[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.1.0-rc1-maxpause-fix+ (wfg@bee) (gcc version 4.5.0 (GCC) ) #199 SMP Tue Aug 16 13:49:29 CST 2011
[    0.000000] Command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1-maxpause-fix+ 
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   Centaur CentaurHauls
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009cc00 (usable)
[    0.000000]  BIOS-e820: 000000000009cc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bcda4000 (usable)
[    0.000000]  BIOS-e820: 00000000bcda4000 - 00000000bcfdd000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bcfdd000 - 00000000bf6bd000 (usable)
[    0.000000]  BIOS-e820: 00000000bf6bd000 - 00000000bf6bf000 (reserved)
[    0.000000]  BIOS-e820: 00000000bf6bf000 - 00000000bf714000 (usable)
[    0.000000]  BIOS-e820: 00000000bf714000 - 00000000bf7bf000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bf7bf000 - 00000000bf7e7000 (usable)
[    0.000000]  BIOS-e820: 00000000bf7e7000 - 00000000bf7ff000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bf7ff000 - 00000000bf800000 (usable)
[    0.000000]  BIOS-e820: 00000000bf800000 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f8000000 - 00000000fd000000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI 2.5 present.
[    0.000000] DMI:                  /DX58SO, BIOS SOX5810J.86A.2127.2008.0914.1638 09/14/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0xbf800 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-DFFFF write-protect
[    0.000000]   E0000-FFFFF uncachable
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 base 080000000 mask FC0000000 write-back
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] Scan SMP from ffff880000000000 for 1024 bytes.
[    0.000000] Scan SMP from ffff88000009fc00 for 1024 bytes.
[    0.000000] Scan SMP from ffff8800000f0000 for 65536 bytes.
[    0.000000] found SMP MP-table at [ffff8800000ff4c0] ff4c0
[    0.000000]   mpc: ff4d0-ff6a8
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] Base memory trampoline at [ffff880000097000] 97000 size 20480
[    0.000000] init_memory_mapping: 0000000000000000-00000000bf800000
[    0.000000]  0000000000 - 00bf800000 page 4k
[    0.000000] kernel direct mapping tables up to bf800000 @ bf0bd000-bf6bd000
[    0.000000] log_buf_len: 8388608
[    0.000000] early log buf free: 258291(98%)
[    0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 INTEL )
[    0.000000] ACPI: XSDT 00000000bf7fe120 0006C (v01 INTEL  DX58SO   0000084F      01000013)
[    0.000000] ACPI: FACP 00000000bf7fd000 000F4 (v03 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI Warning: Optional field Pm2ControlBlock has zero address or length: 0x0000000000000450/0x0 (20110623/tbfadt-560)
[    0.000000] ACPI Warning: Invalid length for Pm2ControlBlock: 0, using default 8 (20110623/tbfadt-610)
[    0.000000] ACPI: DSDT 00000000bf7f8000 043CE (v02 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: FACS 00000000bf726000 00040
[    0.000000] ACPI: APIC 00000000bf7f7000 00138 (v02 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: WDDT 00000000bf7f6000 00040 (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: MCFG 00000000bf7f5000 0003C (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: ASF! 00000000bf7f4000 000AC (v32 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: SSDT 00000000bf7ea000 070AC (v01 INTEL  SSDT  PM 0000084F MSFT 0100000D)
[    0.000000] ACPI: DMAR 00000000bf7e7000 00140 (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: WDTT 00000000bf7f2000 0020C (v01 INTEL  DX58SO   0000084F MSFT 0100000D)
[    0.000000] ACPI: ASPT 00000000bf7f3000 00034 (v04 INTEL  PerfTune 0000084F MSFT 0100000D)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] mapped APIC to ffffffffff5fb000 (        fee00000)
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-00000000bf800000
[    0.000000] Initmem setup node 0 0000000000000000-00000000bf800000
[    0.000000]   NODE_DATA [00000000bf7e2000 - 00000000bf7e6fff]
[    0.000000]  [ffffea0000000000-ffffea00029fffff] PMD -> [ffff8800b9c00000-ffff8800bc5fffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   empty
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[6] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009c
[    0.000000]     0: 0x00000100 -> 0x000bcda4
[    0.000000]     0: 0x000bcfdd -> 0x000bf6bd
[    0.000000]     0: 0x000bf6bf -> 0x000bf714
[    0.000000]     0: 0x000bf7bf -> 0x000bf7e7
[    0.000000]     0: 0x000bf7ff -> 0x000bf800
[    0.000000] On node 0 totalpages: 783502
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 5 pages reserved
[    0.000000]   DMA zone: 3919 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 10668 pages used for memmap
[    0.000000]   DMA32 zone: 768854 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] mapped APIC to ffffffffff5fb000 (        fee00000)
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x04] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x03] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x10] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x11] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x13] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x15] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x17] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x09] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0a] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0b] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0c] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0d] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0e] high level lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x0f] high level lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 8, APIC INT 02
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 8, APIC INT 09
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 8, APIC INT 01
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 8, APIC INT 03
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 8, APIC INT 04
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 8, APIC INT 05
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 8, APIC INT 06
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 8, APIC INT 07
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 8, APIC INT 08
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 8, APIC INT 0a
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 8, APIC INT 0b
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 8, APIC INT 0c
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 8, APIC INT 0d
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 8, APIC INT 0e
[    0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 8, APIC INT 0f
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 16 CPUs, 8 hotplug CPUs
[    0.000000] mapped IOAPIC to ffffffffff5fa000 (fec00000)
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009c000 - 000000000009d000
[    0.000000] PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 00000000bcda4000 - 00000000bcfdd000
[    0.000000] PM: Registered nosave memory: 00000000bf6bd000 - 00000000bf6bf000
[    0.000000] PM: Registered nosave memory: 00000000bf714000 - 00000000bf7bf000
[    0.000000] PM: Registered nosave memory: 00000000bf7e7000 - 00000000bf7ff000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:38000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:16 nr_node_ids:1
[    0.000000] PERCPU: Embedded 475 pages/cpu @ffff8800b7c00000 s1915008 r8192 d22400 u2097152
[    0.000000] pcpu-alloc: s1915008 r8192 d22400 u2097152 alloc=1*2097152
[    0.000000] pcpu-alloc: [0] 00 [0] 01 [0] 02 [0] 03 [0] 04 [0] 05 [0] 06 [0] 07 
[    0.000000] pcpu-alloc: [0] 08 [0] 09 [0] 10 [0] 11 [0] 12 [0] 13 [0] 14 [0] 15 
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 772773
[    0.000000] Policy zone: DMA32
[    0.000000] Kernel command line: hpet=disable run=/home/wfg/ioless-balance_dirty_pages/test-each-fs.sh log_buf_len=8M debug sched_debug apic=debug dynamic_printk drm.debug=6 sysrq_always_enabled panic=10 unknown_nmi_panic=1 nmi_watchdog=panic,lapic load_ramdisk=2 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 netconsole=@:/eth0,6666@192.168.1.1/00:30:48:fe:19:95 ip=192.168.1.52:192.168.1.11:192.168.1.1:255.255.255.0:fat:eth0:none nfsroot=192.168.1.11:/nfsroot/wfg,tcp,v3,nocto,nolock,rsize=524288,wsize=524288 rw BOOT_IMAGE=x86_64/vmlinuz-3.1.0-rc1-maxpause-fix+ 
[    0.000000] sysrq: sysrq always enabled.
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Memory: 3019044k/3137536k available (9445k kernel code, 3528k absent, 114964k reserved, 5641k data, 2768k init)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU debugfs-based tracing is enabled.
[    0.000000] NR_IRQS:4352 nr_irqs:808 16
[    0.000000] Extended CMOS year: 2000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] console [ttyS0] enabled
[    0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[    0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[    0.000000] ... MAX_LOCK_DEPTH:          48
[    0.000000] ... MAX_LOCKDEP_KEYS:        8191
[    0.000000] ... CLASSHASH_SIZE:          4096
[    0.000000] ... MAX_LOCKDEP_ENTRIES:     16384
[    0.000000] ... MAX_LOCKDEP_CHAINS:      32768
[    0.000000] ... CHAINHASH_SIZE:          16384
[    0.000000]  memory used by lock dependency info: 6335 kB
[    0.000000]  per task-struct memory footprint: 2688 bytes
[    0.000000] allocated 25165824 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.001000] Fast TSC calibration using PIT
[    0.002000] Detected 3200.542 MHz processor.
[    0.000004] Calibrating delay loop (skipped), value calculated using timer frequency.. 6401.08 BogoMIPS (lpj=3200542)
[    0.000708] pid_max: default: 32768 minimum: 301
[    0.001932] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.003999] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.005007] Mount-cache hash table entries: 256
[    0.005726] Initializing cgroup subsys debug
[    0.006035] Initializing cgroup subsys cpuacct
[    0.006367] Initializing cgroup subsys memory
[    0.006704] Initializing cgroup subsys devices
[    0.007019] Initializing cgroup subsys freezer
[    0.007343] Initializing cgroup subsys blkio
[    0.007708] CPU: Physical Processor ID: 0
[    0.008006] CPU: Processor Core ID: 0
[    0.008303] mce: CPU supports 9 MCE banks
[    0.008607] CPU0: Thermal monitoring enabled (TM1)
[    0.008943] using mwait in idle threads.
[    0.010091] ACPI: Core revision 20110623
[    0.022072] ftrace: allocating 36036 entries in 142 pages
[    0.030556] Getting VERSION: 60015
[    0.030833] Getting VERSION: 60015
[    0.031119] Getting ID: 0
[    0.031364] Getting ID: 0
[    0.031610] Switched APIC routing to physical flat.
[    0.031940] enabled ExtINT on CPU#0
[    0.032383] ENABLING IO-APIC IRQs
[    0.032654] init IO_APIC IRQs
[    0.032912]  apic 8 pin 0 not connected
[    0.033219] IOAPIC[0]: Set routing entry (8-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:0)
[    0.033782] IOAPIC[0]: Set routing entry (8-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:0)
[    0.034353] IOAPIC[0]: Set routing entry (8-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:0)
[    0.034914] IOAPIC[0]: Set routing entry (8-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:0)
[    0.035479] IOAPIC[0]: Set routing entry (8-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:0)
[    0.036042] IOAPIC[0]: Set routing entry (8-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:0)
[    0.036607] IOAPIC[0]: Set routing entry (8-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:0)
[    0.037172] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0)
[    0.037735] IOAPIC[0]: Set routing entry (8-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:0)
[    0.038301] IOAPIC[0]: Set routing entry (8-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:0)
[    0.038870] IOAPIC[0]: Set routing entry (8-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:0)
[    0.039442] IOAPIC[0]: Set routing entry (8-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:0)
[    0.040010] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0)
[    0.040581] IOAPIC[0]: Set routing entry (8-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:0)
[    0.041152] IOAPIC[0]: Set routing entry (8-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:0)
[    0.041717]  apic 8 pin 16 not connected
[    0.042011]  apic 8 pin 17 not connected
[    0.042307]  apic 8 pin 18 not connected
[    0.042602]  apic 8 pin 19 not connected
[    0.042895]  apic 8 pin 20 not connected
[    0.043192]  apic 8 pin 21 not connected
[    0.043485]  apic 8 pin 22 not connected
[    0.043780]  apic 8 pin 23 not connected
[    0.044210] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.054553] CPU0: Genuine Intel(R) CPU             000  @ 3.20GHz stepping 04
[    0.055036] Using local APIC timer interrupts.
