS:4352 nr_irqs:808 16 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [ttyS0] enabled [ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000000] ... MAX_LOCK_DEPTH: 48 [ 0.000000] ... MAX_LOCKDEP_KEYS: 8191 [ 0.000000] ... CLASSHASH_SIZE: 4096 [ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384 [ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768 [ 0.000000] ... CHAINHASH_SIZE: 16384 [ 0.000000] memory used by lock dependency info: 6335 kB [ 0.000000] per task-struct memory footprint: 2688 bytes [ 0.000000] allocated 25165824 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.001000] Fast TSC calibration using PIT [ 0.002000] Detected 3199.977 MHz processor. [ 0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6399.95 BogoMIPS (lpj=3199977) [ 0.000711] pid_max: default: 32768 minimum: 301 [ 0.001940] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.004020] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.005028] Mount-cache hash table entries: 256 [ 0.005748] Initializing cgroup subsys debug [ 0.006058] Initializing cgroup subsys cpuacct [ 0.006390] Initializing cgroup subsys memory [ 0.006730] Initializing cgroup subsys devices [ 0.007046] Initializing cgroup subsys freezer [ 0.007373] Initializing cgroup subsys blkio [ 0.007739] CPU: Physical Processor ID: 0 [ 0.008038] CPU: Processor Core ID: 0 [ 0.008338] mce: CPU supports 9 MCE banks [ 0.008643] CPU0: Thermal monitoring enabled (TM1) [ 0.008981] using mwait in idle threads. [ 0.010132] ACPI: Core revision 20110623 [ 0.022136] ftrace: allocating 36036 entries in 142 pages [ 0.030650] Getting VERSION: 60015 [ 0.030927] Getting VERSION: 60015 [ 0.031213] Getting ID: 0 [ 0.031459] Getting ID: 0 [ 0.031707] Switched APIC routing to physical flat. [ 0.032038] enabled ExtINT on CPU#0 [ 0.032482] ENABLING IO-APIC IRQs [ 0.032754] init IO_APIC IRQs [ 0.033013] apic 8 pin 0 not connected [ 0.033319] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0) [ 0.033883] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0) [ 0.034457] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0) [ 0.035022] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0) [ 0.035589] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0) [ 0.036154] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0) [ 0.036721] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0) [ 0.037289] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 0.037854] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0) [ 0.038422] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0) [ 0.038994] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0) [ 0.039567] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0) [ 0.040139] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 0.040713] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0) [ 0.041286] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0) [ 0.041855] apic 8 pin 16 not connected [ 0.042148] apic 8 pin 17 not connected [ 0.042446] apic 8 pin 18 not connected [ 0.042741] apic 8 pin 19 not connected [ 0.043035] apic 8 pin 20 not connected [ 0.043332] apic 8 pin 21 not connected [ 0.043627] apic 8 pin 22 not connected [ 0.043921] apic 8 pin 23 not connected [ 0.044352] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.054725] CPU0: Genuine Intel(R) CPU 000 @ 3.20GHz stepping 04 [ 0.055208] Using local APIC timer interrupts. [ 0.055209] calibrating APIC timer ... [ 0.157159] ... lapic delta = 833232 [ 0.157440] ... PM-Timer delta = 357899 [ 0.157732] ... PM-Timer result ok [ 0.158008] ..... delta 833232 [ 0.158269] ..... mult: 35792482 [ 0.158539] ..... calibration result: 133317 [ 0.158846] ..... CPU clock speed is 3199.0617 MHz. [ 0.159176] ..... host bus clock speed is 133.0317 MHz. [ 0.159531] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver. [ 0.160291] ... version: 3 [ 0.160592] ... bit width: 48 [ 0.160894] ... generic registers: 4 [ 0.161192] ... value mask: 0000ffffffffffff [ 0.161540] ... max period: 000000007fffffff [ 0.161885] ... fixed-purpose events: 3 [ 0.162182] ... event mask: 000000070000000f [ 0.162919] lockdep: fixing up alternatives. [ 0.163292] Booting Node 0, Processors #1 [ 0.163511] smpboot cpu 1: start_ip = 97000 [ 0.175083] masked ExtINT on CPU#1 [ 0.254831] lockdep: fixing up alternatives. [ 0.255166] #2 [ 0.255259] smpboot cpu 2: start_ip = 97000 [ 0.266733] masked ExtINT on CPU#2 [ 0.346757] lockdep: fixing up alternatives. [ 0.347092] #3 [ 0.347183] smpboot cpu 3: start_ip = 97000 [ 0.358655] masked ExtINT on CPU#3 [ 0.438791] lockdep: fixing up alternatives. [ 0.439128] #4 [ 0.439221] smpboot cpu 4: start_ip = 97000 [ 0.450695] masked ExtINT on CPU#4 [ 0.530774] lockdep: fixing up alternatives. [ 0.531111] #5 [ 0.531204] smpboot cpu 5: start_ip = 97000 [ 0.542676] masked ExtINT on CPU#5 [ 0.622709] lockdep: fixing up alternatives. [ 0.623048] #6 [ 0.623141] smpboot cpu 6: start_ip = 97000 [ 0.634713] masked ExtINT on CPU#6 [ 0.714648] lockdep: fixing up alternatives. [ 0.717953] #7 [ 0.718045] smpboot cpu 7: start_ip = 97000 [ 0.729516] masked ExtINT on CPU#7 [ 0.809450] Brought up 8 CPUs [ 0.809713] Total of 8 processors activated (51187.64 BogoMIPS). [ 0.813444] CPU0 attaching sched-domain: [ 0.813743] domain 0: span 0,4 level SIBLING [ 0.814087] groups: 0 (cpu_power = 589) 4 (cpu_power = 589) [ 0.814621] domain 1: span 0-7 level MC [ 0.814952] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.815910] CPU1 attaching sched-domain: [ 0.816204] domain 0: span 1,5 level SIBLING [ 0.816551] groups: 1 (cpu_power = 589) 5 (cpu_power = 589) [ 0.817082] domain 1: span 0-7 level MC [ 0.817415] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.818370] CPU2 attaching sched-domain: [ 0.818665] domain 0: span 2,6 level SIBLING [ 0.819010] groups: 2 (cpu_power = 589) 6 (cpu_power = 589) [ 0.819544] domain 1: span 0-7 level MC [ 0.819875] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.820830] CPU3 attaching sched-domain: [ 0.821125] domain 0: span 3,7 level SIBLING [ 0.821471] groups: 3 (cpu_power = 589) 7 (cpu_power = 589) [ 0.822000] domain 1: span 0-7 level MC [ 0.822331] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.823287] CPU4 attaching sched-domain: [ 0.823585] domain 0: span 0,4 level SIBLING [ 0.823929] groups: 4 (cpu_power = 589) 0 (cpu_power = 589) [ 0.824462] domain 1: span 0-7 level MC [ 0.824794] groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) [ 0.825749] CPU5 attaching sched-domain: [ 0.826044] domain 0: span 1,5 level SIBLING [ 0.826390] groups: 5 (cpu_power = 589) 1 (cpu_power = 589) [ 0.826921] domain 1: span 0-7 level MC [ 0.827252] groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) [ 0.828208] CPU6 attaching sched-domain: [ 0.828505] domain 0: span 2,6 level SIBLING [ 0.828850] groups: 6 (cpu_power = 589) 2 (cpu_power = 589) [ 0.829381] domain 1: span 0-7 level MC [ 0.829713] groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) [ 0.830668] CPU7 attaching sched-domain: [ 0.830963] domain 0: span 3,7 level SIBLING [ 0.831307] groups: 7 (cpu_power = 589) 3 (cpu_power = 589) [ 0.831839] domain 1: span 0-7 level MC [ 0.832170] groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) [ 0.833624] kworker/u:0 used greatest stack depth: 5288 bytes left [ 0.835889] PM: Registering ACPI NVS region at bcda4000 (2330624 bytes) [ 0.836381] PM: Registering ACPI NVS region at bf714000 (700416 bytes) [ 0.837503] xor: automatically using best checksumming function: generic_sse [ 0.842342] generic_sse: 11928.000 MB/sec [ 0.842652] xor: using function: generic_sse (11928.000 MB/sec) [ 0.843102] RTC time: 17:22:24, date: 08/17/11 [ 0.843539] NET: Registered protocol family 16 [ 0.844545] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.845098] ACPI: bus type pci registered [ 0.845601] dca service started, version 1.12.1 [ 0.845999] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.846614] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 0.859855] PCI: Using configuration type 1 for base access [ 0.882707] bio: create slab at 0 [ 0.899334] raid6: int64x1 3171 MB/s [ 0.916683] raid6: int64x2 3390 MB/s [ 0.933317] raid6: int64x4 2738 MB/s [ 0.950327] raid6: int64x8 2101 MB/s [ 0.967311] raid6: sse2x1 7917 MB/s [ 0.984304] raid6: sse2x2 9273 MB/s [ 1.001298] raid6: sse2x4 10550 MB/s [ 1.001587] raid6: using algorithm sse2x4 (10550 MB/s) [ 1.002012] ACPI: Added _OSI(Module Device) [ 1.002327] ACPI: Added _OSI(Processor Device) [ 1.002643] ACPI: Added _OSI(3.0 _SCP Extensions) [ 1.002968] ACPI: Added _OSI(Processor Aggregator Device) [ 1.007302] ACPI: EC: Look up EC in DSDT [ 1.029507] ACPI: Interpreter enabled [ 1.029794] ACPI: (supports S0 S1 S3 S4 S5) [ 1.030307] ACPI: Using IOAPIC for interrupt routing [ 1.043210] ACPI: No dock devices found. [ 1.043512] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 1.044749] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d]) [ 