[    0.055037] calibrating APIC timer ...
[    0.156667] ... lapic delta = 833232
[    0.156948] ... PM-Timer delta = 357899
[    0.157237] ... PM-Timer result ok
[    0.157511] ..... delta 833232
[    0.157773] ..... mult: 35792482
[    0.158040] ..... calibration result: 133317
[    0.158347] ..... CPU clock speed is 3199.0617 MHz.
[    0.158676] ..... host bus clock speed is 133.0317 MHz.
[    0.159030] Performance Events: PEBS fmt1+, erratum AAJ80 worked around, Nehalem events, Intel PMU driver.
[    0.159789] ... version:                3
[    0.160090] ... bit width:              48
[    0.160391] ... generic registers:      4
[    0.160688] ... value mask:             0000ffffffffffff
[    0.161035] ... max period:             000000007fffffff
[    0.161380] ... fixed-purpose events:   3
[    0.161677] ... event mask:             000000070000000f
[    0.162410] lockdep: fixing up alternatives.
[    0.162781] Booting Node   0, Processors  #1
[    0.163000] smpboot cpu 1: start_ip = 97000
[    0.174542] masked ExtINT on CPU#1
[    0.254053] lockdep: fixing up alternatives.
[    0.254386]  #2
[    0.254478] smpboot cpu 2: start_ip = 97000
[    0.266017] masked ExtINT on CPU#2
[    0.345690] lockdep: fixing up alternatives.
[    0.346023]  #3
[    0.346116] smpboot cpu 3: start_ip = 97000
[    0.357555] masked ExtINT on CPU#3
[    0.437346] lockdep: fixing up alternatives.
[    0.437683]  #4
[    0.437775] smpboot cpu 4: start_ip = 97000
[    0.449214] masked ExtINT on CPU#4
[    0.529065] lockdep: fixing up alternatives.
[    0.529401]  #5
[    0.529494] smpboot cpu 5: start_ip = 97000
[    0.540941] masked ExtINT on CPU#5
[    0.620742] lockdep: fixing up alternatives.
[    0.621080]  #6
[    0.621173] smpboot cpu 6: start_ip = 97000
[    0.635577] masked ExtINT on CPU#6
[    0.715480] lockdep: fixing up alternatives.
[    0.715816]  #7
[    0.715909] smpboot cpu 7: start_ip = 97000
[    0.727446] masked ExtINT on CPU#7
[    0.806954] Brought up 8 CPUs
[    0.807216] Total of 8 processors activated (51243.30 BogoMIPS).
[    0.810936] CPU0 attaching sched-domain:
[    0.811233]  domain 0: span 0,4 level SIBLING
[    0.811576]   groups: 0 (cpu_power = 589) 4 (cpu_power = 589)
[    0.812562]   domain 1: span 0-7 level MC
[    0.812896]    groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
[    0.813849] CPU1 attaching sched-domain:
[    0.814144]  domain 0: span 1,5 level SIBLING
[    0.814486]   groups: 1 (cpu_power = 589) 5 (cpu_power = 589)
[    0.815018]   domain 1: span 0-7 level MC
[    0.815348]    groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
[    0.816301] CPU2 attaching sched-domain:
[    0.816594]  domain 0: span 2,6 level SIBLING
[    0.816940]   groups: 2 (cpu_power = 589) 6 (cpu_power = 589)
[    0.817468]   domain 1: span 0-7 level MC
[    0.817800]    groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
[    0.818751] CPU3 attaching sched-domain:
[    0.819047]  domain 0: span 3,7 level SIBLING
[    0.819389]   groups: 3 (cpu_power = 589) 7 (cpu_power = 589)
[    0.819920]   domain 1: span 0-7 level MC
[    0.820250]    groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
[    0.821203] CPU4 attaching sched-domain:
[    0.821497]  domain 0: span 0,4 level SIBLING
[    0.821842]   groups: 4 (cpu_power = 589) 0 (cpu_power = 589)
[    0.822371]   domain 1: span 0-7 level MC
[    0.822700]    groups: 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178)
[    0.823653] CPU5 attaching sched-domain:
[    0.823950]  domain 0: span 1,5 level SIBLING
[    0.824293]   groups: 5 (cpu_power = 589) 1 (cpu_power = 589)
[    0.824823]   domain 1: span 0-7 level MC
[    0.825154]    groups: 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178)
[    0.826106] CPU6 attaching sched-domain:
[    0.826401]  domain 0: span 2,6 level SIBLING
[    0.826744]   groups: 6 (cpu_power = 589) 2 (cpu_power = 589)
[    0.827274]   domain 1: span 0-7 level MC
[    0.827605]    groups: 2,6 (cpu_power = 1178) 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178)
[    0.828558] CPU7 attaching sched-domain:
[    0.828854]  domain 0: span 3,7 level SIBLING
[    0.829196]   groups: 7 (cpu_power = 589) 3 (cpu_power = 589)
[    0.829724]   domain 1: span 0-7 level MC
[    0.830056]    groups: 3,7 (cpu_power = 1178) 0,4 (cpu_power = 1178) 1,5 (cpu_power = 1178) 2,6 (cpu_power = 1178)
[    0.831500] kworker/u:0 used greatest stack depth: 5288 bytes left
[    0.833775] PM: Registering ACPI NVS region at bcda4000 (2330624 bytes)
[    0.834263] PM: Registering ACPI NVS region at bf714000 (700416 bytes)
[    0.835379] xor: automatically using best checksumming function: generic_sse
[    0.840706]    generic_sse: 11928.000 MB/sec
[    0.841014] xor: using function: generic_sse (11928.000 MB/sec)
[    0.841462] RTC time:  9:04:39, date: 08/18/11
[    0.841900] NET: Registered protocol family 16
[    0.842969] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.843520] ACPI: bus type pci registered
[    0.844015] dca service started, version 1.12.1
[    0.844410] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[    0.845023] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[    0.858209] PCI: Using configuration type 1 for base access
[    0.880920] bio: create slab <bio-0> at 0
[    0.897520] raid6: int64x1   3171 MB/s
[    0.914465] raid6: int64x2   3406 MB/s
[    0.931399] raid6: int64x4   2738 MB/s
[    0.948348] raid6: int64x8   2101 MB/s
[    0.965282] raid6: sse2x1    7910 MB/s
[    0.982225] raid6: sse2x2    9273 MB/s
[    0.999168] raid6: sse2x4   10539 MB/s
[    0.999456] raid6: using algorithm sse2x4 (10539 MB/s)
[    0.999877] ACPI: Added _OSI(Module Device)
[    1.000191] ACPI: Added _OSI(Processor Device)
[    1.000506] ACPI: Added _OSI(3.0 _SCP Extensions)
[    1.000830] ACPI: Added _OSI(Processor Aggregator Device)
[    1.005136] ACPI: EC: Look up EC in DSDT
[    1.027328] ACPI: Interpreter enabled
[    1.027614] ACPI: (supports S0 S1 S3 S4 S5)
[    1.028125] ACPI: Using IOAPIC for interrupt routing
[    1.040928] ACPI: No dock devices found.