1.046436] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] [ 1.046832] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] [ 1.047227] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] [ 1.047768] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff] [ 1.048309] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff] [ 1.048846] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff] [ 1.049410] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600 [ 1.049848] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604 [ 1.050273] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 1.050656] pci 0000:00:01.0: PME# disabled [ 1.050988] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604 [ 1.051418] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold [ 1.051796] pci 0000:00:03.0: PME# disabled [ 1.052127] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604 [ 1.052557] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold [ 1.052935] pci 0000:00:07.0: PME# disabled [ 1.053270] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800 [ 1.053718] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800 [ 1.054166] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800 [ 1.054614] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800 [ 1.055059] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800 [ 1.055506] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800 [ 1.055956] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200 [ 1.056349] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff] [ 1.056735] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff] [ 1.057121] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f] [ 1.057533] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.057911] pci 0000:00:19.0: PME# disabled [ 1.058235] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03 [ 1.058661] pci 0000:00:1a.0: reg 20: [io 0x20e0-0x20ff] [ 1.059068] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03 [ 1.059494] pci 0000:00:1a.1: reg 20: [io 0x20c0-0x20df] [ 1.059900] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03 [ 1.060327] pci 0000:00:1a.2: reg 20: [io 0x20a0-0x20bf] [ 1.060743] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03 [ 1.061133] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff] [ 1.061597] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 1.061975] pci 0000:00:1a.7: PME# disabled [ 1.062307] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403 [ 1.062694] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit] [ 1.063157] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 1.063539] pci 0000:00:1b.0: PME# disabled [ 1.063867] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604 [ 1.064311] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.064690] pci 0000:00:1c.0: PME# disabled [ 1.065017] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604 [ 1.065459] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 1.065837] pci 0000:00:1c.1: PME# disabled [ 1.066168] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604 [ 1.066610] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.066988] pci 0000:00:1c.4: PME# disabled [ 1.067322] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03 [ 1.067744] pci 0000:00:1d.0: reg 20: [io 0x2080-0x209f] [ 1.068149] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03 [ 1.068574] pci 0000:00:1d.1: reg 20: [io 0x2060-0x207f] [ 1.068978] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03 [ 1.069401] pci 0000:00:1d.2: reg 20: [io 0x2040-0x205f] [ 1.069816] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03 [ 1.070207] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff] [ 1.070670] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 1.071048] pci 0000:00:1d.7: PME# disabled [ 1.071374] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604 [ 1.071817] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601 [ 1.072288] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 1.072672] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f) [ 1.073222] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f) [ 1.073821] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106 [ 1.074211] pci 0000:00:1f.2: reg 10: [io 0x2128-0x212f] [ 1.074572] pci 0000:00:1f.2: reg 14: [io 0x2134-0x2137] [ 1.074930] pci 0000:00:1f.2: reg 18: [io 0x2120-0x2127] [ 1.075290] pci 0000:00:1f.2: reg 1c: [io 0x2130-0x2133] [ 1.075648] pci 0000:00:1f.2: reg 20: [io 0x2020-0x203f] [ 1.076007] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff] [ 1.076426] pci 0000:00:1f.2: PME# supported from D3hot [ 1.076772] pci 0000:00:1f.2: PME# disabled [ 1.077098] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05 [ 1.077488] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit] [ 1.077909] pci 0000:00:1f.3: reg 20: [io 0x2000-0x201f] [ 1.078336] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.078742] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300 [ 1.079123] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff] [ 1.079510] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref] [ 1.079939] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref] [ 1.080356] pci 0000:02:00.0: supports D1 D2 [ 1.080690] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403 [ 1.084045] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff] [ 1.084491] pci 0000:02:00.1: supports D1 D2 [ 1.084816] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.085162] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.085570] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.086169] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.086574] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.086975] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.087404] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101 [ 1.087796] pci 0000:06:00.0: reg 10: [io 0x1018-0x101f] [ 1.088160] pci 0000:06:00.0: reg 14: [io 0x1024-0x1027] [ 1.088528] pci 0000:06:00.0: reg 18: [io 0x1010-0x1017] [ 1.088892] pci 0000:06:00.0: reg 1c: [io 0x1020-0x1023] [ 1.089256] pci 0000:06:00.0: reg 20: [io 0x1000-0x100f] [ 1.089624] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff] [ 1.090063] pci 0000:06:00.0: supports D1 [ 1.090363] pci 0000:06:00.0: PME# supported from D0 D1 D3hot [ 1.090731] pci 0000:06:00.0: PME# disabled [ 1.091055] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.091405] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.091783] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.092236] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00 [ 1.092628] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff] [ 1.093013] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff] [ 1.093465] pci 0000:07:03.0: supports D1 D2 [ 1.093773] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot [ 1.094156] pci 0000:07:03.0: PME# disabled [ 1.094516] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode) [ 1.094932] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.095340] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.095900] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.096462] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.097047] pci 0000:00:1e.0: bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode) [ 1.097634] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode) [ 1.098219] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode) [ 1.098843] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 1.100201] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] [ 1.100843] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT] [ 1.101320] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT] [ 1.101794] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT] [ 1.102266] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] [ 1.102742] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] [ 1.103225] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] [ 1.103797] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19) [ 1.127906] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.128994] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.130077] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.131164] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.132251] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) [ 1.133338] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.134424] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) [ 1.135511] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) [ 1.136782] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none [ 1.137361] vgaarb: loaded [ 1.137612] vgaarb: bridge control possible 0000:02:00.0 [ 1.138266] SCSI subsystem initialized [ 1.138725] libata version 3.00 loaded. [ 1.139277] usbcore: registered new interface driver usbfs [ 1.139691] usbcore: registered new interface driver hub [ 1.140107] usbcore: registered new device driver usb [ 1.140882] wmi: Mapper loaded [ 