[    1.041230] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    1.042461] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3d])
[    1.044146] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    1.044540] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    1.044933] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    1.045470] pci_root PNP0A03:00: host bridge window [mem 0x000c4000-0x000cbfff]
[    1.046010] pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfedfffff]
[    1.046546] pci_root PNP0A03:00: host bridge window [mem 0xd0000000-0xf7ffffff]
[    1.047108] pci 0000:00:00.0: [8086:3405] type 0 class 0x000600
[    1.047544] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604
[    1.047967] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    1.048349] pci 0000:00:01.0: PME# disabled
[    1.048678] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604
[    1.049107] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[    1.049484] pci 0000:00:03.0: PME# disabled
[    1.049814] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604
[    1.050241] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    1.050618] pci 0000:00:07.0: PME# disabled
[    1.050951] pci 0000:00:10.0: [8086:3425] type 0 class 0x000800
[    1.051398] pci 0000:00:10.1: [8086:3426] type 0 class 0x000800
[    1.051844] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800
[    1.052289] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800
[    1.052733] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800
[    1.053176] pci 0000:00:14.3: [8086:3438] type 0 class 0x000800
[    1.053624] pci 0000:00:19.0: [8086:10cc] type 0 class 0x000200
[    1.054015] pci 0000:00:19.0: reg 10: [mem 0xe0300000-0xe031ffff]
[    1.054399] pci 0000:00:19.0: reg 14: [mem 0xe0323000-0xe0323fff]
[    1.054782] pci 0000:00:19.0: reg 18: [io  0x2100-0x211f]
[    1.055191] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[    1.055568] pci 0000:00:19.0: PME# disabled
[    1.055891] pci 0000:00:1a.0: [8086:3a37] type 0 class 0x000c03
[    1.056316] pci 0000:00:1a.0: reg 20: [io  0x20e0-0x20ff]
[    1.056722] pci 0000:00:1a.1: [8086:3a38] type 0 class 0x000c03
[    1.057146] pci 0000:00:1a.1: reg 20: [io  0x20c0-0x20df]
[    1.057550] pci 0000:00:1a.2: [8086:3a39] type 0 class 0x000c03
[    1.057976] pci 0000:00:1a.2: reg 20: [io  0x20a0-0x20bf]
[    1.058389] pci 0000:00:1a.7: [8086:3a3c] type 0 class 0x000c03
[    1.058778] pci 0000:00:1a.7: reg 10: [mem 0xe0322000-0xe03223ff]
[    1.059239] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[    1.059616] pci 0000:00:1a.7: PME# disabled
[    1.059943] pci 0000:00:1b.0: [8086:3a3e] type 0 class 0x000403
[    1.060331] pci 0000:00:1b.0: reg 10: [mem 0xf7f00000-0xf7f03fff 64bit]
[    1.060792] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    1.061172] pci 0000:00:1b.0: PME# disabled
[    1.061499] pci 0000:00:1c.0: [8086:3a40] type 1 class 0x000604
[    1.061935] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    1.062318] pci 0000:00:1c.0: PME# disabled
[    1.062644] pci 0000:00:1c.1: [8086:3a42] type 1 class 0x000604
[    1.063084] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    1.063460] pci 0000:00:1c.1: PME# disabled
[    1.063791] pci 0000:00:1c.4: [8086:3a48] type 1 class 0x000604
[    1.064231] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    1.064607] pci 0000:00:1c.4: PME# disabled
[    1.064940] pci 0000:00:1d.0: [8086:3a34] type 0 class 0x000c03
[    1.065360] pci 0000:00:1d.0: reg 20: [io  0x2080-0x209f]
[    1.065764] pci 0000:00:1d.1: [8086:3a35] type 0 class 0x000c03
[    1.066187] pci 0000:00:1d.1: reg 20: [io  0x2060-0x207f]
[    1.066589] pci 0000:00:1d.2: [8086:3a36] type 0 class 0x000c03
[    1.067012] pci 0000:00:1d.2: reg 20: [io  0x2040-0x205f]
[    1.067426] pci 0000:00:1d.7: [8086:3a3a] type 0 class 0x000c03
[    1.067814] pci 0000:00:1d.7: reg 10: [mem 0xe0321000-0xe03213ff]
[    1.068276] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    1.068652] pci 0000:00:1d.7: PME# disabled
[    1.068978] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[    1.069420] pci 0000:00:1f.0: [8086:3a16] type 0 class 0x000601
[    1.069886] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    1.070271] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 007f)
[    1.070820] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0810 (mask 007f)
[    1.071415] pci 0000:00:1f.2: [8086:3a22] type 0 class 0x000106
[    1.071803] pci 0000:00:1f.2: reg 10: [io  0x2128-0x212f]
[    1.072162] pci 0000:00:1f.2: reg 14: [io  0x2134-0x2137]
[    1.072518] pci 0000:00:1f.2: reg 18: [io  0x2120-0x2127]
[    1.072874] pci 0000:00:1f.2: reg 1c: [io  0x2130-0x2133]
[    1.073233] pci 0000:00:1f.2: reg 20: [io  0x2020-0x203f]
[    1.073590] pci 0000:00:1f.2: reg 24: [mem 0xe0320000-0xe03207ff]
[    1.074005] pci 0000:00:1f.2: PME# supported from D3hot
[    1.074350] pci 0000:00:1f.2: PME# disabled
[    1.074674] pci 0000:00:1f.3: [8086:3a30] type 0 class 0x000c05
[    1.075063] pci 0000:00:1f.3: reg 10: [mem 0xf7f04000-0xf7f040ff 64bit]
[    1.075481] pci 0000:00:1f.3: reg 20: [io  0x2000-0x201f]
[    1.075907] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    1.076312] pci 0000:02:00.0: [5333:9043] type 0 class 0x000300
[    1.076691] pci 0000:02:00.0: reg 10: [mem 0xe0200000-0xe027ffff]
[    1.077077] pci 0000:02:00.0: reg 14: [mem 0xd0000000-0xdfffffff pref]
[    1.077504] pci 0000:02:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
[    1.077919] pci 0000:02:00.0: supports D1 D2
[    1.081219] pci 0000:02:00.1: [5333:903f] type 0 class 0x000403
[    1.081597] pci 0000:02:00.1: reg 10: [mem 0xe0280000-0xe0283fff]
[    1.082041] pci 0000:02:00.1: supports D1 D2
[    1.082364] pci 0000:00:03.0: PCI bridge to [bus 02-02]
[    1.082710] pci 0000:00:03.0:   bridge window [mem 0xe0200000-0xe02fffff]
[    1.083116] pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.083711] pci 0000:00:07.0: PCI bridge to [bus 03-03]
[    1.084114] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
[    1.084515] pci 0000:00:1c.1: PCI bridge to [bus 05-05]
[    1.084942] pci 0000:06:00.0: [11ab:6121] type 0 class 0x000101
[    1.085331] pci 0000:06:00.0: reg 10: [io  0x1018-0x101f]
[    1.085694] pci 0000:06:00.0: reg 14: [io  0x1024-0x1027]
[    1.086060] pci 0000:06:00.0: reg 18: [io  0x1010-0x1017]
[    1.086423] pci 0000:06:00.0: reg 1c: [io  0x1020-0x1023]
[    1.086786] pci 0000:06:00.0: reg 20: [io  0x1000-0x100f]
[    1.087152] pci 0000:06:00.0: reg 24: [mem 0xe0100000-0xe01003ff]
[    1.087589] pci 0000:06:00.0: supports D1
[    1.087889] pci 0000:06:00.0: PME# supported from D0 D1 D3hot
[    1.088254] pci 0000:06:00.0: PME# disabled
[    1.088577] pci 0000:00:1c.4: PCI bridge to [bus 06-06]
[    1.088924] pci 0000:00:1c.4:   bridge window [io  0x1000-0x1fff]
[    1.089300] pci 0000:00:1c.4:   bridge window [mem 0xe0100000-0xe01fffff]
[    1.089751] pci 0000:07:03.0: [104c:8023] type 0 class 0x000c00
[    1.090141] pci 0000:07:03.0: reg 10: [mem 0xe0004000-0xe00047ff]
[    1.090525] pci 0000:07:03.0: reg 14: [mem 0xe0000000-0xe0003fff]
[    1.090975] pci 0000:07:03.0: supports D1 D2
[    1.091281] pci 0000:07:03.0: PME# supported from D0 D1 D2 D3hot
[    1.091663] pci 0000:07:03.0: PME# disabled
[    1.092022] pci 0000:00:1e.0: PCI bridge to [bus 07-07] (subtractive decode)
[    1.092436] pci 0000:00:1e.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    1.092844] pci 0000:00:1e.0:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    1.093402] pci 0000:00:1e.0:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    1.093961] pci 0000:00:1e.0:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    1.094544] pci 0000:00:1e.0:   bridge window [mem 0x000c4000-0x000cbfff] (subtractive decode)
[    1.095130] pci 0000:00:1e.0:   bridge window [mem 0xfed40000-0xfedfffff] (subtractive decode)
[    1.095713] pci 0000:00:1e.0:   bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode)
[    1.096333] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    1.097688] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[    1.098326] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG1._PRT]
[    1.098797] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG3._PRT]
[    1.099272] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG7._PRT]
[    1.099743] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[    1.100218] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[    1.100700] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[    1.101270]  pci0000:00: Unable to request _OSC control (_OSC support mask: 0x19)
[    1.125215] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    1.126298] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    1.127379] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    1.128461] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    1.129545] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    1.130626] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    1.131712] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    1.132801] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    1.134072] vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=io+mem,locks=none
[    1.134642] vgaarb: loaded
[    1.134898] vgaarb: bridge control possible 0000:02:00.0
[    1.135544] SCSI subsystem initialized
[    1.136002] libata version 3.00 loaded.
[    1.136550] usbcore: registered new interface driver usbfs
[    1.136966] usbcore: registered new interface driver hub
[    1.137381] usbcore: registered new device driver usb
[    1.138155] wmi: Mapper loaded
[    1.138480] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    1.138868] PCI: Using ACPI for IRQ routing
[    1.140744] PCI: Discovered peer bus 3f
[    1.141115] pci 0000:3f:00.0: [8086:2c41] type 0 class 0x000600
[    1.141512] pci 0000:3f:00.1: [8086:2c01] type 0 class 0x000600
[    1.141923] pci 0000:3f:02.0: [8086:2c10] type 0 class 0x000600
[    1.142318] pci 0000:3f:02.1: [8086:2c11] type 0 class 0x000600
[    1.142723] pci 0000:3f:03.0: [8086:2c18] type 0 class 0x000600
[    1.143119] pci 0000:3f:03.1: [8086:2c19] type 0 class 0x000600
[    1.143517] pci 0000:3f:03.4: [8086:2c1c] type 0 class 0x000600
[    1.143918] pci 0000:3f:04.0: [8086:2c20] type 0 class 0x000600
[    1.144315] pci 0000:3f:04.1: [8086:2c21] type 0 class 0x000600
[    1.144713] pci 0000:3f:04.2: [8086:2c22] type 0 class 0x000600
[    1.145110] pci 0000:3f:04.3: [8086:2c23] type 0 class 0x000600
[    1.145508] pci 0000:3f:05.0: [8086:2c28] type 0 class 0x000600
[    1.145910] pci 0000:3f:05.1: [8086:2c29] type 0 class 0x000600
[    1.146305] pci 0000:3f:05.2: [8086:2c2a] type 0 class 0x000600
[    1.146708] pci 0000:3f:05.3: [8086:2c2b] type 0 class 0x000600
[    1.147108] pci 0000:3f:06.0: [8086:2c30] type 0 class 0x000600
[    1.147505] pci 0000:3f:06.1: [8086:2c31] type 0 class 0x000600
[    1.147904] pci 0000:3f:06.2: [8086:2c32] type 0 class 0x000600
[    1.148300] pci 0000:3f:06.3: [8086:2c33] type 0 class 0x000600
[    1.150083] PCI: pci_cache_line_size set to 64 bytes
[    1.150664] reserve RAM buffer: 000000000009cc00 - 000000000009ffff 
[    1.150927] reserve RAM buffer: 00000000bcda4000 - 00000000bfffffff 
[    1.151347] reserve RAM buffer: 00000000bf6bd000 - 00000000bfffffff 
[    1.151770] reserve RAM buffer: 00000000bf714000 - 00000000bfffffff 
[    1.152189] reserve RAM buffer: 00000000bf7e7000 - 00000000bfffffff 
[    1.152607] reserve RAM buffer: 00000000bf800000 - 00000000bfffffff 
[    1.183898] pnp: PnP ACPI init
[    1.184338] ACPI: bus type pnp registered
[    1.185291] pnp 00:00: [bus 00-3d]
[    1.185573] pnp 00:00: [io  0x0cf8-0x0cff]
[    1.185875] pnp 00:00: [io  0x0000-0x0cf7 window]
[    1.186197] pnp 00:00: [io  0x0d00-0xffff window]
[    1.186528] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    1.186878] pnp 00:00: [mem 0x000c4000-0x000cbfff window]
[    1.187226] pnp 00:00: [mem 0xfed40000-0xfedfffff window]
[    1.187583] pnp 00:00: [mem 0xd0000000-0xf7ffffff window]
[    1.187932] pnp 00:00: [mem 0x00000000 window]
[    1.188382] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    1.189065] pnp 00:01: [io  0x0000-0x000f]
[    1.189367] pnp 00:01: [io  0x0081-0x0083]
[    1.189672] pnp 00:01: [io  0x0087]
[    1.189951] pnp 00:01: [io  0x0089-0x008b]
[    1.190252] pnp 00:01: [io  0x008f]
[    1.190533] pnp 00:01: [io  0x00c0-0x00df]
[    1.190836] pnp 00:01: [dma 4]
[    1.191191] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    1.191605] pnp 00:02: [io  0x0070-0x0071]
[    1.191906] pnp 00:02: [io  0x0074-0x0077]
[    1.192210] IOAPIC[0]: Set routing entry (8-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:0)
[    1.192776] pnp 00:02: [irq 8]
[    1.193133] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[    1.193549] pnp 00:03: [io  0x00f0]
[    1.193830] IOAPIC[0]: Set routing entry (8-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:0)
[    1.194397] pnp 00:03: [irq 13]
[    1.194758] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[    1.195169] pnp 00:04: [io  0x0061]
[    1.195547] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    1.195959] pnp 00:05: [io  0x0500-0x053f]
[    1.196260] pnp 00:05: [io  0x0400-0x047f]
[    1.196564] pnp 00:05: [io  0x0092]
[    1.196842] pnp 00:05: [io  0x0680-0x06ff]
[    1.197142] pnp 00:05: [io  0x0010-0x001f]
[    1.197443] pnp 00:05: [io  0x0072-0x0073]
[    1.197746] pnp 00:05: [io  0x0080]
[    1.198024] pnp 00:05: [io  0x0084-0x0086]
[    1.198325] pnp 00:05: [io  0x0088]
[    1.198606] pnp 00:05: [io  0x008c-0x008e]
[    1.198907] pnp 00:05: [io  0x0090-0x009f]
[    1.199386] system 00:05: [io  0x0500-0x053f] has been reserved
[    1.199761] system 00:05: [io  0x0400-0x047f] has been reserved
[    1.200129] system 00:05: [io  0x0680-0x06ff] has been reserved
[    1.200501] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.200982] pnp 00:06: [io  0x0060]
[    1.201263] pnp 00:06: [io  0x0064]
[    1.201715] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    1.202680] pnp 00:07: [mem 0xfec00000-0xfec000ff]
[    1.203117] pnp 00:07: Plug and Play ACPI device, IDs PNP0003 (active)
[    1.203652] pnp: PnP ACPI: found 8 devices
[    1.203954] ACPI: ACPI bus type pnp unregistered
[    1.213827] Switching to clocksource acpi_pm
[    1.214269] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[    1.214487] Switched to NOHz mode on CPU #3
[    1.214510] Switched to NOHz mode on CPU #5
[    1.214512] Switched to NOHz mode on CPU #2
[    1.214520] Switched to NOHz mode on CPU #4
[    1.214557] Switched to NOHz mode on CPU #1
[    1.214562] Switched to NOHz mode on CPU #7
[    1.214573] Switched to NOHz mode on CPU #6
[    1.217014] Switched to NOHz mode on CPU #0
[    1.217369] PCI: max bus depth: 1 pci_try_num: 2
[    1.217745] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    1.218099] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0290000-0xe029ffff pref]
[    1.218638] pci 0000:00:03.0: PCI bridge to [bus 02-02]
[    1.218983] pci 0000:00:03.0:   bridge window [mem 0xe0200000-0xe02fffff]
[    1.222360] pci 0000:00:03.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.222915] pci 0000:00:07.0: PCI bridge to [bus 03-03]
[    1.223265] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
[    1.223627] pci 0000:00:1c.1: PCI bridge to [bus 05-05]
[    1.223979] pci 0000:00:1c.4: PCI bridge to [bus 06-06]
[    1.224336] pci 0000:00:1c.4:   bridge window [io  0x1000-0x1fff]
[    1.224712] pci 0000:00:1c.4:   bridge window [mem 0xe0100000-0xe01fffff]
[    1.225118] pci 0000:00:1e.0: PCI bridge to [bus 07-07]
[    1.225474] pci 0000:00:1e.0:   bridge window [mem 0xe0000000-0xe00fffff]
[    1.225893] IOAPIC[0]: Set routing entry (8-16 -> 0x29 -> IRQ 16 Mode:1 Active:1 Dest:0)
[    1.226477] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.226876] pci 0000:00:01.0: setting latency timer to 64
[    1.227230] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.227635] pci 0000:00:03.0: setting latency timer to 64
[    1.227988] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.228401] pci 0000:00:07.0: setting latency timer to 64
[    1.228760] IOAPIC[0]: Set routing entry (8-17 -> 0x41 -> IRQ 17 Mode:1 Active:1 Dest:0)
[    1.229339] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.229739] pci 0000:00:1c.0: setting latency timer to 64
[    1.230093] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    1.230506] pci 0000:00:1c.1: setting latency timer to 64
[    1.230859] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.231272] pci 0000:00:1c.4: setting latency timer to 64
[    1.231626] pci 0000:00:1e.0: setting latency timer to 64
[    1.231976] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    1.232345] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    1.232701] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    1.233083] pci_bus 0000:00: resource 7 [mem 0x000c4000-0x000cbfff]
[    1.233478] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfedfffff]
[    1.233860] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xf7ffffff]
[    1.234254] pci_bus 0000:02: resource 1 [mem 0xe0200000-0xe02fffff]
[    1.234635] pci_bus 0000:02: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    1.235167] pci_bus 0000:06: resource 0 [io  0x1000-0x1fff]
[    1.235527] pci_bus 0000:06: resource 1 [mem 0xe0100000-0xe01fffff]
[    1.235908] pci_bus 0000:07: resource 1 [mem 0xe0000000-0xe00fffff]
[    1.236302] pci_bus 0000:07: resource 4 [io  0x0000-0x0cf7]
[    1.236656] pci_bus 0000:07: resource 5 [io  0x0d00-0xffff]
[    1.237010] pci_bus 0000:07: resource 6 [mem 0x000a0000-0x000bffff]
[    1.237405] pci_bus 0000:07: resource 7 [mem 0x000c4000-0x000cbfff]
[    1.237785] pci_bus 0000:07: resource 8 [mem 0xfed40000-0xfedfffff]
[    1.238165] pci_bus 0000:07: resource 9 [mem 0xd0000000-0xf7ffffff]
[    1.238551] pci_bus 0000:3f: resource 0 [io  0x0000-0xffff]
[    1.238906] pci_bus 0000:3f: resource 1 [mem 0x00000000-0xfffffffff]
[    1.239454] NET: Registered protocol family 2
[    1.240116] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    1.242650] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    1.246420] TCP bind hash table entries: 65536 (order: 10, 5242880 bytes)
[    1.249805] TCP: Hash tables configured (established 524288 bind 65536)
[    1.250230] TCP reno registered
[    1.250565] UDP hash table entries: 2048 (order: 6, 393216 bytes)
[    1.251201] UDP-Lite hash table entries: 2048 (order: 6, 393216 bytes)
[    1.251992] NET: Registered protocol family 1
[    1.252584] RPC: Registered named UNIX socket transport module.
[    1.252954] RPC: Registered udp transport module.
[    1.253294] RPC: Registered tcp transport module.
[    1.253618] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.254048] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x0f10
[    1.254445] pci 0000:00:1a.0: Performing full reset
[    1.254792] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x0010
[    1.255192] pci 0000:00:1a.1: Performing full reset
[    1.255537] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x0010
[    1.255928] pci 0000:00:1a.2: Performing full reset
[    1.256434] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f10
[    1.256825] pci 0000:00:1d.0: Performing full reset
[    1.257195] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0010
[    1.257586] pci 0000:00:1d.1: Performing full reset
[    1.257931] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0010
[    1.258329] pci 0000:00:1d.2: Performing full reset
[    1.258818] pci 0000:02:00.0: Boot video device
[    1.259203] PCI: CLS 64 bytes, default 64
[    1.263421] Machine check injector initialized
[    1.265288] microcode: CPU0 sig=0x106a4, pf=0x2, revision=0x6
[    1.265660] microcode: CPU1 sig=0x106a4, pf=0x2, revision=0x6
[    1.266033] microcode: CPU2 sig=0x106a4, pf=0x2, revision=0x6
[    1.266403] microcode: CPU3 sig=0x106a4, pf=0x2, revision=0x6
[    1.266773] microcode: CPU4 sig=0x106a4, pf=0x2, revision=0x6
[    1.267155] microcode: CPU5 sig=0x106a4, pf=0x2, revision=0x6
[    1.267524] microcode: CPU6 sig=0x106a4, pf=0x2, revision=0x6
[    1.267894] microcode: CPU7 sig=0x106a4, pf=0x2, revision=0x6
[    1.268345] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    1.269427] audit: initializing netlink socket (disabled)
[    1.269805] type=2000 audit(1313658279.023:1): initialized
[    1.300271] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.302231] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.302946] fuse init (API version 7.16)
[    1.303453] JFS: nTxBlock = 8192, nTxLock = 65536
[    1.306931] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    1.308298] NILFS version 2 loaded
[    1.308873] Btrfs loaded
[    1.309136] msgmni has been set to 5896
[    1.310283] async_tx: api initialized (async)
[    1.310694] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.311302] io scheduler noop registered
[    1.311597] io scheduler deadline registered
[    1.311955] io scheduler cfq registered (default)
[    1.312725] pcieport 0000:00:1c.0: setting latency timer to 64
[    1.313159] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[    1.313634] pcieport 0000:00:1c.1: setting latency timer to 64
[    1.314062] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[    1.314536] pcieport 0000:00:1c.4: setting latency timer to 64
[    1.314948] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X
[    1.315665] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.316487] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input0
[    1.317084] ACPI: Sleep Button [SLPB]
[    1.317504] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    1.318062] ACPI: Power Button [PWRF]
[    1.319089] ACPI: acpi_idle registered with cpuidle
[    1.319838] Monitor-Mwait will be used to enter C-1 state
[    1.320252] Monitor-Mwait will be used to enter C-3 state
[    1.328023] ioatdma: Intel(R) QuickData Technology Driver 4.00
[    1.372154] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.387868] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[    1.436918] Initializing Nozomi driver 2.1d
[    1.437726] Non-volatile memory driver v1.3
[    1.438469] Linux agpgart interface v0.103
[    1.438867] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[    1.439464] Hangcheck: Using getrawmonotonic().
[    1.439858] [drm] Initialized drm 1.1.0 20060810
[    1.440179] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module!
[    2.258135] Refined TSC clocksource calibration: 3200.113 MHz.
[    2.258503] Switching to clocksource tsc
[    4.443413] floppy0: no floppy controllers found
[    4.574865] brd: module loaded
[    4.576670] loop: module loaded
[    4.577423] Loading iSCSI transport class v2.0-870.
[    4.578348] Loading Adaptec I2O RAID: Version 2.4 Build 5go
[    4.578703] Detecting Adaptec I2O RAID controllers...
[    4.579227] Adaptec aacraid driver 1.1-7[28000]-ms
[    4.580114] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[    4.580736] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.03-k.