1.141208] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 1.141598] PCI: Using ACPI for IRQ routing [ 1.143488] PCI: Discovered peer bus 3f [ 1.143860] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600 [ 1.144267] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600 [ 1.144672] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600 [ 1.145068] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600 [ 1.145476] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600 [ 1.145872] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600 [ 1.146275] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600 [ 1.146675] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600 [ 1.147074] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600 [ 1.147476] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600 [ 1.147874] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600 [ 1.148281] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600 [ 1.148680] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600 [ 1.149077] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600 [ 1.149479] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600 [ 1.149879] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600 [ 1.150281] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600 [ 1.150678] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600 [ 1.151076] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600 [ 1.152863] PCI: pci_cache_line_size set to 64 bytes [ 1.153449] reserve RAM buffer: 000000000009cc00 - 000000000009ffff [ 1.153712] reserve RAM buffer: 00000000bcda4000 - 00000000bfffffff [ 1.154132] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff [ 1.154556] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff [ 1.154977] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff [ 1.155399] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff [ 1.186866] pnp: PnP ACPI init [ 1.187311] ACPI: bus type pnp registered [ 1.188267] pnp 00:00: [bus 00-3d] [ 1.188544] pnp 00:00: [io 0x0cf8-0x0cff] [ 1.188846] pnp 00:00: [io 0x0000-0x0cf7 window] [ 1.189170] pnp 00:00: [io 0x0d00-0xffff window] [ 1.189502] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 1.189853] pnp 00:00: [mem 0x000c4000-0x000cbfff window] [ 1.190204] pnp 00:00: [mem 0xfed40000-0xfedfffff window] [ 1.190559] pnp 00:00: [mem 0xd0000000-0xf7ffffff window] [ 1.190910] pnp 00:00: [mem 0x00000000 window] [ 1.191370] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 1.192052] pnp 00:01: [io 0x0000-0x000f] [ 1.192361] pnp 00:01: [io 0x0081-0x0083] [ 1.192665] pnp 00:01: [io 0x0087] [ 1.192944] pnp 00:01: [io 0x0089-0x008b] [ 1.193249] pnp 00:01: [io 0x008f] [ 1.193529] pnp 00:01: [io 0x00c0-0x00df] [ 1.193832] pnp 00:01: [dma 4] [ 1.194187] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 1.194601] pnp 00:02: [io 0x0070-0x0071] [ 1.194904] pnp 00:02: [io 0x0074-0x0077] [ 1.195210] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0) [ 1.195778] pnp 00:02: [irq 8] [ 1.196135] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.196552] pnp 00:03: [io 0x00f0] [ 1.196833] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0) [ 1.197408] pnp 00:03: [irq 13] [ 1.197766] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 1.198180] pnp 00:04: [io 0x0061] [ 1.198560] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 1.198974] pnp 00:05: [io 0x0500-0x053f] [ 1.199280] pnp 00:05: [io 0x0400-0x047f] [ 1.199582] pnp 00:05: [io 0x0092] [ 1.199861] pnp 00:05: [io 0x0680-0x06ff] [ 1.200162] pnp 00:05: [io 0x0010-0x001f] [ 1.200467] pnp 00:05: [io 0x0072-0x0073] [ 1.200769] pnp 00:05: [io 0x0080] [ 1.201048] pnp 00:05: [io 0x0084-0x0086] [ 1.201351] pnp 00:05: [io 0x0088] [ 1.201631] pnp 00:05: [io 0x008c-0x008e] [ 1.201932] pnp 00:05: [io 0x0090-0x009f] [ 1.202418] system 00:05: [io 0x0500-0x053f] has been reserved [ 1.202789] system 00:05: [io 0x0400-0x047f] has been reserved [ 1.203158] system 00:05: [io 0x0680-0x06ff] has been reserved [ 1.203537] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.204020] pnp 00:06: [io 0x0060] [ 1.204307] pnp 00:06: [io 0x0064] [ 1.204753] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.205721] pnp 00:07: [mem 0xfec00000-0xfec000ff] [ 1.206158] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active) [ 1.206693] pnp: PnP ACPI: found 8 devices [ 1.206997] ACPI: ACPI bus type pnp unregistered [ 1.217026] Switching to clocksource acpi_pm [ 1.217379] Switched to NOHz mode on CPU #4 [ 1.217793] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref] [ 1.218311] Switched to NOHz mode on CPU #6 [ 1.218313] Switched to NOHz mode on CPU #2 [ 1.218331] Switched to NOHz mode on CPU #7 [ 1.218336] Switched to NOHz mode on CPU #5 [ 1.218347] Switched to NOHz mode on CPU #1 [ 1.218366] Switched to NOHz mode on CPU #3 [ 1.220240] Switched to NOHz mode on CPU #0 [ 1.220591] PCI: max bus depth: 1 pci_try_num: 2 [ 1.220970] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 1.221324] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref] [ 1.221865] pci 0000:00:03.0: PCI bridge to [bus 02-02] [ 1.222211] pci 0000:00:03.0: bridge window [mem 0xe0200000-0xe02fffff] [ 1.222623] pci 0000:00:03.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.226156] pci 0000:00:07.0: PCI bridge to [bus 03-03] [ 1.226516] pci 0000:00:1c.0: PCI bridge to [bus 04-04] [ 1.226869] pci 0000:00:1c.1: PCI bridge to [bus 05-05] [ 1.227222] pci 0000:00:1c.4: PCI bridge to [bus 06-06] [ 1.227576] pci 0000:00:1c.4: bridge window [io 0x1000-0x1fff] [ 1.227955] pci 0000:00:1c.4: bridge window [mem 0xe0100000-0xe01fffff] [ 1.228363] pci 0000:00:1e.0: PCI bridge to [bus 07-07] [ 1.228717] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xe00fffff] [ 1.229139] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0) [ 1.229720] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.230121] pci 0000:00:01.0: setting latency timer to 64 [ 1.230476] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.230882] pci 0000:00:03.0: setting latency timer to 64 [ 1.231238] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.231647] pci 0000:00:07.0: setting latency timer to 64 [ 1.232008] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0) [ 1.232584] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.232985] pci 0000:00:1c.0: setting latency timer to 64 [ 1.233341] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 1.233751] pci 0000:00:1c.1: setting latency timer to 64 [ 1.234107] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.234517] pci 0000:00:1c.4: setting latency timer to 64 [ 1.234873] pci 0000:00:1e.0: setting latency timer to 64 [ 1.235226] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.235591] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.235948] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.236331] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.236722] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.237105] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.237487] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff] [ 1.237876] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 1.238409] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 1.238772] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff] [ 1.239154] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff] [ 1.239545] pci_bus 0000:07: resource 4 [io 0x0000-0x0cf7] [ 1.239901] pci_bus 0000:07: resource 5 [io 0x0d00-0xffff] [ 1.240257] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff] [ 1.240648] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff] [ 1.241030] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff] [ 1.241412] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff] [ 1.241800] pci_bus 0000:3f: resource 0 [io 0x0000-0xffff] [ 1.242157] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff] [ 1.242703] NET: Registered protocol family 2 [ 1.243372] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 1.245920] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 1.249685] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes) [ 1.253073] TCP: Hash tables configured (established 524288 bind 65536) [ 1.253485] TCP reno registered [ 1.253829] UDP hash table entries: 2048 (order: 6, 393216 bytes) [ 1.254459] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes) [ 1.255261] NET: Registered protocol family 1 [ 1.255856] RPC: Registered named UNIX socket transport module. [ 1.256228] RPC: Registered udp transport module. [ 1.256567] RPC: Registered tcp transport module. [ 1.256893] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.257324] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.257724] pci 0000:00:1a.0: Performing full reset [ 1.258073] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.258466] pci 0000:00:1a.1: Performing full reset [ 1.258822] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.259213] pci 0000:00:1a.2: Performing full reset [ 1.259720] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10 [ 1.260111] pci 0000:00:1d.0: Performing full reset [ 1.260458] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.260869] pci 0000:00:1d.1: Performing full reset [ 1.261219] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010 [ 1.261619] pci 0000:00:1d.2: Performing full reset [ 1.262111] pci 0000:02:00.0: Boot video device [ 1.262487] PCI: CLS 64 bytes, default 64 [ 1.266705] Machine check injector initialized [ 1.268576] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6 [ 1.268949] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6 [ 1.269323] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6 [ 1.269705] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6 [ 1.270076] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6 [ 1.270452] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6 [ 1.270822] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6 [ 1.271193] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6 [ 1.271646] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 1.272732] audit: initializing netlink socket (disabled) [ 1.273111] type=2000 audit(1313601744.025:1): initialized [ 1.303685] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.305635] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 1.306350] fuse init (API version 7.16) [ 1.306861] JFS: nTxBlock = 8192, nTxLock = 65536 [ 1.310354] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 1.311716] NILFS version 2 loaded [ 1.312295] Btrfs loaded [ 1.312561] msgmni has been set to 5896 [ 1.313707] async_tx: api initialized (async) [ 1.314119] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.314728] io scheduler noop registered [ 1.315024] io scheduler deadline registered [ 1.315382] io scheduler cfq registered (default) [ 1.316152] pcieport 0000:00:1c.0: setting latency timer to 64 [ 1.316590] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 1.317063] pcieport 0000:00:1c.1: setting latency timer to 64 [ 1.317476] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 1.317960] pcieport 0000:00:1c.4: setting latency timer to 64 [ 1.318374] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 1.319083] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.319909] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0 [ 1.320492] ACPI: Sleep Button [SLPB] [ 1.320922] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 1.321468] ACPI: Power Button [PWRF] [ 1.322486] ACPI: acpi_idle registered with cpuidle [ 1.323247] Monitor-Mwait will be used to enter C-1 state [ 1.323663] Monitor-Mwait will be used to enter C-3 state [ 1.331336] ioatdma: Intel(R) QuickData Technology Driver 4.00 [ 1.375562] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.391618] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A [ 1.440821] Initializing Nozomi driver 2.1d [ 1.441633] Non-volatile memory driver v1.3 [ 1.442378] Linux agpgart interface v0.103 [ 1.442779] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds). [ 1.443379] Hangcheck: Using getrawmonotonic(). [ 1.443776] [drm] Initialized drm 1.1.0 20060810 [ 1.444098] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 2.264611] Refined TSC clocksource calibration: 3200.113 MHz. [ 2.264980] Switching to clocksource tsc [ 4.462741] floppy0: no floppy controllers found [ 4.594588] brd: module loaded [ 4.596402] loop: module loaded [ 4.597157] Loading iSCSI transport class v2.0-870. [ 4.598091] Loading Adaptec I2O RAID: Version 2.4 Build 5go [ 4.598447] Detecting Adaptec I2O RAID controllers... [ 4.598973] Adaptec aacraid driver 1.1-7[28000]-ms [ 4.599865] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded [ 4.600488] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.03-k. [ 4.601235] iscsi: registered transport (qla4xxx) [ 4.601638] QLogic iSCSI HBA Driver [ 4.601997] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) [ 4.602606] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) [ 4.603098] megasas: 00.00.05.40-rc1 Tue. Jul. 26 17:00:00 PDT 2011 [ 4.603562] mpt2sas version 09.100.00.00 loaded [ 4.604282] ahci 0000:00:1f.2: version 3.0 [ 4.604615] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0) [ 4.605190] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 4.605647] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X [ 4.606062] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 4.606639] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems [ 4.607204] ahci 0000:00:1f.2: setting latency timer to 64 [ 4.617967] scsi0 : ahci [ 4.618435] scsi1 : ahci [ 4.618845] scsi2 : ahci [ 4.619242] scsi3 : ahci [ 4.619658] scsi4 : ahci [ 4.620059] scsi5 : ahci [ 4.620733] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43 [ 4.621276] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43 [ 4.621821] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43 [ 4.622363] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43 [ 4.622908] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43 [ 4.623450] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43 [ 4.624024] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.624440] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this. [ 4.628077] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ [ 4.628484] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP [ 4.628894] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3 [ 4.629266] ahci: SSS flag set, parallel bus scan disabled [ 4.629661] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode [ 4.630224] ahci 0000:06:00.0: flags: 64bit stag led slum part [ 4.630597] ahci 0000:06:00.0: setting latency timer to 64 [ 4.631825] scsi6 : ahci [ 4.632230] scsi7 : ahci [ 4.632633] scsi8 : ahci [ 4.633016] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16 [ 4.633558] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16 [ 4.634101] ata9: DUMMY [ 4.636357] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 4.636772] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 4.637215] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k [ 4.637584] e1000e: Copyright(c) 1999 - 2011 Intel Corporation. [ 4.637988] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0) [ 4.638557] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 4.638973] e1000e 0000:00:19.0: setting latency timer to 64 [ 4.639441] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 4.830144] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54 [ 4.830713] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.831151] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF [ 4.831628] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k [ 4.832024] Copyright (c) 2007-2011 Intel Corporation. [ 4.832444] Intel(R) Virtual Function Network Driver - version 2.0.0-k [ 4.832842] Copyright (c) 2009 - 2010 Intel Corporation. [ 4.833267] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k [ 4.833820] ixgbe: Copyright (c) 1999-2011 Intel Corporation. [ 4.834259] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI [ 4.834675] ixgb: Copyright (c) 1999-2008 Intel Corporation. [ 4.835403] jme: JMicron JMC2XX ethernet driver version 1.0.8 [ 4.835844] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI [ 4.836219] e100: Copyright(c) 1999-2006 Intel Corporation [ 4.836875] ns83820.c: National Semiconductor DP83820 10/100/1000 driver. [ 4.837497] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011) [ 4.838153] sky2: driver version 1.29 [ 4.839446] tun: Universal TUN/TAP device driver, 1.6 [ 4.839788] tun: (C) 1999-2004 Max Krasnyansky [ 4.840441] usbcore: registered new interface driver catc [ 4.840796] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver [ 4.841217] usbcore: registered new interface driver kaweth [ 4.841573] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver [ 4.842169] usbcore: registered new interface driver pegasus [ 4.842529] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver [ 4.842988] usbcore: registered new interface driver rtl8150 [ 4.843396] usbcore: registered new interface driver asix [ 4.843799] usbcore: registered new interface driver cdc_ether [ 4.844216] usbcore: registered new interface driver cdc_eem [ 4.844624] usbcore: registered new interface driver dm9601 [ 4.845050] usbcore: registered new interface driver smsc75xx [ 4.845466] usbcore: registered new interface driver smsc95xx [ 4.845886] usbcore: registered new interface driver gl620a [ 4.846292] usbcore: registered new interface driver net1080 [ 4.846705] usbcore: registered new interface driver plusb [ 4.847107] usbcore: registered new interface driver rndis_host [ 4.847525] usbcore: registered new interface driver cdc_subset [ 4.847950] usbcore: registered new interface driver zaurus [ 4.848357] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 4.848961] usbcore: registered new interface driver int51x1 [ 4.849322] cdc_ncm: 04-Aug-2011 [ 4.849647] usbcore: registered new interface