[    4.581479] iscsi: registered transport (qla4xxx)
[    4.581882] QLogic iSCSI HBA Driver
[    4.582240] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[    4.582847] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[    4.583337] megasas: 00.00.05.40-rc1 Tue. Jul. 26 17:00:00 PDT 2011
[    4.583800] mpt2sas version 09.100.00.00 loaded
[    4.584516] ahci 0000:00:1f.2: version 3.0
[    4.584848] IOAPIC[0]: Set routing entry (8-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:0)
[    4.585420] ahci 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    4.585873] ahci 0000:00:1f.2: irq 43 for MSI/MSI-X
[    4.586287] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[    4.586859] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems 
[    4.587419] ahci 0000:00:1f.2: setting latency timer to 64
[    4.598160] scsi0 : ahci
[    4.598624] scsi1 : ahci
[    4.599034] scsi2 : ahci
[    4.599432] scsi3 : ahci
[    4.599830] scsi4 : ahci
[    4.600229] scsi5 : ahci
[    4.600898] ata1: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320100 irq 43
[    4.601441] ata2: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320180 irq 43
[    4.601984] ata3: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320200 irq 43
[    4.602523] ata4: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320280 irq 43
[    4.603065] ata5: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320300 irq 43
[    4.603606] ata6: SATA max UDMA/133 abar m2048@0xe0320000 port 0xe0320380 irq 43
[    4.604177] ahci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.607560] ahci 0000:06:00.0: Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.
[    4.608221] ahci 0000:06:00.0: controller can't do NCQ, turning off CAP_NCQ
[    4.608627] ahci 0000:06:00.0: controller can't do PMP, turning off CAP_PMP
[    4.609035] ahci 0000:06:00.0: masking port_map 0x7 -> 0x3
[    4.609405] ahci: SSS flag set, parallel bus scan disabled
[    4.609799] ahci 0000:06:00.0: AHCI 0001.0000 32 slots 3 ports 3 Gbps 0x3 impl IDE mode
[    4.610360] ahci 0000:06:00.0: flags: 64bit stag led slum part 
[    4.610731] ahci 0000:06:00.0: setting latency timer to 64
[    4.611979] scsi6 : ahci
[    4.612388] scsi7 : ahci
[    4.612856] scsi8 : ahci
[    4.613238] ata7: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100100 irq 16
[    4.613782] ata8: SATA max UDMA/133 abar m1024@0xe0100000 port 0xe0100180 irq 16
[    4.614320] ata9: DUMMY
[    4.616552] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[    4.616965] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    4.617406] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.16-k
[    4.617777] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[    4.618176] IOAPIC[0]: Set routing entry (8-20 -> 0x71 -> IRQ 20 Mode:1 Active:1 Dest:0)
[    4.618743] e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    4.619157] e1000e 0000:00:19.0: setting latency timer to 64
[    4.619624] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    4.809663] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:c0:79:88:54
[    4.810230] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    4.810665] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: FFFFFF-0FF
[    4.811140] Intel(R) Gigabit Ethernet Network Driver - version 3.0.6-k
[    4.811534] Copyright (c) 2007-2011 Intel Corporation.
[    4.811954] Intel(R) Virtual Function Network Driver - version 2.0.0-k
[    4.812351] Copyright (c) 2009 - 2010 Intel Corporation.
[    4.812773] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 3.4.8-k
[    4.813324] ixgbe: Copyright (c) 1999-2011 Intel Corporation.
[    4.813760] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[    4.814176] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[    4.814899] jme: JMicron JMC2XX ethernet driver version 1.0.8
[    4.815337] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[    4.815712] e100: Copyright(c) 1999-2006 Intel Corporation
[    4.816363] ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
[    4.816982] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.5.7 (July 20, 2011)
[    4.817637] sky2: driver version 1.29
[    4.818932] tun: Universal TUN/TAP device driver, 1.6
[    4.819273] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    4.819932] usbcore: registered new interface driver catc
[    4.820286] catc: v2.8:CATC EL1210A NetMate USB Ethernet driver
[    4.820707] usbcore: registered new interface driver kaweth
[    4.821063] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[    4.821664] usbcore: registered new interface driver pegasus
[    4.822024] rtl8150: v0.6.2 (2004/08/27):rtl8150 based usb-ethernet driver
[    4.822483] usbcore: registered new interface driver rtl8150
[    4.822887] usbcore: registered new interface driver asix
[    4.823290] usbcore: registered new interface driver cdc_ether
[    4.823703] usbcore: registered new interface driver cdc_eem
[    4.824109] usbcore: registered new interface driver dm9601
[    4.824528] usbcore: registered new interface driver smsc75xx
[    4.824943] usbcore: registered new interface driver smsc95xx
[    4.825362] usbcore: registered new interface driver gl620a
[    4.825767] usbcore: registered new interface driver net1080
[    4.826179] usbcore: registered new interface driver plusb
[    4.826580] usbcore: registered new interface driver rndis_host
[    4.826995] usbcore: registered new interface driver cdc_subset
[    4.827418] usbcore: registered new interface driver zaurus
[    4.827820] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    4.828419] usbcore: registered new interface driver int51x1
[    4.828777] cdc_ncm: 04-Aug-2011
[    4.829094] usbcore: registered new interface driver cdc_ncm
[    4.829458] netconsole: local port 6665
[    4.829749] netconsole: local IP 10.0.0.0
[    4.830046] netconsole: interface 'eth0'
[    4.830346] netconsole: remote port 6666
[    4.830641] netconsole: remote IP 192.168.1.1
[    4.830950] netconsole: remote ethernet address 00:30:48:fe:19:95
[    4.831330] netconsole: device eth0 not up yet, forcing it
[    4.907887] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    4.908284] ata4: SATA link down (SStatus 0 SControl 300)
[    4.908664] ata5: SATA link down (SStatus 0 SControl 300)
[    4.909040] ata3: SATA link down (SStatus 0 SControl 300)
[    4.909409] ata6: SATA link down (SStatus 0 SControl 300)
[    4.917861] ata7: SATA link down (SStatus 0 SControl 300)
[    4.926299] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    4.949202] ata1.00: ATA-7: ST3320620AS, 3.AAE, max UDMA/133
[    4.949561] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    4.976713] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    5.007329] ata1.00: configured for UDMA/133
[    5.007825] scsi 0:0:0:0: Direct-Access     ATA      ST3320620AS      3.AA PQ: 0 ANSI: 5
[    5.008721] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[    5.009341] sd 0:0:0:0: [sda] Write Protect is off
[    5.009678] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.010049] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.099074]  sda: sda1 sda2 sda4 < sda5 sda6 sda7 sda8 sda9 >
[    5.100322] sd 0:0:0:0: [sda] Attached SCSI disk
[    5.263796] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.342440] ata2.00: ATAPI: PLEXTOR DVDR   PX-712A, 1.07, max UDMA/33
[    5.342836] ata2.00: applying bridge limits
[    5.373595] ata2.00: configured for UDMA/33
[    5.374903] scsi 1:0:0:0: CD-ROM            PLEXTOR  DVDR   PX-712A   1.07 PQ: 0 ANSI: 5
[    5.679511] ata8: SATA link down (SStatus 0 SControl 300)
[    7.811788] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[    7.815232] console [netcon0] enabled
[    7.815521] netconsole: network logging started
[    7.815908] Fusion MPT base driver 3.04.19
[    7.816211] Copyright (c) 1999-2008 LSI Corporation
[    7.816552] Fusion MPT SPI Host driver 3.04.19
[    7.816958] Fusion MPT FC Host driver 3.04.19
[    7.817354] Fusion MPT SAS Host driver 3.04.19
[    7.817755] Fusion MPT misc device (ioctl) driver 3.04.19
[    7.818183] mptctl: Registered with Fusion MPT base driver
[    7.818539] mptctl: /dev/mptctl @ (major,minor=10,220)
[    7.818982] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.819375] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96
[    7.819795] IOAPIC[0]: Set routing entry (8-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:0)
[    7.820370] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    7.820802] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    7.821175] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    7.821588] /c/wfg/linux/drivers/usb/core/inode.c: creating file 'devices'
[    7.822012] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.822417] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    7.822971] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[    7.823570] ehci_hcd 0000:00:1a.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch
[    7.824224] ehci_hcd 0000:00:1a.7: debug port 1
[    7.824544] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.829009] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[    7.829410] ehci_hcd 0000:00:1a.7: supports USB remote wakeup
[    7.829794] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xe0322000
[    7.830161] ehci_hcd 0000:00:1a.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.834633] ehci_hcd 0000:00:1a.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[    7.840781] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    7.841231] usb usb1: default language 0x0409
[    7.841554] usb usb1: udev 1, busnum 1, minor = 0
[    7.841885] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.842286] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.842823] usb usb1: Product: EHCI Host Controller
[    7.843154] usb usb1: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ ehci_hcd
[    7.843559] usb usb1: SerialNumber: 0000:00:1a.7
[    7.844007] usb usb1: usb_probe_device
[    7.844299] usb usb1: configuration #1 chosen from 1 choice
[    7.844682] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[    7.845133] hub 1-0:1.0: usb_probe_interface
[    7.845444] hub 1-0:1.0: usb_probe_interface - got id
[    7.845787] hub 1-0:1.0: USB hub found
[    7.846082] hub 1-0:1.0: 6 ports detected
[    7.846383] hub 1-0:1.0: standalone hub
[    7.846676] hub 1-0:1.0: no power switching (usb 1.0)
[    7.847017] hub 1-0:1.0: individual port over-current protection
[    7.847391] hub 1-0:1.0: power on to power good time: 20ms
[    7.847766] hub 1-0:1.0: local power source is good
[    7.848100] hub 1-0:1.0: trying to enable port power on non-switchable hub
[    7.848554] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.849073] IOAPIC[0]: Set routing entry (8-23 -> 0x99 -> IRQ 23 Mode:1 Active:1 Dest:0)
[    7.849645] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    7.850076] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    7.850446] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    7.850799] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002'
[    7.851198] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    7.851752] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
[    7.852353] ehci_hcd 0000:00:1d.7: reset hcc_params 16871 thresh 7 uframes 1024 64 bit addr hw prefetch
[    7.855962] ehci_hcd 0000:00:1d.7: debug port 1
[    7.856283] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.860770] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[    7.861171] ehci_hcd 0000:00:1d.7: supports USB remote wakeup
[    7.861557] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0321000
[    7.861925] ehci_hcd 0000:00:1d.7: reset command 0080002 (park)=0 ithresh=8 period=1024 Reset HALT
[    7.866396] ehci_hcd 0000:00:1d.7: init command 0010001 (park)=0 ithresh=1 period=1024 RUN
[    7.872682] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    7.873089] usb usb2: default language 0x0409
[    7.873411] usb usb2: udev 1, busnum 2, minor = 128
[    7.873747] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    7.874149] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.874686] usb usb2: Product: EHCI Host Controller
[    7.875018] usb usb2: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ ehci_hcd
[    7.875423] usb usb2: SerialNumber: 0000:00:1d.7
[    7.875864] usb usb2: usb_probe_device
[    7.876156] usb usb2: configuration #1 chosen from 1 choice
[    7.876520] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[    7.876951] hub 2-0:1.0: usb_probe_interface
[    7.877260] hub 2-0:1.0: usb_probe_interface - got id
[    7.877597] hub 2-0:1.0: USB hub found
[    7.877896] hub 2-0:1.0: 6 ports detected
[    7.878196] hub 2-0:1.0: standalone hub
[    7.878489] hub 2-0:1.0: no power switching (usb 1.0)
[    7.878829] hub 2-0:1.0: individual port over-current protection
[    7.879203] hub 2-0:1.0: power on to power good time: 20ms
[    7.879563] hub 2-0:1.0: local power source is good
[    7.879898] hub 2-0:1.0: trying to enable port power on non-switchable hub
[    7.880349] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.880901] uhci_hcd: USB Universal Host Controller Interface driver
[    7.881338] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    7.881764] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    7.882132] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    7.882485] /c/wfg/linux/drivers/usb/core/inode.c: creating file '003'
[    7.882885] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    7.883433] uhci_hcd 0000:00:1a.0: detected 2 ports
[    7.883772] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000
[    7.884170] uhci_hcd 0000:00:1a.0: Performing full reset
[    7.884529] uhci_hcd 0000:00:1a.0: supports USB remote wakeup
[    7.884900] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000020e0
[    7.885321] usb usb3: default language 0x0409
[    7.885647] usb usb3: udev 1, busnum 3, minor = 256
[    7.885979] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    7.886381] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.886918] usb usb3: Product: UHCI Host Controller
[    7.887250] usb usb3: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ uhci_hcd
[    7.887658] usb usb3: SerialNumber: 0000:00:1a.0
[    7.888111] usb usb3: usb_probe_device
[    7.888403] usb usb3: configuration #1 chosen from 1 choice
[    7.888772] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[    7.889204] hub 3-0:1.0: usb_probe_interface
[    7.889515] hub 3-0:1.0: usb_probe_interface - got id
[    7.889856] hub 3-0:1.0: USB hub found
[    7.890151] hub 3-0:1.0: 2 ports detected
[    7.890451] hub 3-0:1.0: standalone hub
[    7.890749] hub 3-0:1.0: no power switching (usb 1.0)
[    7.891087] hub 3-0:1.0: individual port over-current protection
[    7.891461] hub 3-0:1.0: power on to power good time: 2ms
[    7.891821] hub 3-0:1.0: local power source is good
[    7.892154] hub 3-0:1.0: trying to enable port power on non-switchable hub
[    7.892584] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.893038] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.0
[    7.893476] IOAPIC[0]: Set routing entry (8-21 -> 0xa1 -> IRQ 21 Mode:1 Active:1 Dest:0)
[    7.894051] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    7.894472] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    7.894845] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    7.895199] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004'
[    7.895601] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    7.896151] uhci_hcd 0000:00:1a.1: detected 2 ports
[    7.896485] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000
[    7.896887] uhci_hcd 0000:00:1a.1: Performing full reset
[    7.897246] uhci_hcd 0000:00:1a.1: supports USB remote wakeup
[    7.897633] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000020c0
[    7.898044] usb usb4: default language 0x0409
[    7.898365] usb usb4: udev 1, busnum 4, minor = 384
[    7.898701] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    7.899104] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.899639] usb usb4: Product: UHCI Host Controller
[    7.899970] usb usb4: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ uhci_hcd
[    7.900375] usb usb4: SerialNumber: 0000:00:1a.1
[    7.900814] usb usb4: usb_probe_device
[    7.901106] usb usb4: configuration #1 chosen from 1 choice
[    7.901469] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[    7.901905] hub 4-0:1.0: usb_probe_interface
[    7.902214] hub 4-0:1.0: usb_probe_interface - got id
[    7.902552] hub 4-0:1.0: USB hub found
[    7.902851] hub 4-0:1.0: 2 ports detected
[    7.903151] hub 4-0:1.0: standalone hub
[    7.903444] hub 4-0:1.0: no power switching (usb 1.0)
[    7.903784] hub 4-0:1.0: individual port over-current protection
[    7.904157] hub 4-0:1.0: power on to power good time: 2ms
[    7.904514] hub 4-0:1.0: local power source is good
[    7.904848] hub 4-0:1.0: trying to enable port power on non-switchable hub
[    7.905277] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.905725] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.1
[    7.906156] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    7.906581] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    7.906951] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    7.907303] /c/wfg/linux/drivers/usb/core/inode.c: creating file '005'
[    7.907708] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    7.908260] uhci_hcd 0000:00:1a.2: detected 2 ports
[    7.908598] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000
[    7.908997] uhci_hcd 0000:00:1a.2: Performing full reset
[    7.909357] uhci_hcd 0000:00:1a.2: supports USB remote wakeup
[    7.909746] uhci_hcd 0000:00:1a.2: irq 19, io base 0x000020a0
[    7.910150] usb usb5: default language 0x0409
[    7.910472] usb usb5: udev 1, busnum 5, minor = 512
[    7.910809] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    7.911212] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.911751] usb usb5: Product: UHCI Host Controller
[    7.912083] usb usb5: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ uhci_hcd
[    7.912488] usb usb5: SerialNumber: 0000:00:1a.2
[    7.912930] usb usb5: usb_probe_device
[    7.913223] usb usb5: configuration #1 chosen from 1 choice
[    7.913592] usb usb5: adding 5-0:1.0 (config #1, interface 0)
[    7.914022] hub 5-0:1.0: usb_probe_interface
[    7.914332] hub 5-0:1.0: usb_probe_interface - got id
[    7.914672] hub 5-0:1.0: USB hub found
[    7.914966] hub 5-0:1.0: 2 ports detected
[    7.915265] hub 5-0:1.0: standalone hub
[    7.915561] hub 5-0:1.0: no power switching (usb 1.0)
[    7.915898] hub 5-0:1.0: individual port over-current protection
[    7.916271] hub 5-0:1.0: power on to power good time: 2ms
[    7.916630] hub 5-0:1.0: local power source is good
[    7.916961] hub 5-0:1.0: trying to enable port power on non-switchable hub
[    7.917389] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.917836] ehci_hcd 0000:00:1a.7: HS companion for 0000:00:1a.2
[    7.918267] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    7.918701] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    7.919069] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    7.919422] /c/wfg/linux/drivers/usb/core/inode.c: creating file '006'
[    7.919823] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    7.920371] uhci_hcd 0000:00:1d.0: detected 2 ports
[    7.920709] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000
[    7.921108] uhci_hcd 0000:00:1d.0: Performing full reset
[    7.921467] uhci_hcd 0000:00:1d.0: supports USB remote wakeup
[    7.921837] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080
[    7.922247] usb usb6: default language 0x0409
[    7.922572] usb usb6: udev 1, busnum 6, minor = 640
[    7.922903] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    7.923304] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.923841] usb usb6: Product: UHCI Host Controller
[    7.924174] usb usb6: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ uhci_hcd
[    7.924583] usb usb6: SerialNumber: 0000:00:1d.0
[    7.925022] usb usb6: usb_probe_device
[    7.925314] usb usb6: configuration #1 chosen from 1 choice
[    7.925683] usb usb6: adding 6-0:1.0 (config #1, interface 0)
[    7.926114] hub 6-0:1.0: usb_probe_interface
[    7.926425] hub 6-0:1.0: usb_probe_interface - got id
[    7.926768] hub 6-0:1.0: USB hub found
[    7.927064] hub 6-0:1.0: 2 ports detected
[    7.927364] hub 6-0:1.0: standalone hub
[    7.927660] hub 6-0:1.0: no power switching (usb 1.0)
[    7.927997] hub 6-0:1.0: individual port over-current protection
[    7.928371] hub 6-0:1.0: power on to power good time: 2ms
[    7.928767] hub 6-0:1.0: local power source is good
[    7.929099] hub 6-0:1.0: trying to enable port power on non-switchable hub
[    7.929533] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.929989] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.0
[    7.930411] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    7.930835] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    7.931204] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    7.931559] /c/wfg/linux/drivers/usb/core/inode.c: creating file '007'
[    7.931957] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    7.932509] uhci_hcd 0000:00:1d.1: detected 2 ports
[    7.935812] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000
[    7.936209] uhci_hcd 0000:00:1d.1: Performing full reset
[    7.936571] uhci_hcd 0000:00:1d.1: supports USB remote wakeup
[    7.936939] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
[    7.937345] usb usb7: default language 0x0409
[    7.937672] usb usb7: udev 1, busnum 7, minor = 768
[    7.938003] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    7.938406] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.938942] usb usb7: Product: UHCI Host Controller
[    7.939274] usb usb7: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ uhci_hcd
[    7.939682] usb usb7: SerialNumber: 0000:00:1d.1
[    7.940119] usb usb7: usb_probe_device
[    7.940409] usb usb7: configuration #1 chosen from 1 choice
[    7.940777] usb usb7: adding 7-0:1.0 (config #1, interface 0)
[    7.941210] hub 7-0:1.0: usb_probe_interface
[    7.941525] hub 7-0:1.0: usb_probe_interface - got id
[    7.941862] hub 7-0:1.0: USB hub found
[    7.942156] hub 7-0:1.0: 2 ports detected
[    7.942459] hub 7-0:1.0: standalone hub
[    7.942751] hub 7-0:1.0: no power switching (usb 1.0)
[    7.943088] hub 7-0:1.0: individual port over-current protection
[    7.943464] hub 7-0:1.0: power on to power good time: 2ms
[    7.943819] hub 7-0:1.0: local power source is good
[    7.944151] hub 7-0:1.0: trying to enable port power on non-switchable hub
[    7.944584] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.945041] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.1
[    7.945465] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    7.945886] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    7.946253] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    7.946611] /c/wfg/linux/drivers/usb/core/inode.c: creating file '008'
[    7.947008] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    7.947581] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001803 0  ACK POWER sig=j CSC CONNECT
[    7.948175] hub 1-0:1.0: port 1: status 0501 change 0001
[    7.948538] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 001403 0  ACK POWER sig=k CSC CONNECT
[    7.948545] uhci_hcd 0000:00:1d.2: detected 2 ports
[    7.948550] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000
[    7.948552] uhci_hcd 0000:00:1d.2: Performing full reset
[    7.948565] uhci_hcd 0000:00:1d.2: supports USB remote wakeup
[    7.948573] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
[    7.948636] usb usb8: default language 0x0409
[    7.948648] usb usb8: udev 1, busnum 8, minor = 896
[    7.948650] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[    7.948652] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.948654] usb usb8: Product: UHCI Host Controller
[    7.948656] usb usb8: Manufacturer: Linux 3.1.0-rc1-maxpause-fix+ uhci_hcd
[    7.948658] usb usb8: SerialNumber: 0000:00:1d.2
[    7.948818] usb usb8: usb_probe_device
[    7.948821] usb usb8: configuration #1 chosen from 1 choice
[    7.948832] usb usb8: adding 8-0:1.0 (config #1, interface 0)
[    7.948934] hub 8-0:1.0: usb_probe_interface
[    7.948937] hub 8-0:1.0: usb_probe_interface - got id
[    7.948939] hub 8-0:1.0: USB hub found
[    7.948947] hub 8-0:1.0: 2 ports detected
[    7.948950] hub 8-0:1.0: standalone hub
[    7.948951] hub 8-0:1.0: no power switching (usb 1.0)
[    7.948953] hub 8-0:1.0: individual port over-current protection
[    7.948955] hub 8-0:1.0: power on to power good time: 2ms
[    7.948966] hub 8-0:1.0: local power source is good
[    7.948969] hub 8-0:1.0: trying to enable port power on non-switchable hub
[    7.949016] /c/wfg/linux/drivers/usb/core/inode.c: creating file '001'
[    7.949135] ehci_hcd 0000:00:1d.7: HS companion for 0000:00:1d.2
[    7.949261] Initializing USB Mass Storage driver...