driver cdc_ncm [ 4.850010] netconsole: local port 6665 [ 4.850303] netconsole: local IP 10.0.0.0 [ 4.850602] netconsole: interface 'eth0' [ 4.850903] netconsole: remote port 6666 [ 4.851199] netconsole: remote IP 192.168.1.1 [ 4.851509] netconsole: remote ethernet address 00:30:48:fe:19:95 [ 4.851890] netconsole: device eth0 not up yet, forcing it [ 4.928677] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.929078] ata5: SATA link down (SStatus 0 SControl 300) [ 4.929449] ata6: SATA link down (SStatus 0 SControl 300) [ 4.929831] ata3: SATA link down (SStatus 0 SControl 300) [ 4.930201] ata4: SATA link down (SStatus 0 SControl 300) [ 4.938678] ata7: SATA link down (SStatus 0 SControl 300) [ 4.945111] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 4.976713] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133 [ 4.977074] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 4.995723] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X [ 5.035018] ata1.00: configured for UDMA/133 [ 5.035514] scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 [ 5.036411] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 5.037049] sd 0:0:0:0: [sda] Write Protect is off [ 5.037378] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.037747] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.127055] sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 > [ 5.128304] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.286779] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 5.363579] ata2.00: ATAPI: PLEXTOR DVDR PX-712A, 1.07, max UDMA/33 [ 5.363977] ata2.00: applying bridge limits [ 5.394830] ata2.00: configured for UDMA/33 [ 5.396144] scsi 1:0:0:0: CD-ROM PLEXTOR DVDR PX-712A 1.07 PQ: 0 ANSI: 5 [ 5.701713] ata8: SATA link down (SStatus 0 SControl 300) [ 7.769673] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 7.773141] console [netcon0] enabled [ 7.773432] netconsole: network logging started [ 7.773821] Fusion MPT base driver 3.04.19 [ 7.774127] Copyright (c) 1999-2008 LSI Corporation [ 7.774469] Fusion MPT SPI Host driver 3.04.19 [ 7.774874] Fusion MPT FC Host driver 3.04.19 [ 7.775273] Fusion MPT SAS Host driver 3.04.19 [ 7.775675] Fusion MPT misc device (ioctl) driver 3.04.19 [ 7.776105] mptctl: Registered with Fusion MPT base driver [ 7.776462] mptctl: /dev/mptctl @ (major,minor=10,220) [ 7.776908] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.777303] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 7.777724] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0) [ 7.778303] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 7.778736] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 7.779111] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 7.779525] /c/wfg/linux/drivers/usb/core/inode.c: creating file 'devices' [ 7.779952] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.780358] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 7.780917] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 7.781519] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 7.782175] ehci_hcd 0000:00:1a.7: debug port 1 [ 7.782497] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.786979] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 7.787383] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 7.787773] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000 [ 7.788137] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.792622] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 7.798758] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 7.799209] usb usb1: default language 0x0409 [ 7.799532] usb usb1: udev 1, busnum 1, minor = 0 [ 7.799863] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.800267] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.800807] usb usb1: Product: EHCI Host Controller [ 7.801140] usb usb1: Manufacturer: Linux 3.1.0-rc1+ ehci_hcd [ 7.801505] usb usb1: SerialNumber: 0000:00:1a.7 [ 7.801952] usb usb1: usb_probe_device [ 7.802246] usb usb1: configuration #1 chosen from 1 choice [ 7.802631] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 7.803083] hub 1-0:1.0: usb_probe_interface [ 7.803395] hub 1-0:1.0: usb_probe_interface - got id [ 7.803736] hub 1-0:1.0: USB hub found [ 7.804038] hub 1-0:1.0: 6 ports detected [ 7.804339] hub 1-0:1.0: standalone hub [ 7.804634] hub 1-0:1.0: no power switching (usb 1.0) [ 7.804976] hub 1-0:1.0: individual port over-current protection [ 7.805353] hub 1-0:1.0: power on to power good time: 20ms [ 7.805727] hub 1-0:1.0: local power source is good [ 7.806065] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 7.806523] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.807044] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0) [ 7.807618] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 7.808051] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 7.808422] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 7.808777] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002' [ 7.809176] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 7.809727] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 7.810332] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch [ 7.813951] ehci_hcd 0000:00:1d.7: debug port 1 [ 7.814273] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.818749] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 7.819153] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 7.819541] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000 [ 7.819911] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 7.824392] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN [ 7.830759] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 7.831167] usb usb2: default language 0x0409 [ 7.831490] usb usb2: udev 1, busnum 2, minor = 128 [ 7.831827] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 7.832231] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.832770] usb usb2: Product: EHCI Host Controller [ 7.833102] usb usb2: Manufacturer: Linux 3.1.0-rc1+ ehci_hcd [ 7.833468] usb usb2: SerialNumber: 0000:00:1d.7 [ 7.833909] usb usb2: usb_probe_device [ 7.834201] usb usb2: configuration #1 chosen from 1 choice [ 7.834568] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 7.835001] hub 2-0:1.0: usb_probe_interface [ 7.835312] hub 2-0:1.0: usb_probe_interface - got id [ 7.835651] hub 2-0:1.0: USB hub found [ 7.835951] hub 2-0:1.0: 6 ports detected [ 7.836251] hub 2-0:1.0: standalone hub [ 7.836546] hub 2-0:1.0: no power switching (usb 1.0) [ 7.836888] hub 2-0:1.0: individual port over-current protection [ 7.837263] hub 2-0:1.0: power on to power good time: 20ms [ 7.837624] hub 2-0:1.0: local power source is good [ 7.837960] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 7.838414] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.838969] uhci_hcd: USB Universal Host Controller Interface driver [ 7.839407] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 7.839834] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 7.840204] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 7.840557] /c/wfg/linux/drivers/usb/core/inode.c: creating file '003' [ 7.840959] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 7.841511] uhci_hcd 0000:00:1a.0: detected 2 ports [ 7.841850] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.842251] uhci_hcd 0000:00:1a.0: Performing full reset [ 7.842611] uhci_hcd 0000:00:1a.0: supports USB remote wakeup [ 7.842982] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0 [ 7.843406] usb usb3: default language 0x0409 [ 7.843728] usb usb3: udev 1, busnum 3, minor = 256 [ 7.844066] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.844470] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.845009] usb usb3: Product: UHCI Host Controller [ 7.845341] usb usb3: Manufacturer: Linux 3.1.0-rc1+ uhci_hcd [ 7.845706] usb usb3: SerialNumber: 0000:00:1a.0 [ 7.846161] usb usb3: usb_probe_device [ 7.846455] usb usb3: configuration #1 chosen from 1 choice [ 7.846826] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 7.847263] hub 3-0:1.0: usb_probe_interface [ 7.847576] hub 3-0:1.0: usb_probe_interface - got id [ 7.847920] hub 3-0:1.0: USB hub found [ 7.848217] hub 3-0:1.0: 2 ports detected [ 7.848519] hub 3-0:1.0: standalone hub [ 7.848816] hub 3-0:1.0: no power switching (usb 1.0) [ 7.849157] hub 3-0:1.0: individual port over-current protection [ 7.849533] hub 3-0:1.0: power on to power good time: 2ms [ 7.849894] hub 3-0:1.0: local power source is good [ 7.850230] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 7.850661] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.851116] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0 [ 7.851554] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0) [ 7.852129] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 7.852550] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 7.852923] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 