[    7.949356] usbcore: registered new interface driver usb-storage
[    7.949367] USB Mass Storage support registered.
[    7.949514] usbcore: registered new interface driver libusual
[    7.949578] usbcore: registered new interface driver ums-alauda
[    7.949657] usbcore: registered new interface driver ums-cypress
[    7.949727] usbcore: registered new interface driver ums-datafab
[    7.949799] usbcore: registered new interface driver ums-freecom
[    7.949875] usbcore: registered new interface driver ums-isd200
[    7.949943] usbcore: registered new interface driver ums-jumpshot
[    7.950005] usbcore: registered new interface driver ums-karma
[    7.950069] usbcore: registered new interface driver ums-onetouch
[    7.950142] usbcore: registered new interface driver ums-sddr09
[    7.950218] usbcore: registered new interface driver ums-sddr55
[    7.950288] usbcore: registered new interface driver ums-usbat
[    7.950436] usbcore: registered new interface driver usbserial
[    7.950523] USB Serial support registered for generic
[    7.950612] usbcore: registered new interface driver usbserial_generic
[    7.950614] usbserial: USB Serial Driver core
[    7.950673] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[    7.950746] usbcore: registered new interface driver belkin
[    7.950748] belkin_sa: v1.3:USB Belkin Serial converter driver
[    7.950804] USB Serial support registered for MCT U232
[    7.950891] usbcore: registered new interface driver mct_u232
[    7.950894] mct_u232: z2.1:Magic Control Technology USB-RS232 converter driver
[    7.951128] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    7.954425] serio: i8042 KBD port at 0x60,0x64 irq 1
[    7.954445] serio: i8042 AUX port at 0x60,0x64 irq 12
[    7.954732] mousedev: PS/2 mouse device common for all mice
[    7.955364] rtc_cmos 00:02: RTC can wake from S4
[    7.955650] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    7.955708] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    7.955770] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[    7.956020] iTCO_wdt: Found a ICH10R TCO device (Version=2, TCOBASE=0x0460)
[    7.956164] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    7.956168] iTCO_vendor_support: vendor-support=0
[    7.956171] SoftDog: cannot register miscdev on minor=130 (err=-16)
[    7.956181] md: linear personality registered for level -1
[    7.956183] md: raid0 personality registered for level 0
[    7.956185] md: raid1 personality registered for level 1
[    7.956187] md: raid10 personality registered for level 10
[    7.956189] md: raid6 personality registered for level 6
[    7.956191] md: raid5 personality registered for level 5
[    7.956193] md: raid4 personality registered for level 4
[    7.956195] md: multipath personality registered for level -4
[    7.956197] md: faulty personality registered for level -5
[    7.975953] hub 1-0:1.0: port 2: status 0501 change 0001
[    7.976317] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001803 0  ACK POWER sig=j CSC CONNECT
[    7.976919] hub 1-0:1.0: port 4: status 0501 change 0001
[    7.977279] device-mapper: uevent: version 1.0.3
[    7.977740] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06) initialised: dm-devel@redhat.com
[    7.978470] device-mapper: multipath: version 1.3.0 loaded
[    7.978832] device-mapper: multipath round-robin: version 1.0.0 loaded
[    7.979225] device-mapper: multipath queue-length: version 0.1.0 loaded
[    7.979373] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0000
[    7.979981] device-mapper: multipath service-time: version 0.2.0 loaded
[    7.980475] device-mapper: dm-log-userspace: version 1.1.0 loaded
[    7.982163] cpuidle: using governor ladder
[    7.985112] cpuidle: using governor menu
[    7.985636] usbcore: registered new interface driver usbhid
[    7.986023] usbhid: USB HID core driver
[    7.986739] dell_wmi: No known WMI GUID found
[    7.987101] acer_wmi: Acer Laptop ACPI-WMI Extras
[    7.987490] acer_wmi: No or unsupported WMI interface, unable to load
[    7.988271] IOAPIC[0]: Set routing entry (8-22 -> 0xa9 -> IRQ 22 Mode:1 Active:1 Dest:0)
[    7.988934] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    7.989594] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[    7.990033] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[    7.990517] ALSA hda_intel.c:2598 chipset global capabilities = 0x4401
[    7.990965] ALSA hda_intel.c:1091 Clearing TCSEL
[    7.991419] uhci_hcd 0000:00:1a.0: port 1 portsc 008a,00
[    7.991787] uhci_hcd 0000:00:1a.0: port 2 portsc 008a,00
[    7.999410] ALSA hda_intel.c:945 codec_mask = 0x4
[    7.999913] ALSA hda_intel.c:1392 codec #2 probed OK
[    8.004304] uhci_hcd 0000:00:1a.1: port 2 portsc 0082,00
[    8.005404] ALSA hda_codec.c:3955 hda_codec: model 'intel-x58' is selected for config 8086:22 (DX58SO)
[    8.006018] hda_codec: ALC889: SKU not ready 0x411111f0
[    8.006523] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input2
[    8.009891] ALSA hda_codec.c:2339 Cannot find slave Side Playback Volume, skipped
[    8.010448] ALSA hda_codec.c:2339 Cannot find slave Headphone Playback Volume, skipped
[    8.011009] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Volume, skipped
[    8.011558] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Volume, skipped
[    8.012122] ALSA hda_codec.c:2339 Cannot find slave Side Playback Switch, skipped
[    8.012675] ALSA hda_codec.c:2339 Cannot find slave Mono Playback Switch, skipped
[    8.013221] ALSA hda_codec.c:2339 Cannot find slave Line-Out Playback Switch, skipped
[    8.014392] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input3
[    8.015359] ALSA device list:
[    8.015622]   #0: HDA Intel at 0xf7f00000 irq 45
[    8.015945] oprofile: using NMI interrupt.
[    8.016269] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.016668] netem: version 1.3
[    8.016933] Netfilter messages via NETLINK v0.30.
[    8.017309] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    8.018343] ctnetlink v0.93: registering with nfnetlink.
[    8.018728] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    8.019136] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    8.019770] xt_time: kernel timezone is -0000
[    8.021463] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.024912] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[    8.025376] arp_tables: (C) 2002 David S. Miller
[    8.025735] TCP bic registered
[    8.025998] TCP cubic registered
[    8.026325] TCP westwood registered
[    8.026606] TCP highspeed registered
[    8.026888] TCP hybla registered
[    8.027158] TCP htcp registered
[    8.027431] TCP vegas registered
[    8.027700] TCP veno registered
[    8.027968] TCP scalable registered
[    8.028300] TCP lp registered
[    8.028560] TCP yeah registered
[    8.028826] TCP illinois registered
[    8.029104] Initializing XFRM netlink socket
[    8.029278] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.029784] NET: Registered protocol family 17
[    8.030108] NET: Registered protocol family 15
[    8.030634] Bridge firewalling registered
[    8.030946] Ebtables v2.0 registered
[    8.031331] 
[    8.031331] printing PIC contents
[    8.031812] ... PIC  IMR: ffff
[    8.032076] ... PIC  IRR: 0c21
[    8.032395] ... PIC  ISR: 0000
[    8.032661] ... PIC ELCR: 0c20
[    8.032926] printing local APIC contents on CPU#0/0:
[    8.033260] ... APIC ID:      00000000 (0)
[    8.033560] ... APIC VERSION: 00060015
[    8.033847] ... APIC TASKPRI: 00000000 (00)
[    8.034151] ... APIC PROCPRI: 00000000
[    8.034439] ... APIC LDR: 01000000
[    8.034714] ... APIC DFR: ffffffff
[    8.034989] ... APIC SPIV: 000001ff
[    8.035266] ... APIC ISR field:
[    8.035532] 0000000000000000000000000000000000000000000000000000000000000000
[    8.036212] ... APIC TMR field:
[    8.036477] 0000000000000000000000000000000000020000000000000000000000000000
[    8.037157] ... APIC IRR field:
[    8.037422] 0000000000030000000000000000000000000200000000000000000000000000
[    8.038101] ... APIC ESR: 00000000
[    8.038379] ... APIC ICR: 000000ef
[    8.038654] ... APIC ICR2: 07000000
[    8.038932] ... APIC LVTT: 000000ef
[    8.039210] ... APIC LVTPC: 00000400
[    8.039491] ... APIC LVT0: 00010700
[    8.039769] ... APIC LVT1: 00000400
[    8.040046] ... APIC LVTERR: 000000fe
[    8.040331] ... APIC TMICT: 00062e45
[    8.040613] ... APIC TMCCT: 0000f558
[    8.040894] ... APIC TDCR: 00000003
[    8.041172] 
[    8.041377] number of MP IRQ sources: 15.
[    8.041709] number of IO-APIC #8 registers: 24.
[    8.042056] testing the IO APIC.......................
[    8.042425] 
[    8.042660] IO APIC #8......