7.853277] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004' [ 7.853676] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 7.854233] uhci_hcd 0000:00:1a.1: detected 2 ports [ 7.854569] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.854973] uhci_hcd 0000:00:1a.1: Performing full reset [ 7.855334] uhci_hcd 0000:00:1a.1: supports USB remote wakeup [ 7.855719] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0 [ 7.856128] usb usb4: default language 0x0409 [ 7.856451] usb usb4: udev 1, busnum 4, minor = 384 [ 7.856788] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.857192] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.857728] usb usb4: Product: UHCI Host Controller [ 7.858063] usb usb4: Manufacturer: Linux 3.1.0-rc1+ uhci_hcd [ 7.858428] usb usb4: SerialNumber: 0000:00:1a.1 [ 7.858870] usb usb4: usb_probe_device [ 7.859163] usb usb4: configuration #1 chosen from 1 choice [ 7.859528] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 7.859967] hub 4-0:1.0: usb_probe_interface [ 7.860278] hub 4-0:1.0: usb_probe_interface - got id [ 7.860617] hub 4-0:1.0: USB hub found [ 7.860916] hub 4-0:1.0: 2 ports detected [ 7.861217] hub 4-0:1.0: standalone hub [ 7.861511] hub 4-0:1.0: no power switching (usb 1.0) [ 7.861853] hub 4-0:1.0: individual port over-current protection [ 7.862227] hub 4-0:1.0: power on to power good time: 2ms [ 7.862584] hub 4-0:1.0: local power source is good [ 7.862920] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 7.863350] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.863798] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1 [ 7.864231] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 7.864653] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 7.865028] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 7.865383] /c/wfg/linux/drivers/usb/core/inode.c: creating file '005' [ 7.865790] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 7.866340] uhci_hcd 0000:00:1a.2: detected 2 ports [ 7.866676] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.867079] uhci_hcd 0000:00:1a.2: Performing full reset [ 7.867438] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 7.867829] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0 [ 7.868235] usb usb5: default language 0x0409 [ 7.868558] usb usb5: udev 1, busnum 5, minor = 512 [ 7.868896] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.869301] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.869841] usb usb5: Product: UHCI Host Controller [ 7.870175] usb usb5: Manufacturer: Linux 3.1.0-rc1+ uhci_hcd [ 7.870541] usb usb5: SerialNumber: 0000:00:1a.2 [ 7.870984] usb usb5: usb_probe_device [ 7.871278] usb usb5: configuration #1 chosen from 1 choice [ 7.871644] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 7.872079] hub 5-0:1.0: usb_probe_interface [ 7.872391] hub 5-0:1.0: usb_probe_interface - got id [ 7.872731] hub 5-0:1.0: USB hub found [ 7.873030] hub 5-0:1.0: 2 ports detected [ 7.873331] hub 5-0:1.0: standalone hub [ 7.873625] hub 5-0:1.0: no power switching (usb 1.0) [ 7.873967] hub 5-0:1.0: individual port over-current protection [ 7.874342] hub 5-0:1.0: power on to power good time: 2ms [ 7.874699] hub 5-0:1.0: local power source is good [ 7.875036] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 7.875466] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.875914] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2 [ 7.876347] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 7.876772] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 7.877142] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 7.877496] /c/wfg/linux/drivers/usb/core/inode.c: creating file '006' [ 7.877899] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 7.878450] uhci_hcd 0000:00:1d.0: detected 2 ports [ 7.878789] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.879189] uhci_hcd 0000:00:1d.0: Performing full reset [ 7.879550] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 7.879923] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080 [ 7.880335] usb usb6: default language 0x0409 [ 7.880657] usb usb6: udev 1, busnum 6, minor = 640 [ 7.880995] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.881399] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.881938] usb usb6: Product: UHCI Host Controller [ 7.882271] usb usb6: Manufacturer: Linux 3.1.0-rc1+ uhci_hcd [ 7.882636] usb usb6: SerialNumber: 0000:00:1d.0 [ 7.883077] usb usb6: usb_probe_device [ 7.883371] usb usb6: configuration #1 chosen from 1 choice [ 7.883736] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 7.884174] hub 6-0:1.0: usb_probe_interface [ 7.884486] hub 6-0:1.0: usb_probe_interface - got id [ 7.884831] hub 6-0:1.0: USB hub found [ 7.885128] hub 6-0:1.0: 2 ports detected [ 7.885428] hub 6-0:1.0: standalone hub [ 7.885723] hub 6-0:1.0: no power switching (usb 1.0) [ 7.886067] hub 6-0:1.0: individual port over-current protection [ 7.886443] hub 6-0:1.0: power on to power good time: 2ms [ 7.886805] hub 6-0:1.0: local power source is good [ 7.887139] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 7.887573] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.888037] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0 [ 7.888460] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 7.888886] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 7.889257] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 7.889612] /c/wfg/linux/drivers/usb/core/inode.c: creating file '007' [ 7.890015] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 7.890567] uhci_hcd 0000:00:1d.1: detected 2 ports [ 7.890906] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.894282] uhci_hcd 0000:00:1d.1: Performing full reset [ 7.894642] uhci_hcd 0000:00:1d.1: supports USB remote wakeup [ 7.895013] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060 [ 7.895417] usb usb7: default language 0x0409 [ 7.895739] usb usb7: udev 1, busnum 7, minor = 768 [ 7.896076] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.896479] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.897019] usb usb7: Product: UHCI Host Controller [ 7.897351] usb usb7: Manufacturer: Linux 3.1.0-rc1+ uhci_hcd [ 7.897715] usb usb7: SerialNumber: 0000:00:1d.1 [ 7.898159] usb usb7: usb_probe_device [ 7.898451] usb usb7: configuration #1 chosen from 1 choice [ 7.898821] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 7.899252] hub 7-0:1.0: usb_probe_interface [ 7.899562] hub 7-0:1.0: usb_probe_interface - got id [ 7.899905] hub 7-0:1.0: USB hub found [ 7.900201] hub 7-0:1.0: 2 ports detected [ 7.900501] hub 7-0:1.0: standalone hub [ 7.900800] hub 7-0:1.0: no power switching (usb 1.0) [ 7.901139] hub 7-0:1.0: individual port over-current protection [ 7.901513] hub 7-0:1.0: power on to power good time: 2ms [ 7.901874] hub 7-0:1.0: local power source is good [ 7.902207] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 7.902638] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.903099] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1 [ 7.903522] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 7.903948] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 7.904319] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 7.904673] /c/wfg/linux/drivers/usb/core/inode.c: creating file '008' [ 7.905076] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 7.905627] uhci_hcd 0000:00:1d.2: detected 2 ports [ 7.905983] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 7.906384] uhci_hcd 0000:00:1d.2: Performing full reset [ 7.906749] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 7.907128] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 7.907724] hub 1-0:1.0: port 1: status 0501 change 0001 [ 7.908085] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT [ 7.908681] hub 1-0:1.0: port 2: status 0501 change 0001 [ 7.909047] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040 [ 7.909049] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0 ACK POWER sig=j CSC CONNECT [ 7.909055] hub 1-0:1.0: port 4: status 0501 change 0001 [ 7.910402] usb usb8: default language 0x0409 [ 7.910727] usb usb8: udev 1, busnum 8, minor = 896 [ 7.911065] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 7.911470] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 7.912011] usb usb8: Product: UHCI Host Controller [ 7.912346] usb usb8: Manufacturer: Linux 3.1.0-rc1+ uhci_hcd [ 7.912714] usb usb8: SerialNumber: 0000:00:1d.2 [ 7.913160] usb usb8: usb_probe_device [ 7.913457] usb usb8: configuration #1 chosen from 1 choice [ 7.913829] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 7.914266] hub 8-0:1.0: usb_probe_interface [ 7.914580] hub 8-0:1.0: usb_probe_interface - got id [ 7.914925] hub 8-0:1.0: USB hub found [ 7.915223] hub 8-0:1.0: 2 ports detected [ 7.915526] hub 8-0:1.0: standalone hub [ 7.915826] hub 8-0:1.0: no power switching (usb 1.0) [ 7.916169] hub 8-0:1.0: individual port over-current protection [ 7.916545] hub 8-0:1.0: power on to power good time: 2ms [ 7.916910] hub 8-0:1.0: local power source is good [ 7.917245] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 7.917679] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001' [ 7.918148] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2 [ 7.918626] Initializing USB Mass Storage driver... [ 7.919046] usbcore: registered new interface driver usb-storage [ 7.919424] USB Mass Storage support registered. [ 7.919847] usbcore: registered new interface driver libusual [ 7.920272] usbcore: registered new interface driver ums-alauda [ 7.920704] usbcore: registered new interface driver ums-cypress [ 7.921142] usbcore: registered new interface driver ums-datafab [ 7.921574] usbcore: registered new interface driver ums-freecom [ 7.922013] usbcore: registered new interface driver ums-isd200 [ 7.922442] usbcore: registered new interface driver ums-jumpshot [ 7.922879] usbcore: registered new interface driver ums-karma [ 7.923304] usbcore: registered new interface driver ums-onetouch [ 7.923739] usbcore: registered new interface driver ums-sddr09 [ 7.924172] usbcore: registered new interface driver ums-sddr55 [ 7.924600] usbcore: registered new interface driver ums-usbat [ 7.925094] usbcore: registered new interface driver usbserial [ 7.925519] USB Serial support registered for generic [ 7.925929] usbcore: registered new interface driver usbserial_generic [ 7.926327] usbserial: USB Serial Driver core [ 7.926688] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter [ 7.927330] usbcore: registered new interface driver belkin [ 7.927692] belkin_sa: v1.3:USB Belkin Serial converter driver [ 7.928112] USB Serial support registered for MCT U232 [ 7.928518] usbcore: registered new interface driver mct_u232 [ 7.928890] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver [ 7.929620] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 7.933219] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 7.933573] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 7.934212] mousedev: PS/2 mouse device common for all mice [ 7.935206] rtc_cmos 00:02: RTC can wake from S4 [ 7.935732] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 7.936145] rtc0: alarms up to one month, y3k, 114 bytes nvram [ 7.936567] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06 [ 7.937102] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460) [ 7.937625] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 7.937789] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 7.938360] iTCO_vendor_support: vendor-support=0 [ 7.938686] SoftDog: cannot register miscdev on minor=130 (err=-16) [ 7.939081] md: linear personality registered for level -1 [ 7.939437] md: raid0 personality registered for level 0 [ 7.939789] md: raid1 personality registered for level 1 [ 7.940137] md: raid10 personality registered for level 10 [ 7.940492] md: raid6 personality registered for level 6 [ 7.940847] md: raid5 personality registered for level 5 [ 7.941196] md: raid4 personality registered for level 4 [ 7.941545] md: multipath personality registered for level -4 [ 7.941913] md: faulty personality registered for level -5 [ 7.942343] device-mapper: uevent: version 1.0.3 [ 7.942794] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com [ 7.943514] device-mapper: multipath: version 1.3.0 loaded [ 7.943884] device-mapper: multipath round-robin: version 1.0.0 loaded [ 7.944278] device-mapper: multipath queue-length: version 0.1.0 loaded [ 7.944676] device-mapper: multipath service-time: version 0.2.0 loaded [ 7.945168] device-mapper: dm-log-userspace: version 1.1.0 loaded [ 7.946886] cpuidle: using governor ladder [ 7.949764] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00 [ 7.949855] cpuidle: using governor menu [ 7.950058] usbcore: registered new interface driver usbhid [ 7.950060] usbhid: USB HID core driver [ 7.950401] dell_wmi: No known WMI GUID found [ 7.950403] acer_wmi: Acer Laptop ACPI-WMI Extras [ 7.950408] acer_wmi: No or unsupported WMI interface, unable to load [ 7.950769] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0) [ 7.950774] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 7.950829] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 7.950860] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 7.950864] ALSA hda_intel.c:2598 chipset global capabilities = 0x4401 [ 7.950877] ALSA hda_intel.c:1091 Clearing TCSEL [ 7.954737] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00 [ 7.958884] ALSA hda_intel.c:945 codec_mask = 0x4 [ 7.959425] ALSA hda_intel.c:1392 codec #2 probed OK [ 7.962783] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00 [ 7.964892] ALSA hda_codec.c:3955 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO) [ 7.965505] hda_codec: ALC889: SKU not ready 0x411111f0 [ 7.966050] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2 [ 7.969403] ALSA hda_codec.c:2339 Cannot find slave Side Playback Volume, skipped [ 7.969962] ALSA hda_codec.c:2339 Cannot find slave Headphone Playback Volume, skipped [ 7.970525] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Volume, skipped [ 7.971078] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Volume, skipped [ 7.971644] ALSA hda_codec.c:2339 Cannot find slave Side Playback Switch, skipped [ 7.972199] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Switch, skipped [ 7.972749] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Switch, skipped [ 7.973924] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3 [ 7.974826] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.974942] ALSA device list: [ 7.974944] #0: HDA Intel at 0xf7f00000 irq 45 [ 7.974947] oprofile: using NMI interrupt. [ 7.976126] netem: version 1.3 [ 7.976393] Netfilter messages via NETLINK v0.30. [ 7.976756] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 7.977755] ctnetlink v0.93: registering with nfnetlink. [ 7.978146] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 7.978555] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 7.979197] xt_time: kernel timezone is -0000 [ 7.980852] ip_tables: (C) 2000-2006 Netfilter Core Team [ 7.981310] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully [ 7.984715] arp_tables: (C) 2002 David S. Miller [ 7.985104] TCP bic registered [ 7.985397] TCP cubic registered [ 7.985693] TCP westwood registered [ 7.985978] TCP highspeed registered [ 7.986262] TCP hybla registered [ 7.986532] TCP htcp registered [ 7.986810] TCP vegas registered [ 7.986832] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 7.987432] TCP veno registered [ 7.987700] TCP scalable registered [ 7.987985] TCP lp registered [ 7.988246] TCP yeah registered [ 7.988512] TCP illinois registered [ 7.988802] Initializing XFRM netlink socket [ 7.989128] NET: Registered protocol family 17 [ 7.989453] NET: Registered protocol family 15 [ 7.990126] Bridge firewalling registered [ 7.990439] Ebtables v2.0 registered [ 7.990829] [ 7.990830] printing PIC contents [ 7.991312] ... PIC IMR: ffff [ 7.991577] ... PIC IRR: 0c21 [ 7.991922] ... PIC ISR: 0000 [ 7.992189] ... PIC ELCR: 0c20 [ 7.992455] printing local APIC contents on CPU#0/0: [ 7.992792] ... APIC ID: 00000000 (0) [ 7.993094] ... APIC VERSION: 00060015 [ 7.993382] ... APIC TASKPRI: 00000000 (00) [ 7.993687] ... APIC PROCPRI: 00000000 [ 7.993976] ... APIC LDR: 01000000 [ 7.994251] ... APIC DFR: ffffffff [ 7.994527] ... APIC SPIV: 000001ff [ 7.994806] ... APIC ISR field: [ 7.995072] 0000000000000000000000000000000000000000000000000000000000000000 [ 7.995754] ... APIC TMR field: [ 7.996020] 0000000000000000000000000000000000020000000000000000000000000000 [ 7.996702] ... APIC IRR field: [ 7.996968] 0000000000010000000000000000000000000200000000000000000000000000 [ 7.997650] ... APIC ESR: 00000000 [ 7.997925] ... APIC ICR: 000000ef [ 7.998201] ... APIC ICR2: 07000000 [ 7.998480] ... APIC LVTT: 000000ef [ 7.998759] ... APIC LVTPC: 00000400 [ 7.999041] ... APIC LVT0: 00010700 [ 7.999320] ... APIC LVT1: 00000400 [ 7.999599] ... APIC LVTERR: 000000fe [ 7.999887] ... APIC TMICT: 0003ee1e [ 8.000170] ... APIC TMCCT: 00021b95 [ 8.000452] ... APIC TDCR: 00000003 [ 8.000731] [ 8.000936] number of MP IRQ sources: 15. [ 8.001239] number of IO-APIC #8 registers: 24. [ 8.001558] testing the IO APIC....................... [ 8.001868] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 8.002273] [ 8.002480] IO APIC #8...... [ 8.002737] .... register #00: 08000000 [ 8.003035] ....... : physical APIC id: 08 [ 8.003349] ....... : Delivery Type: 0 [ 8.003648] ....... : LTS : 0 [ 8.003996] .... register #01: 00170020 [ 8.004290] ....... : max redirection entries: 17 [ 8.004628] ....... : PRQ implemented: 0 [ 8.004981] ....... : IO APIC version: 20 [ 8.005294] .... IRQ redirection table: [ 8.005587] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect: [ 8.006018] 00 00 1 0 0 0 0 0 0 00 [ 8.006402] 01 00 0 0 0 0 0 0 0 31 [ 8.006795] 02 00 0 0 0 0 0 0 0 30 [ 8.007205] 03 00 0 0 0 0 0 0 0 33 [ 8.007613] 04 00 0 0 0 0 0 0 0 34 [ 8.008068] 05 00 0 0 0 0 0 0 0 35 [ 8.008478] 06 00 1 0 0 0 0 0 0 36 [ 8.008895] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000 [ 8.008907] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 8.009681] 07 00 0 0 0 0 0 0 0 37 [ 8.010140] 08 00 0 0 0 0 0 0 0 38 [ 8.010522] 09 00 0 1 0 0 0 0 0 39 [ 8.010914] 0a 00 0 0 0 0 0 0 0 3A [ 8.011325] 0b 00 0 0 0 0 0 0 0 3B [ 8.011734] 0c 00 0 0 0 0 0 0 0 3C [ 8.012176] 0d 00 0 0 0 0 0 0 0 3D [ 8.012558] 0e 00 0 0 0 0 0 0 0 3E [ 8.012984] 0f 00 0 0 0 0 0 0 0 3F [ 8.013365] 10 00 0 1 0 1 0 0 0 29 [ 8.013749] 11 00 1 1 0 1 0 0 0 41 [ 8.014138] 12 00 0 1 0 1 0 0 0 91 [ 8.014520] 13 00 0 1 0 1 0 0 0 61 [ 8.014956] 14 00 1 1 0 1 0 0 0 71 [ 8.015340] 15 00 0 1 0 1 0 0 0 A1 [ 8.015722] 16 00 1 1 0 1 0 0 0 A9 [ 8.016137] 17 00 0 1 0 1 0 0 0 99 [ 8.016546] IRQ to pin mappings: [ 8.016904] IRQ0 -> 0:2 [ 8.017240] IRQ1 -> 0:1 [ 8.017565] IRQ3 -> 0:3 [ 8.017909] IRQ4 -> 0:4 [ 8.018273] IRQ5 -> 0:5 [ 8.018597] IRQ6 -> 0:6 [ 8.018945] IRQ7 -> 0:7 [ 8.019254] IRQ8 -> 0:8 [ 8.019580] IRQ9 -> 0:9 [ 8.019940] IRQ10 -> 0:10 [ 8.020258] IRQ11 -> 0:11 [ 8.020576] IRQ12 -> 0:12 [ 8.020936] IRQ13 -> 0:13 [ 8.021254] IRQ14 -> 0:14 [ 8.021572] IRQ15 -> 0:15 [ 8.021980] IRQ16 -> 0:16 [ 8.022297] IRQ17 -> 0:17 [ 8.022615] IRQ18 -> 0:18 [ 8.022956] IRQ19 -> 0:19 [ 8.023272] IRQ20 -> 0:20 [ 8.023587] IRQ21 -> 0:21 [ 8.023948] IRQ22 -> 0:22 [ 8.024263] IRQ23 -> 0:23 [ 8.024581] .................................... done. [ 8.025356] PM: Hibernation image not present or could not be loaded. [ 8.025826] registered taskstats version 1 [ 8.026933] Magic number: 7:914:390 [ 8.027231] usb usb8: hash matches [ 8.027596] thermal cooling_device5: hash matches [ 8.028164] rtc_cmos 00:02: setting system clock to 2011-08-17 17:22:31 UTC (1313601751) [ 8.043862] IP-Config: Complete: [ 8.044140] device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1, [ 8.044685] host=fat, domain=, nis-domain=(none), [ 8.045125] bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath= [ 8.060160] ehci_hcd 0000:00:1a.7: port 1 high speed [ 8.060533] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 8.111899] usb 1-1: new high speed USB device number 2 using ehci_hcd [ 8.165163] ehci_hcd 0000:00:1a.7: port 1 high speed [ 8.165521] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 8.235935] usb 1-1: default language 0x0409 [ 8.243130] usb 1-1: udev 2, busnum 1, minor = 1 [ 8.243479] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780 [ 8.243917] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 8.244355] usb 1-1: Product: AX88178 [ 8.244661] usb 1-1: Manufacturer: ASIX Elec. Corp. [ 8.245031] usb 1-1: SerialNumber: 000013 [ 8.245687] usb 1-1: usb_probe_device [ 8.246000] usb 1-1: configuration #1 chosen from 1 choice [ 8.246998] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 8.248228] asix 1-1:1.0: usb_probe_interface [ 8.248550] asix 1-1:1.0: usb_probe_interface - got id [ 8.950889] usb usb5: suspend_rh (auto-stop) [ 8.950894] usb usb8: suspend_rh (auto-stop) [ 8.951575] usb usb6: suspend_rh (auto-stop) [ 8.951933] usb usb7: suspend_rh (auto-stop) [ 8.960911] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83 [ 8.961640] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002' [ 8.962185] md: Waiting for all devices to be available before autodetect [ 8.962194] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s [ 8.962208] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion [ 8.963455] md: If you don't use raid, use raid=noautodetect [ 8.964583] md: Autodetecting RAID arrays. [ 8.964912] md: Scanned 0 and added 0 devices. [ 8.965244] md: autorun ... [ 8.965511] md: ... autorun DONE. [ 8.974287] VFS: Mounted root (nfs filesystem) on device 0:15. [ 8.974712] debug: unmapping init memory ffffffff81ebe000..ffffffff82172000 [ 9.012827] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0 ACK POWER OWNER sig=se0 CSC [ 9.013497] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s [ 9.065069] ehci_hcd 0000:00:1a.7: port 4 high speed [ 9.065405] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.116840] usb 1-4: new high speed USB device number 4 using ehci_hcd [ 9.168073] ehci_hcd 0000:00:1a.7: port 4 high speed [ 9.168409] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 9.200864] usb usb4: suspend_rh (auto-stop) [ 9.405019] stty used greatest stack depth: 4544 bytes left [ 9.433568] uname used greatest stack depth: 3872 bytes left [ 9.467285] sed used greatest stack depth: 3728 bytes left [ 9.500917] sh used greatest stack depth: 3696 bytes left [ 9.528509] mountpoint used greatest stack depth: 3600 bytes left [ 9.899966] hostname used greatest stack depth: 3552 bytes left [ 10.170136] usb 1-4: default language 0x0409 [ 10.172003] usb 1-4: udev 4, busnum 1, minor = 3 [ 10.172336] usb 1-4: New USB device found, idVendor=1307, idProduct=0165 [ 10.172735] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 10.173207] usb 1-4: Product: USB Mass Storage Device [ 10.173546] usb 1-4: Manufacturer: Teclast Technology [ 10.173938] usb 1-4: SerialNumber: 0000000000020D [ 10.174388] usb 1-4: usb_probe_device [ 10.174678] usb 1-4: configuration #1 chosen from 1 choice [ 10.175260] usb 1-4: adding 1-4:1.0 (config #1, interface 0) [ 10.175674] usb-storage 1-4:1.0: usb_probe_interface [ 10.176068] usb-storage 1-4:1.0: usb_probe_interface - got id [ 10.176573] scsi9 : usb-storage 1-4:1.0 [ 10.177159] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004' [ 10.177588] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 10.178004] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 10.178372] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00 [ 10.178755] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s [ 10.282853] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 [ 10.384886] usb 3-2: new low speed USB device number 2 using uhci_hcd [ 10.388490] usb 3-2: uhci_result_common: failed with status 440000 [ 10.392488] usb 3-2: uhci_result_common: failed with status 440000 [ 10.396487] usb 3-2: uhci_result_common: failed with status 440000 [ 10.498872] usb 3-2: device descriptor read/64, error -71 [ 10.603493] usb 3-2: uhci_result_common: failed with status 440000 [ 10.607496] usb 3-2: uhci_result_common: failed with status 440000 [ 10.611497] usb 3-2: uhci_result_common: failed with status 440000 [ 10.713892] usb 3-2: device descriptor read/64, error -71 [ 10.916930] usb 3-2: new low speed USB device number 3 using uhci_hcd [ 10.920511] usb 3-2: uhci_result_common: failed with status 440000 [ 10.924524] usb 3-2: uhci_result_common: failed with status 440000 [ 10.928508] usb 3-2: uhci_result_common: failed with status 440000 [ 11.030939] usb 3-2: device descriptor read/64, error -71 [ 11.135517] usb 3-2: uhci_result_common: failed with status 440000 [ 11.139516] usb 3-2: uhci_result_common: failed with status 440000 [ 11.143515] usb 3-2: uhci_result_common: failed with status 440000 [ 11.178223] scsi 9:0:0:0: Direct-Access Teclast CoolFlash 0.00 PQ: 0 ANSI: 2 [ 11.246954] usb 3-2: device descriptor read/64, error -71 [ 11.312824] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB) [ 11.314080] sd 9:0:0:0: [sdb] Write Protect is off [ 11.314424] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 11.315504] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.315887] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.321693] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.322138] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.449925] usb 3-2: new low speed USB device number 4 using uhci_hcd [ 11.453605] usb 3-2: uhci_result_common: failed with status 440000 [ 11.456586] sdb: sdb1 sdb2 sdb3 [ 11.460108] sd 9:0:0:0: [sdb] Asking for cache data failed [ 11.460467] sd 9:0:0:0: [sdb] Assuming drive cache: write through [ 11.460840] sd 9:0:0:0: [sdb] Attached SCSI removable disk [ 11.467289] EXT4-fs (sda5): recovery complete [ 11.467711] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) [ 11.658532] usb 3-2: uhci_result_common: failed with status 440000 [ 11.859958] usb 3-2: device not accepting address 4, error -71 [ 11.961952] usb 3-2: new low speed USB device number 5 using uhci_hcd [ 11.965549] usb 3-2: uhci_result_common: failed with status 440000 [ 12.081311] grep used greatest stack depth: 3344 bytes left [ 12.096016] mount.nfs used greatest stack depth: 3152 bytes left [ 12.170553] usb 3-2: uhci_result_common: failed with status 440000 [ 12.372010] usb 3-2: device not accepting address 5, error -71 [ 12.372422] hub 3-0:1.0: unable to enumerate USB device on port 2 [ 12.372832] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 12.373235] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004 [ 12.373620] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 14.167520] XFS (sda7): Mounting Filesystem [ 14.230058] XFS (sda7): Ending clean mount