[    8.042946] .... register #00: 08000000
[    8.043321] .......    : physical APIC id: 08
[    8.043660] .......    : Delivery Type: 0
[    8.043987] .......    : LTS          : 0
[    8.044244] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.044681] .... register #01: 00170020
[    8.044975] .......     : max redirection entries: 17
[    8.045391] .......     : PRQ implemented: 0
[    8.045700] .......     : IO APIC version: 20
[    8.046012] .... IRQ redirection table:
[    8.046309]  NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
[    8.046665]  00 00  1    0    0   0   0    0    0    00
[    8.047046]  01 00  0    0    0   0   0    0    0    31
[    8.047488]  02 00  0    0    0   0   0    0    0    30
[    8.047869]  03 00  0    0    0   0   0    0    0    33
[    8.048222] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000
[    8.048679]  04 00  0    0    0   0   0    0    0    34
[    8.049087]  05 00  0    0    0   0   0    0    0    35
[    8.049586]  06 00  1    0    0   0   0    0    0    36
[    8.050023]  07 00  0    0    0   0   0    0    0    37
[    8.050472]  08 00  0    0    0   0   0    0    0    38
[    8.050908]  09 00  0    1    0   0   0    0    0    39
[    8.051395]  0a 00  0    0    0   0   0    0    0    3A
[    8.051831]  0b 00  0    0    0   0   0    0    0    3B
[    8.052273]  0c 00  0    0    0   0   0    0    0    3C
[    8.052707]  0d 00  0    0    0   0   0    0    0    3D
[    8.053231]  0e 00  0    0    0   0   0    0    0    3E
[    8.053642]  0f 00  0    0    0   0   0    0    0    3F
[    8.054077]  10 00  0    1    0   1   0    0    0    29
[    8.054547]  11 00  1    1    0   1   0    0    0    41
[    8.054982]  12 00  0    1    0   1   0    0    0    91
[    8.055477]  13 00  0    1    0   1   0    0    0    61
[    8.055916]  14 00  1    1    0   1   0    0    0    71
[    8.056352]  15 00  0    1    0   1   0    0    0    A1
[    8.056785]  16 00  1    1    0   1   0    0    0    A9
[    8.057276]  17 00  0    1    0   1   0    0    0    99
[    8.057710] IRQ to pin mappings:
[    8.058004] IRQ0 -> 0:2
[    8.058351] IRQ1 -> 0:1
[    8.058660] IRQ3 -> 0:3
[    8.058968] IRQ4 -> 0:4
[    8.059335] IRQ5 -> 0:5
[    8.059643] IRQ6 -> 0:6
[    8.059951] IRQ7 -> 0:7
[    8.060268] IRQ8 -> 0:8
[    8.060577] IRQ9 -> 0:9
[    8.060886] IRQ10 -> 0:10
[    8.061252] IRQ11 -> 0:11
[    8.061568] IRQ12 -> 0:12
[    8.061884] IRQ13 -> 0:13
[    8.062203] IRQ14 -> 0:14
[    8.062520] IRQ15 -> 0:15
[    8.062835] IRQ16 -> 0:16
[    8.063199] IRQ17 -> 0:17
[    8.063516] IRQ18 -> 0:18
[    8.063832] IRQ19 -> 0:19
[    8.064151] IRQ20 -> 0:20
[    8.064468] IRQ21 -> 0:21
[    8.064783] IRQ22 -> 0:22
[    8.065152] IRQ23 -> 0:23
[    8.065468] .................................... done.
[    8.066084] PM: Hibernation image not present or could not be loaded.
[    8.066497] registered taskstats version 1
[    8.067588]   Magic number: 7:829:70
[    8.068102] rtc_cmos 00:02: setting system clock to 2011-08-18 09:04:46 UTC (1313658286)
[    8.076170] hub 1-0:1.0: state 7 ports 6 chg 0016 evt 0000
[    8.076536] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[    8.082222] IP-Config: Complete:
[    8.082545]      device=eth0, addr=192.168.1.52, mask=255.255.255.0, gw=192.168.1.1,
[    8.083338]      host=fat, domain=, nis-domain=(none),
[    8.083785]      bootserver=192.168.1.11, rootserver=192.168.1.11, rootpath=
[    8.127252] ehci_hcd 0000:00:1a.7: port 1 high speed
[    8.127642] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    8.178873] usb 1-1: new high speed USB device number 2 using ehci_hcd
[    8.231928] ehci_hcd 0000:00:1a.7: port 1 high speed
[    8.232265] ehci_hcd 0000:00:1a.7: GetStatus port:1 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    8.302227] usb 1-1: default language 0x0409
[    8.308983] usb 1-1: udev 2, busnum 1, minor = 1
[    8.309309] usb 1-1: New USB device found, idVendor=0b95, idProduct=1780
[    8.309717] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    8.310132] usb 1-1: Product: AX88178 
[    8.310433] usb 1-1: Manufacturer: ASIX Elec. Corp.
[    8.310764] usb 1-1: SerialNumber: 000013
[    8.311247] usb 1-1: usb_probe_device
[    8.311541] usb 1-1: configuration #1 chosen from 1 choice
[    8.312447] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[    8.313445] asix 1-1:1.0: usb_probe_interface
[    8.313759] asix 1-1:1.0: usb_probe_interface - got id
[    8.925481] usb usb5: suspend_rh (auto-stop)
[    9.023480] asix 1-1:1.0: eth1: register 'asix' at usb-0000:00:1a.7-1, ASIX AX88178 USB 2.0 Ethernet, 00:23:54:5c:02:83
[    9.024211] /c/wfg/linux/drivers/usb/core/inode.c: creating file '002'
[    9.024674] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[    9.024691] md: Waiting for all devices to be available before autodetect
[    9.024693] md: If you don't use raid, use raid=noautodetect
[    9.025047] md: Autodetecting RAID arrays.
[    9.025048] md: Scanned 0 and added 0 devices.
[    9.025049] md: autorun ...
[    9.025050] md: ... autorun DONE.
[    9.026968] ehci_hcd 0000:00:1a.7: port 2 low speed --> companion
[    9.033375] VFS: Mounted root (nfs filesystem) on device 0:15.
[    9.033762] debug: unmapping init memory ffffffff81ebe000..ffffffff82172000
[    9.078003] ehci_hcd 0000:00:1a.7: GetStatus port:2 status 003002 0  ACK POWER OWNER sig=se0 CSC
[    9.078679] hub 1-0:1.0: port 4, status 0501, change 0000, 480 Mb/s
[    9.126294] stty used greatest stack depth: 4544 bytes left
[    9.130147] ehci_hcd 0000:00:1a.7: port 4 high speed
[    9.130512] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    9.155890] uname used greatest stack depth: 3872 bytes left
[    9.164180] sed used greatest stack depth: 3728 bytes left
[    9.174649] usb usb6: suspend_rh (auto-stop)
[    9.174738] usb usb8: suspend_rh (auto-stop)
[    9.175347] usb usb7: suspend_rh (auto-stop)
[    9.175738] usb usb4: suspend_rh (auto-stop)
[    9.181734] usb 1-4: new high speed USB device number 4 using ehci_hcd
[    9.198836] sh used greatest stack depth: 3696 bytes left
[    9.219421] mountpoint used greatest stack depth: 3600 bytes left
[    9.232703] ehci_hcd 0000:00:1a.7: port 4 high speed
[    9.233059] ehci_hcd 0000:00:1a.7: GetStatus port:4 status 001005 0  ACK POWER sig=se0 PE CONNECT
[    9.629654] amixer used greatest stack depth: 3552 bytes left
[   10.231628] usb 1-4: default language 0x0409
[   10.233491] usb 1-4: udev 4, busnum 1, minor = 3
[   10.233825] usb 1-4: New USB device found, idVendor=1307, idProduct=0165
[   10.234233] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   10.234706] usb 1-4: Product: USB Mass Storage Device
[   10.235051] usb 1-4: Manufacturer: Teclast Technology
[   10.235450] usb 1-4: SerialNumber: 0000000000020D
[   10.235934] usb 1-4: usb_probe_device
[   10.236238] usb 1-4: configuration #1 chosen from 1 choice
[   10.236740] usb 1-4: adding 1-4:1.0 (config #1, interface 0)
[   10.237196] usb-storage 1-4:1.0: usb_probe_interface
[   10.237602] usb-storage 1-4:1.0: usb_probe_interface - got id
[   10.238133] scsi9 : usb-storage 1-4:1.0
[   10.238753] /c/wfg/linux/drivers/usb/core/inode.c: creating file '004'
[   10.239194] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004
[   10.239622] uhci_hcd 0000:00:1a.0: port 2 portsc 01a3,00
[   10.239988] hub 3-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
[   10.344135] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
[   10.445728] usb 3-2: new low speed USB device number 2 using uhci_hcd
[   10.449369] usb 3-2: uhci_result_common: failed with status 440000
[   10.453357] usb 3-2: uhci_result_common: failed with status 440000
[   10.457343] usb 3-2: uhci_result_common: failed with status 440000
[   10.559420] usb 3-2: device descriptor read/64, error -71
[   10.663755] usb 3-2: uhci_result_common: failed with status 440000
[   10.667692] usb 3-2: uhci_result_common: failed with status 440000
[   10.671678] usb 3-2: uhci_result_common: failed with status 440000
[   10.773773] usb 3-2: device descriptor read/64, error -71
[   10.976092] usb 3-2: new low speed USB device number 3 using uhci_hcd
[   10.979725] usb 3-2: uhci_result_common: failed with status 440000
[   10.983747] usb 3-2: uhci_result_common: failed with status 440000
[   10.987768] usb 3-2: uhci_result_common: failed with status 440000
[   11.054017] EXT4-fs (sda5): recovery complete
[   11.054397] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[   11.089789] usb 3-2: device descriptor read/64, error -71
[   11.194127] usb 3-2: uhci_result_common: failed with status 440000
[   11.198047] usb 3-2: uhci_result_common: failed with status 440000
[   11.202104] usb 3-2: uhci_result_common: failed with status 440000
[   11.236907] scsi 9:0:0:0: Direct-Access     Teclast  CoolFlash        0.00 PQ: 0 ANSI: 2
[   11.304151] usb 3-2: device descriptor read/64, error -71
[   11.349823] sd 9:0:0:0: [sdb] 63084544 512-byte logical blocks: (32.2 GB/30.0 GiB)
[   11.351213] sd 9:0:0:0: [sdb] Write Protect is off
[   11.351587] sd 9:0:0:0: [sdb] Mode Sense: 00 00 00 00
[   11.352678] sd 9:0:0:0: [sdb] Asking for cache data failed
[   11.353085] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[   11.358102] sd 9:0:0:0: [sdb] Asking for cache data failed
[   11.358488] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[   11.492418]  sdb: sdb1 sdb2 sdb3
[   11.496796] sd 9:0:0:0: [sdb] Asking for cache data failed
[   11.497167] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[   11.497578] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[   11.506465] usb 3-2: new low speed USB device number 4 using uhci_hcd
[   11.510127] usb 3-2: uhci_result_common: failed with status 440000
[   11.714448] usb 3-2: uhci_result_common: failed with status 440000
[   11.824606] mount.nfs used greatest stack depth: 3312 bytes left
[   11.915163] usb 3-2: device not accepting address 4, error -71
[   12.016859] usb 3-2: new low speed USB device number 5 using uhci_hcd
[   12.020550] usb 3-2: uhci_result_common: failed with status 440000
[   12.075174] mount.nfs used greatest stack depth: 3152 bytes left
[   12.224866] usb 3-2: uhci_result_common: failed with status 440000
[   12.425598] usb 3-2: device not accepting address 5, error -71
[   12.425981] hub 3-0:1.0: unable to enumerate USB device on port 2
[   12.426359] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
[   12.426714] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0004
[   13.798853] XFS (sda7): Mounting Filesystem
[   13.866598] XFS (sda7): Ending clean mount